TY  - JOUR
AU  - Ćosić, Milena
AU  - Dojčinović, Marina
AU  - Acimović-Pavlović, Zagorka
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2786
AB  - Aluminium matrix composite (AMC) specimens were prepared using the compocasting technique. The reinforcements used were silicon carbide (SiC) particles with an average size of 30 mm. The influence of reinforced ratio of 10 wt-%SiC on cavitation behaviour was examined. The cavitation resistance of an AMC with SiC (AlSi/SiC) was evaluated using an ultrasonically induced cavitation test method. The mass loss of specimens was measured by an analytical method. The morphology of the damaged surface of tested composite was examined using scanning electron microscopy (SEM). It is shown that the cavitation rate of an AMC with SiC is almost the same as the CA6NM stainless steel, which is largely used in the production of hydraulic machinery components. Because the results show that the composites exhibited very good resistance to the cavitation erosion, this material can be successfully used under conditions where the cavitation resistance is needed.
PB  - Taylor & Francis Ltd, Abingdon
T2  - International Journal of Cast Metals Research
T1  - Fabrication and behaviour of Al-Si/SiC composite in cavitation conditions
EP  - 55
IS  - 1
SP  - 49
VL  - 27
DO  - 10.1179/1743133613Y.0000000078
ER  - 

@article{
author = "Ćosić, Milena and Dojčinović, Marina and Acimović-Pavlović, Zagorka",
year = "2014",
abstract = "Aluminium matrix composite (AMC) specimens were prepared using the compocasting technique. The reinforcements used were silicon carbide (SiC) particles with an average size of 30 mm. The influence of reinforced ratio of 10 wt-%SiC on cavitation behaviour was examined. The cavitation resistance of an AMC with SiC (AlSi/SiC) was evaluated using an ultrasonically induced cavitation test method. The mass loss of specimens was measured by an analytical method. The morphology of the damaged surface of tested composite was examined using scanning electron microscopy (SEM). It is shown that the cavitation rate of an AMC with SiC is almost the same as the CA6NM stainless steel, which is largely used in the production of hydraulic machinery components. Because the results show that the composites exhibited very good resistance to the cavitation erosion, this material can be successfully used under conditions where the cavitation resistance is needed.",
publisher = "Taylor & Francis Ltd, Abingdon",
journal = "International Journal of Cast Metals Research",
title = "Fabrication and behaviour of Al-Si/SiC composite in cavitation conditions",
pages = "55-49",
number = "1",
volume = "27",
doi = "10.1179/1743133613Y.0000000078"
}

Ćosić, M., Dojčinović, M.,& Acimović-Pavlović, Z.. (2014). Fabrication and behaviour of Al-Si/SiC composite in cavitation conditions. in International Journal of Cast Metals Research
Taylor & Francis Ltd, Abingdon., 27(1), 49-55.
https://doi.org/10.1179/1743133613Y.0000000078

Ćosić M, Dojčinović M, Acimović-Pavlović Z. Fabrication and behaviour of Al-Si/SiC composite in cavitation conditions. in International Journal of Cast Metals Research. 2014;27(1):49-55.
doi:10.1179/1743133613Y.0000000078 .

Ćosić, Milena, Dojčinović, Marina, Acimović-Pavlović, Zagorka, "Fabrication and behaviour of Al-Si/SiC composite in cavitation conditions" in International Journal of Cast Metals Research, 27, no. 1 (2014):49-55,
https://doi.org/10.1179/1743133613Y.0000000078 . .

TY  - JOUR
AU  - Prstić, Aurel
AU  - Acimović-Pavlović, Zagorka
AU  - Terzić, Anja
AU  - Pavlović, Ljubica
AU  - Grujić, Snežana
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2769
AB  - In this study, new refractory coatings based on synthesized cordierite for the casting applications were developed. The investigation included starting raw materials characterization, synthesis of the cordierite, design of the refractory coating as final product, and its application testing. The obtained results pointed out that coating suspension sediment stability was crucial quality parameter. Design and optimization of the coatings composition, with controlled rheological properties included, were achieved by application of different coating components, namely different suspension agents and by alteration of the coating production procedure. Cordierite, used as filler, was obtained by means of synthesis in the solid-state reaction on the basis of talc, kaolin, and alumina. The investigation showed that the application of these particular types of water/alcohol-based coatings has positive influence on surface quality and structural and mechanical properties of the castings of aluminum alloys obtained by casting into sand molds by means of evaporable models method, that is, evaporate pattern casting process.
PB  - Wiley, Hoboken
T2  - International Journal of Applied Ceramic Technology
T1  - Development of New Cordierite-Based Refractory Coatings for Casting Applications
EP  - 331
IS  - 2
SP  - 321
VL  - 11
DO  - 10.1111/ijac.12010
ER  - 

@article{
author = "Prstić, Aurel and Acimović-Pavlović, Zagorka and Terzić, Anja and Pavlović, Ljubica and Grujić, Snežana",
year = "2014",
abstract = "In this study, new refractory coatings based on synthesized cordierite for the casting applications were developed. The investigation included starting raw materials characterization, synthesis of the cordierite, design of the refractory coating as final product, and its application testing. The obtained results pointed out that coating suspension sediment stability was crucial quality parameter. Design and optimization of the coatings composition, with controlled rheological properties included, were achieved by application of different coating components, namely different suspension agents and by alteration of the coating production procedure. Cordierite, used as filler, was obtained by means of synthesis in the solid-state reaction on the basis of talc, kaolin, and alumina. The investigation showed that the application of these particular types of water/alcohol-based coatings has positive influence on surface quality and structural and mechanical properties of the castings of aluminum alloys obtained by casting into sand molds by means of evaporable models method, that is, evaporate pattern casting process.",
publisher = "Wiley, Hoboken",
journal = "International Journal of Applied Ceramic Technology",
title = "Development of New Cordierite-Based Refractory Coatings for Casting Applications",
pages = "331-321",
number = "2",
volume = "11",
doi = "10.1111/ijac.12010"
}

Prstić, A., Acimović-Pavlović, Z., Terzić, A., Pavlović, L.,& Grujić, S.. (2014). Development of New Cordierite-Based Refractory Coatings for Casting Applications. in International Journal of Applied Ceramic Technology
Wiley, Hoboken., 11(2), 321-331.
https://doi.org/10.1111/ijac.12010

Prstić A, Acimović-Pavlović Z, Terzić A, Pavlović L, Grujić S. Development of New Cordierite-Based Refractory Coatings for Casting Applications. in International Journal of Applied Ceramic Technology. 2014;11(2):321-331.
doi:10.1111/ijac.12010 .

Prstić, Aurel, Acimović-Pavlović, Zagorka, Terzić, Anja, Pavlović, Ljubica, Grujić, Snežana, "Development of New Cordierite-Based Refractory Coatings for Casting Applications" in International Journal of Applied Ceramic Technology, 11, no. 2 (2014):321-331,
https://doi.org/10.1111/ijac.12010 . .

TY  - JOUR
AU  - Ćosić, Milena
AU  - Acimović-Pavlović, Zagorka
AU  - Terzić, Anja
AU  - Dojčinović, Marina
AU  - Pavlović, Ljubica
PY  - 2012
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2164
AB  - The aim of this study was to investigate the influence of various process parameters on the microstructure of composite materials based on alloys All 8Wt%Si with the addition of 10Wt%SiC. The effect of stirring speed (1000 and 1500 rpm), stirring time 15 min and casting temperature 565 degrees C on the structural and mechanical properties are discussed. It was found that applying the stirring speed of 1500 rpm in semisolid state the best distribution of SiC particles in the matrix was achieved, which gave satisfying mechanical properties. In order to evaluate the quality of obtained composites and their possible application in the practice, tests were carried out under conditions of cavitation. Cavitation damage to the composite samples was determined using modified vibratory cavitation equipment. Mass loss and surface analysis of composite samples during the experiment were used as an indicator the level of cavitation damage. The results showed very good cavitation resistance which gives the possibility of using these materials in condition where cavitation resistance is needed.
PB  - Modtech Publishing House, Iasi
T2  - Modtech 2012: New Face of T M C R, Vols I and II
T1  - The possibility of obtaining. Composite al18wt%si/sic by compocasting process
EP  - 252
SP  - 249
UR  - https://hdl.handle.net/21.15107/rcub_technorep_2164
ER  - 

@article{
author = "Ćosić, Milena and Acimović-Pavlović, Zagorka and Terzić, Anja and Dojčinović, Marina and Pavlović, Ljubica",
year = "2012",
abstract = "The aim of this study was to investigate the influence of various process parameters on the microstructure of composite materials based on alloys All 8Wt%Si with the addition of 10Wt%SiC. The effect of stirring speed (1000 and 1500 rpm), stirring time 15 min and casting temperature 565 degrees C on the structural and mechanical properties are discussed. It was found that applying the stirring speed of 1500 rpm in semisolid state the best distribution of SiC particles in the matrix was achieved, which gave satisfying mechanical properties. In order to evaluate the quality of obtained composites and their possible application in the practice, tests were carried out under conditions of cavitation. Cavitation damage to the composite samples was determined using modified vibratory cavitation equipment. Mass loss and surface analysis of composite samples during the experiment were used as an indicator the level of cavitation damage. The results showed very good cavitation resistance which gives the possibility of using these materials in condition where cavitation resistance is needed.",
publisher = "Modtech Publishing House, Iasi",
journal = "Modtech 2012: New Face of T M C R, Vols I and II",
title = "The possibility of obtaining. Composite al18wt%si/sic by compocasting process",
pages = "252-249",
url = "https://hdl.handle.net/21.15107/rcub_technorep_2164"
}

Ćosić, M., Acimović-Pavlović, Z., Terzić, A., Dojčinović, M.,& Pavlović, L.. (2012). The possibility of obtaining. Composite al18wt%si/sic by compocasting process. in Modtech 2012: New Face of T M C R, Vols I and II
Modtech Publishing House, Iasi., 249-252.
https://hdl.handle.net/21.15107/rcub_technorep_2164

Ćosić M, Acimović-Pavlović Z, Terzić A, Dojčinović M, Pavlović L. The possibility of obtaining. Composite al18wt%si/sic by compocasting process. in Modtech 2012: New Face of T M C R, Vols I and II. 2012;:249-252.
https://hdl.handle.net/21.15107/rcub_technorep_2164 .

Ćosić, Milena, Acimović-Pavlović, Zagorka, Terzić, Anja, Dojčinović, Marina, Pavlović, Ljubica, "The possibility of obtaining. Composite al18wt%si/sic by compocasting process" in Modtech 2012: New Face of T M C R, Vols I and II (2012):249-252,
https://hdl.handle.net/21.15107/rcub_technorep_2164 .

TY  - JOUR
AU  - Prstić, Aurel
AU  - Acimović-Pavlović, Zagorka
AU  - Andrić, Ljubiša
AU  - Grujić, Snežana
AU  - Tumbulović, Ljiljana
PY  - 2012
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2005
AB  - This paper presents the results of mechanical activation of filler based on mica and the influence on the quality of foundry coatings. The coating was applied for lining of evaporable model in Lost foam casting process. The examinations of synthesis, characterization and application of refractory coatings showed that sediment stability of coating suspension was crucial quality parameter. Coating composition optimization with the controlled reologic properties was achieved by applying different coating components and by alteration of coating production procedure. For the assessment of possibilities of using mica as refractory fillers the comparative test were done with the coating on the basis of talk Ceramic powders talk and mica were, first, grind down in the so-called fine fractions, and then used as a heat-resisting fillers. The talc and mica samples were tested by the following methods.: Xray diffraction analysis, diffraction thermal analysis and qualitative mineralogical analysis on scanning electronic micrpscope. The shape and grain size were analyzed by the program package OZARIA 2.5. For assessing the quality of the coatings and the effects of their application detailed analysis of structural and mechanical properties of the castings were done. Also, the radiographic examination of castings on the type of x-ray device SAIFORT-S200 was done. Application of refractory coatings on the basis of talk and mica showed a positive influence on the structural and mechanical properties of castings of aluminum-silicon alloys.
PB  - Editura Stiintifica Fmr, Bucharest
T2  - Metalurgia International
T1  - Mica based coating for application in lost foam casting process
EP  - 96
IS  - 7
SP  - 90
VL  - 17
UR  - https://hdl.handle.net/21.15107/rcub_technorep_2005
ER  - 

@article{
author = "Prstić, Aurel and Acimović-Pavlović, Zagorka and Andrić, Ljubiša and Grujić, Snežana and Tumbulović, Ljiljana",
year = "2012",
abstract = "This paper presents the results of mechanical activation of filler based on mica and the influence on the quality of foundry coatings. The coating was applied for lining of evaporable model in Lost foam casting process. The examinations of synthesis, characterization and application of refractory coatings showed that sediment stability of coating suspension was crucial quality parameter. Coating composition optimization with the controlled reologic properties was achieved by applying different coating components and by alteration of coating production procedure. For the assessment of possibilities of using mica as refractory fillers the comparative test were done with the coating on the basis of talk Ceramic powders talk and mica were, first, grind down in the so-called fine fractions, and then used as a heat-resisting fillers. The talc and mica samples were tested by the following methods.: Xray diffraction analysis, diffraction thermal analysis and qualitative mineralogical analysis on scanning electronic micrpscope. The shape and grain size were analyzed by the program package OZARIA 2.5. For assessing the quality of the coatings and the effects of their application detailed analysis of structural and mechanical properties of the castings were done. Also, the radiographic examination of castings on the type of x-ray device SAIFORT-S200 was done. Application of refractory coatings on the basis of talk and mica showed a positive influence on the structural and mechanical properties of castings of aluminum-silicon alloys.",
publisher = "Editura Stiintifica Fmr, Bucharest",
journal = "Metalurgia International",
title = "Mica based coating for application in lost foam casting process",
pages = "96-90",
number = "7",
volume = "17",
url = "https://hdl.handle.net/21.15107/rcub_technorep_2005"
}

Prstić, A., Acimović-Pavlović, Z., Andrić, L., Grujić, S.,& Tumbulović, L.. (2012). Mica based coating for application in lost foam casting process. in Metalurgia International
Editura Stiintifica Fmr, Bucharest., 17(7), 90-96.
https://hdl.handle.net/21.15107/rcub_technorep_2005

Prstić A, Acimović-Pavlović Z, Andrić L, Grujić S, Tumbulović L. Mica based coating for application in lost foam casting process. in Metalurgia International. 2012;17(7):90-96.
https://hdl.handle.net/21.15107/rcub_technorep_2005 .

Prstić, Aurel, Acimović-Pavlović, Zagorka, Andrić, Ljubiša, Grujić, Snežana, Tumbulović, Ljiljana, "Mica based coating for application in lost foam casting process" in Metalurgia International, 17, no. 7 (2012):90-96,
https://hdl.handle.net/21.15107/rcub_technorep_2005 .

TY  - JOUR
AU  - Ćosić, Milena
AU  - Dojčinović, Marina
AU  - Acimović-Pavlović, Zagorka
PY  - 2012
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1979
AB  - The aim of this work was to test the influence of various process parameters to obtain composite materials based on the Al18Wt%Si alloy with addition of 10Wt%SiC.For a comparative analysis purposes, the samples obtained by rheocasting process were being casted with application of the rotation speed of 1500rpm, temperature of 565 degrees C and the time of 15 minutes.Having applied a combined stirring procedure from 500 - 1500rpm, it was noticed in the semisolid state that the best paricle distribution of the reinforcing material (SiC) was attained in the.metal matrix composite. The total time required for a compocasting process was 15 minutes; the samples were being casted from the temperature of 565 degrees C. cavitation damage of both composite samples and the samples obtained by rheocasting process was being determined with application of a modified vibration-cavitation equipment. A mass loss and an analysis of the sample surface during the experiment were used as an indicator to determine the level of sample damage caused by cavitation. Test results show a very good resistance to cavitation of composite materials, facilitating a possibility to apply these materials in the conditions demanding cavitation resistance. In the case of rheocasting samples, cavitation resistance is conditioned by presence of porosity leading to faster wear.
PB  - Editura Stiintifica Fmr, Bucharest
T2  - Metalurgia International
T1  - Characterization of microstructure and properties of hypereutectic al18wt%si alloys reinforced by 10%sic alloy
EP  - 106
IS  - 6
SP  - 102
VL  - 17
UR  - https://hdl.handle.net/21.15107/rcub_technorep_1979
ER  - 

@article{
author = "Ćosić, Milena and Dojčinović, Marina and Acimović-Pavlović, Zagorka",
year = "2012",
abstract = "The aim of this work was to test the influence of various process parameters to obtain composite materials based on the Al18Wt%Si alloy with addition of 10Wt%SiC.For a comparative analysis purposes, the samples obtained by rheocasting process were being casted with application of the rotation speed of 1500rpm, temperature of 565 degrees C and the time of 15 minutes.Having applied a combined stirring procedure from 500 - 1500rpm, it was noticed in the semisolid state that the best paricle distribution of the reinforcing material (SiC) was attained in the.metal matrix composite. The total time required for a compocasting process was 15 minutes; the samples were being casted from the temperature of 565 degrees C. cavitation damage of both composite samples and the samples obtained by rheocasting process was being determined with application of a modified vibration-cavitation equipment. A mass loss and an analysis of the sample surface during the experiment were used as an indicator to determine the level of sample damage caused by cavitation. Test results show a very good resistance to cavitation of composite materials, facilitating a possibility to apply these materials in the conditions demanding cavitation resistance. In the case of rheocasting samples, cavitation resistance is conditioned by presence of porosity leading to faster wear.",
publisher = "Editura Stiintifica Fmr, Bucharest",
journal = "Metalurgia International",
title = "Characterization of microstructure and properties of hypereutectic al18wt%si alloys reinforced by 10%sic alloy",
pages = "106-102",
number = "6",
volume = "17",
url = "https://hdl.handle.net/21.15107/rcub_technorep_1979"
}

Ćosić, M., Dojčinović, M.,& Acimović-Pavlović, Z.. (2012). Characterization of microstructure and properties of hypereutectic al18wt%si alloys reinforced by 10%sic alloy. in Metalurgia International
Editura Stiintifica Fmr, Bucharest., 17(6), 102-106.
https://hdl.handle.net/21.15107/rcub_technorep_1979

Ćosić M, Dojčinović M, Acimović-Pavlović Z. Characterization of microstructure and properties of hypereutectic al18wt%si alloys reinforced by 10%sic alloy. in Metalurgia International. 2012;17(6):102-106.
https://hdl.handle.net/21.15107/rcub_technorep_1979 .

Ćosić, Milena, Dojčinović, Marina, Acimović-Pavlović, Zagorka, "Characterization of microstructure and properties of hypereutectic al18wt%si alloys reinforced by 10%sic alloy" in Metalurgia International, 17, no. 6 (2012):102-106,
https://hdl.handle.net/21.15107/rcub_technorep_1979 .

TY  - JOUR
AU  - Grujić, Snežana
AU  - Blagojević, Nikola S.
AU  - Tošić, Mihajlo B.
AU  - Živanović, Vladimir D.
AU  - Acimović-Pavlović, Zagorka
PY  - 2010
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1595
AB  - The kinetics and mechanism of isothermal crystal growth of K2TiGe3O9 from a glass of the same stoichiometric composition were studied. The crystal growth rate, U, in the range 1x10-11-1.27x10-10 m s-1 was experimentally determined in the temperature interval 540-600°C. In the range of high under-cooling, Δt, 435-375°C, spherical crystals growing at (374±19) kJ mol-1 was observed.
AB  - Pod izotermskim uslovima proučavana je kinetika i mehanizam rasta K2TiGe3O9 kristala iz stakla istog stehiometrijskog sastava. U intervalu temperature 540-600°C eksperimentalno su određene brzine rasta kristala, U, 1x10-11-1.27x10-10 m s-1. Pokazano je da se u oblasti visokih pothlađenja, Δt, 435-375°C, rast sfernih kristala ove faze odvija po mehanizmu zavojne dislokacije. Dobijena je energija aktivacije rasta kristala GD=(374±19) kJ mol-1.
PB  - Serbian Chemical Society, Belgrade
T2  - Journal of the Serbian Chemical Society
T1  - Crystal growth of K2TiGe3O9 in the glass
T1  - Rast kristala K2TiGe3O9 u staklu
EP  - 1604
IS  - 11
SP  - 1595
VL  - 75
UR  - https://hdl.handle.net/21.15107/rcub_technorep_1595
ER  - 

@article{
author = "Grujić, Snežana and Blagojević, Nikola S. and Tošić, Mihajlo B. and Živanović, Vladimir D. and Acimović-Pavlović, Zagorka",
year = "2010",
abstract = "The kinetics and mechanism of isothermal crystal growth of K2TiGe3O9 from a glass of the same stoichiometric composition were studied. The crystal growth rate, U, in the range 1x10-11-1.27x10-10 m s-1 was experimentally determined in the temperature interval 540-600°C. In the range of high under-cooling, Δt, 435-375°C, spherical crystals growing at (374±19) kJ mol-1 was observed., Pod izotermskim uslovima proučavana je kinetika i mehanizam rasta K2TiGe3O9 kristala iz stakla istog stehiometrijskog sastava. U intervalu temperature 540-600°C eksperimentalno su određene brzine rasta kristala, U, 1x10-11-1.27x10-10 m s-1. Pokazano je da se u oblasti visokih pothlađenja, Δt, 435-375°C, rast sfernih kristala ove faze odvija po mehanizmu zavojne dislokacije. Dobijena je energija aktivacije rasta kristala GD=(374±19) kJ mol-1.",
publisher = "Serbian Chemical Society, Belgrade",
journal = "Journal of the Serbian Chemical Society",
title = "Crystal growth of K2TiGe3O9 in the glass, Rast kristala K2TiGe3O9 u staklu",
pages = "1604-1595",
number = "11",
volume = "75",
url = "https://hdl.handle.net/21.15107/rcub_technorep_1595"
}

Grujić, S., Blagojević, N. S., Tošić, M. B., Živanović, V. D.,& Acimović-Pavlović, Z.. (2010). Crystal growth of K2TiGe3O9 in the glass. in Journal of the Serbian Chemical Society
Serbian Chemical Society, Belgrade., 75(11), 1595-1604.
https://hdl.handle.net/21.15107/rcub_technorep_1595

Grujić S, Blagojević NS, Tošić MB, Živanović VD, Acimović-Pavlović Z. Crystal growth of K2TiGe3O9 in the glass. in Journal of the Serbian Chemical Society. 2010;75(11):1595-1604.
https://hdl.handle.net/21.15107/rcub_technorep_1595 .

Grujić, Snežana, Blagojević, Nikola S., Tošić, Mihajlo B., Živanović, Vladimir D., Acimović-Pavlović, Zagorka, "Crystal growth of K2TiGe3O9 in the glass" in Journal of the Serbian Chemical Society, 75, no. 11 (2010):1595-1604,
https://hdl.handle.net/21.15107/rcub_technorep_1595 .

TY  - JOUR
AU  - Volkov-Husović, Tatjana
AU  - Jančić-Heinemann, Radmila
AU  - Mitraković, Dragan
AU  - Acimović-Pavlović, Zagorka
AU  - Raić, Karlo
PY  - 2006
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/903
AB  - During examination of refractory specimen, one of the most important characteristics is their resistance to thermal shock. Standard method of testing is based on monitoring the surface shanging during thermal stability testing. Samples are photographed before and during thermal stability testing. Image analysis program was used to determine the amount of surface deterioriation. Obtained results for surface deterioriation were compared to the results of water quench test, as well as with strength degradation. The obtained results will be used for prediction of thermal stability behavior of refractory specimen.
AB  - Prilikom ispitivanja vatrostalnih materijala ispitivanje termošoka pretstavlja jednu od najvažnijih osobina. Standardna metoda ispitivanja termostabilnosti se zasniva na praćenju promena na površini uzorka usled naglih promena temperature. Uzorci se snimaju pre ispitivanja, i u toku ispitivanja otpornosti na termošok. Na osnovu upotrebe programa za analizu slike praćena je promena stepena oštećenja u uzorku. Dobijeni rezultati za promenu stepena oštećenja su upoređeni sa rezultatima standardne metode vodenog hlađenja, kao i sa promenom čvrstoće uzorka. Na osnovu analize dobijenih rezultata date su preporuke za predviđanje ponašanja materijala izloženog termošoku.
PB  - Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd
T2  - Materijali i konstrukcije
T1  - The use of image analysis program for the determination of surface deterioration of refractory specimen during thermal shock
T1  - Korišćenje programa za analizu slike za određivanje stepena oštećenja vatrostalnog uzorka pri termošoku
EP  - 63
IS  - 1-2
SP  - 60
VL  - 49
UR  - https://hdl.handle.net/21.15107/rcub_technorep_903
ER  - 

@article{
author = "Volkov-Husović, Tatjana and Jančić-Heinemann, Radmila and Mitraković, Dragan and Acimović-Pavlović, Zagorka and Raić, Karlo",
year = "2006",
abstract = "During examination of refractory specimen, one of the most important characteristics is their resistance to thermal shock. Standard method of testing is based on monitoring the surface shanging during thermal stability testing. Samples are photographed before and during thermal stability testing. Image analysis program was used to determine the amount of surface deterioriation. Obtained results for surface deterioriation were compared to the results of water quench test, as well as with strength degradation. The obtained results will be used for prediction of thermal stability behavior of refractory specimen., Prilikom ispitivanja vatrostalnih materijala ispitivanje termošoka pretstavlja jednu od najvažnijih osobina. Standardna metoda ispitivanja termostabilnosti se zasniva na praćenju promena na površini uzorka usled naglih promena temperature. Uzorci se snimaju pre ispitivanja, i u toku ispitivanja otpornosti na termošok. Na osnovu upotrebe programa za analizu slike praćena je promena stepena oštećenja u uzorku. Dobijeni rezultati za promenu stepena oštećenja su upoređeni sa rezultatima standardne metode vodenog hlađenja, kao i sa promenom čvrstoće uzorka. Na osnovu analize dobijenih rezultata date su preporuke za predviđanje ponašanja materijala izloženog termošoku.",
publisher = "Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd",
journal = "Materijali i konstrukcije",
title = "The use of image analysis program for the determination of surface deterioration of refractory specimen during thermal shock, Korišćenje programa za analizu slike za određivanje stepena oštećenja vatrostalnog uzorka pri termošoku",
pages = "63-60",
number = "1-2",
volume = "49",
url = "https://hdl.handle.net/21.15107/rcub_technorep_903"
}

Volkov-Husović, T., Jančić-Heinemann, R., Mitraković, D., Acimović-Pavlović, Z.,& Raić, K.. (2006). The use of image analysis program for the determination of surface deterioration of refractory specimen during thermal shock. in Materijali i konstrukcije
Društvo za ispitivanje i istraživanje materijala i konstrukcija Srbije, Beograd., 49(1-2), 60-63.
https://hdl.handle.net/21.15107/rcub_technorep_903

Volkov-Husović T, Jančić-Heinemann R, Mitraković D, Acimović-Pavlović Z, Raić K. The use of image analysis program for the determination of surface deterioration of refractory specimen during thermal shock. in Materijali i konstrukcije. 2006;49(1-2):60-63.
https://hdl.handle.net/21.15107/rcub_technorep_903 .

Volkov-Husović, Tatjana, Jančić-Heinemann, Radmila, Mitraković, Dragan, Acimović-Pavlović, Zagorka, Raić, Karlo, "The use of image analysis program for the determination of surface deterioration of refractory specimen during thermal shock" in Materijali i konstrukcije, 49, no. 1-2 (2006):60-63,
https://hdl.handle.net/21.15107/rcub_technorep_903 .