TY  - JOUR
AU  - Tošić, Miloš
AU  - Rajić, Vladimir
AU  - Pjević, Dejan
AU  - Stojadinović, Stevan
AU  - Krstulović, Nikša
AU  - Dimitrijević-Branković, Suzana
AU  - Momčilović, Miloš
PY  - 2024
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7412
AB  - This study proposes a simple and controlled method for producing TiO2 with phase junction, oxygen vacancies, and Ti3+ by combining picosecond pulsed laser irradiation and electrochemical anodization. Ti mesh was pretreated by irradiating with a picosecond pulsed laser technique using an Nd:YAG laser (1064 nm) at two fluencies, 15 J/cm2 and 30 J/cm2 . The samples were then subjected to electrochemical anodization to form TiO2 nanotube arrays on the previously laser-treated surface. This study will investigate the possibility of forming TiO2 nanotube arrays on a pre-laser-treated Ti substrate and determine their physicochemical and photocatalytic properties. The samples were characterized by FESEM, XRD, Raman, XPS, and UV-Vis DRS. UV-Vis spectroscopy was used to observe the progress of photocatalytic degradation for all samples, and degradation products were determined using GC-MS. With the synergistic effects of phase junction, oxygen vacancies, and Ti3+, the laser-treated TiO2 with 30 J/cm2 showed a higher photocatalytic degradation rate (85.1%) of the pesticide carbofuran compared to non-laser-treated TiO2 (54.8%), remaining stable during successive degradation cycles, which has promising practical applications.
T2  - Photonics
T1  - Synergy of Nd:YAG Picosecond Pulsed Laser Irradiation and Electrochemical Anodization in the Formation of TiO2 Nanostructures for the Photocatalytic Degradation of Pesticide Carbofuran
IS  - 3
SP  - 284
VL  - 11
DO  - 10.3390/photonics11030284
ER  - 

@article{
author = "Tošić, Miloš and Rajić, Vladimir and Pjević, Dejan and Stojadinović, Stevan and Krstulović, Nikša and Dimitrijević-Branković, Suzana and Momčilović, Miloš",
year = "2024",
abstract = "This study proposes a simple and controlled method for producing TiO2 with phase junction, oxygen vacancies, and Ti3+ by combining picosecond pulsed laser irradiation and electrochemical anodization. Ti mesh was pretreated by irradiating with a picosecond pulsed laser technique using an Nd:YAG laser (1064 nm) at two fluencies, 15 J/cm2 and 30 J/cm2 . The samples were then subjected to electrochemical anodization to form TiO2 nanotube arrays on the previously laser-treated surface. This study will investigate the possibility of forming TiO2 nanotube arrays on a pre-laser-treated Ti substrate and determine their physicochemical and photocatalytic properties. The samples were characterized by FESEM, XRD, Raman, XPS, and UV-Vis DRS. UV-Vis spectroscopy was used to observe the progress of photocatalytic degradation for all samples, and degradation products were determined using GC-MS. With the synergistic effects of phase junction, oxygen vacancies, and Ti3+, the laser-treated TiO2 with 30 J/cm2 showed a higher photocatalytic degradation rate (85.1%) of the pesticide carbofuran compared to non-laser-treated TiO2 (54.8%), remaining stable during successive degradation cycles, which has promising practical applications.",
journal = "Photonics",
title = "Synergy of Nd:YAG Picosecond Pulsed Laser Irradiation and Electrochemical Anodization in the Formation of TiO2 Nanostructures for the Photocatalytic Degradation of Pesticide Carbofuran",
number = "3",
pages = "284",
volume = "11",
doi = "10.3390/photonics11030284"
}

Tošić, M., Rajić, V., Pjević, D., Stojadinović, S., Krstulović, N., Dimitrijević-Branković, S.,& Momčilović, M.. (2024). Synergy of Nd:YAG Picosecond Pulsed Laser Irradiation and Electrochemical Anodization in the Formation of TiO2 Nanostructures for the Photocatalytic Degradation of Pesticide Carbofuran. in Photonics, 11(3), 284.
https://doi.org/10.3390/photonics11030284

Tošić M, Rajić V, Pjević D, Stojadinović S, Krstulović N, Dimitrijević-Branković S, Momčilović M. Synergy of Nd:YAG Picosecond Pulsed Laser Irradiation and Electrochemical Anodization in the Formation of TiO2 Nanostructures for the Photocatalytic Degradation of Pesticide Carbofuran. in Photonics. 2024;11(3):284.
doi:10.3390/photonics11030284 .

Tošić, Miloš, Rajić, Vladimir, Pjević, Dejan, Stojadinović, Stevan, Krstulović, Nikša, Dimitrijević-Branković, Suzana, Momčilović, Miloš, "Synergy of Nd:YAG Picosecond Pulsed Laser Irradiation and Electrochemical Anodization in the Formation of TiO2 Nanostructures for the Photocatalytic Degradation of Pesticide Carbofuran" in Photonics, 11, no. 3 (2024):284,
https://doi.org/10.3390/photonics11030284 . .

TY  - JOUR
AU  - Laketić, Slađana
AU  - Rakin, Marko
AU  - Momčilović, Miloš
AU  - Ciganović, Jovan
AU  - Veljović, Đorđe
AU  - Cvijović-Alagić, Ivana
PY  - 2021
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/16
AB  - The effects of picosecond Nd:YAG laser irradiation on chemical and morphological surface characteristics of the commercially pure titanium and Ti-13Nb-13Zr alloy in air and argon atmospheres were studied under different laser output energy values. During the interaction of laser irradiation with the investigated materials, a part of the energy was absorbed on the target surface, influencing surface modifications. Laser beam interaction with the target surface resulted in various morphological alterations, resulting in crater formation and the presence of microcracks and hydrodynamic structures. Moreover, different chemical changes were induced on the target materials' surfaces, resulting in the titanium oxide formation in the irradiation-affected area and consequently increasing the irradiation energy absorption. Given the high energy absorption at the site of interaction, the dimensions of the surface damaged area increased. Consequently, surface roughness increased. The appearance of surface oxides also led to the increased material hardness in the surface-modified area. Observed chemical and morphological changes were pronounced after laser irradiation of the Ti-13Nb-13Zr alloy surface.
PB  - Springer, New York
T2  - International Journal of Minerals Metallurgy and Materials
T1  - Surface modifications of biometallic commercially pure Ti and Ti-13Nb-13Zr alloy by picosecond Nd:YAG laser
DO  - 10.1007/s12613-020-2061-9
ER  - 

@article{
author = "Laketić, Slađana and Rakin, Marko and Momčilović, Miloš and Ciganović, Jovan and Veljović, Đorđe and Cvijović-Alagić, Ivana",
year = "2021",
abstract = "The effects of picosecond Nd:YAG laser irradiation on chemical and morphological surface characteristics of the commercially pure titanium and Ti-13Nb-13Zr alloy in air and argon atmospheres were studied under different laser output energy values. During the interaction of laser irradiation with the investigated materials, a part of the energy was absorbed on the target surface, influencing surface modifications. Laser beam interaction with the target surface resulted in various morphological alterations, resulting in crater formation and the presence of microcracks and hydrodynamic structures. Moreover, different chemical changes were induced on the target materials' surfaces, resulting in the titanium oxide formation in the irradiation-affected area and consequently increasing the irradiation energy absorption. Given the high energy absorption at the site of interaction, the dimensions of the surface damaged area increased. Consequently, surface roughness increased. The appearance of surface oxides also led to the increased material hardness in the surface-modified area. Observed chemical and morphological changes were pronounced after laser irradiation of the Ti-13Nb-13Zr alloy surface.",
publisher = "Springer, New York",
journal = "International Journal of Minerals Metallurgy and Materials",
title = "Surface modifications of biometallic commercially pure Ti and Ti-13Nb-13Zr alloy by picosecond Nd:YAG laser",
doi = "10.1007/s12613-020-2061-9"
}

Laketić, S., Rakin, M., Momčilović, M., Ciganović, J., Veljović, Đ.,& Cvijović-Alagić, I.. (2021). Surface modifications of biometallic commercially pure Ti and Ti-13Nb-13Zr alloy by picosecond Nd:YAG laser. in International Journal of Minerals Metallurgy and Materials
Springer, New York..
https://doi.org/10.1007/s12613-020-2061-9

Laketić S, Rakin M, Momčilović M, Ciganović J, Veljović Đ, Cvijović-Alagić I. Surface modifications of biometallic commercially pure Ti and Ti-13Nb-13Zr alloy by picosecond Nd:YAG laser. in International Journal of Minerals Metallurgy and Materials. 2021;.
doi:10.1007/s12613-020-2061-9 .

Laketić, Slađana, Rakin, Marko, Momčilović, Miloš, Ciganović, Jovan, Veljović, Đorđe, Cvijović-Alagić, Ivana, "Surface modifications of biometallic commercially pure Ti and Ti-13Nb-13Zr alloy by picosecond Nd:YAG laser" in International Journal of Minerals Metallurgy and Materials (2021),
https://doi.org/10.1007/s12613-020-2061-9 . .

TY  - JOUR
AU  - Petronić, Sanja Z.
AU  - Milosavljević, Anđelka
AU  - Milovanović, Dubravka
AU  - Momčilović, Miloš
AU  - Radovanović, Željko
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1886
AB  - We investigate samples of austenitic materials - stainless steel and iron-based superalloy - which are widely used at high temperatures and pressures. The samples were exposed to Nd(3+):YAG laser pulses with a wavelength of 1064 nm and a pulse duration of 170 ps. We employ different pulse energies and number of pulses. The spots appearing after the laser irradiation were examined by optical and scanning electron microscopy and analyzed by energy-dispersive spectroscopy. We also perform Vickers microhardness tests. We discuss the microstructure changes caused by different energy and number of pulses in air and in a He-enriched atmosphere with the aim to determine optimum laser parameters in surface-treatment technology.
PB  - Springer, New York
T2  - Journal of Russian Laser Research
T1  - Influence of picosecond laser pulses on the microstructure of austenitic materials
EP  - 571
IS  - 6
SP  - 564
VL  - 32
DO  - 10.1007/s10946-011-9247-6
ER  - 

@article{
author = "Petronić, Sanja Z. and Milosavljević, Anđelka and Milovanović, Dubravka and Momčilović, Miloš and Radovanović, Željko",
year = "2011",
abstract = "We investigate samples of austenitic materials - stainless steel and iron-based superalloy - which are widely used at high temperatures and pressures. The samples were exposed to Nd(3+):YAG laser pulses with a wavelength of 1064 nm and a pulse duration of 170 ps. We employ different pulse energies and number of pulses. The spots appearing after the laser irradiation were examined by optical and scanning electron microscopy and analyzed by energy-dispersive spectroscopy. We also perform Vickers microhardness tests. We discuss the microstructure changes caused by different energy and number of pulses in air and in a He-enriched atmosphere with the aim to determine optimum laser parameters in surface-treatment technology.",
publisher = "Springer, New York",
journal = "Journal of Russian Laser Research",
title = "Influence of picosecond laser pulses on the microstructure of austenitic materials",
pages = "571-564",
number = "6",
volume = "32",
doi = "10.1007/s10946-011-9247-6"
}

Petronić, S. Z., Milosavljević, A., Milovanović, D., Momčilović, M.,& Radovanović, Ž.. (2011). Influence of picosecond laser pulses on the microstructure of austenitic materials. in Journal of Russian Laser Research
Springer, New York., 32(6), 564-571.
https://doi.org/10.1007/s10946-011-9247-6

Petronić SZ, Milosavljević A, Milovanović D, Momčilović M, Radovanović Ž. Influence of picosecond laser pulses on the microstructure of austenitic materials. in Journal of Russian Laser Research. 2011;32(6):564-571.
doi:10.1007/s10946-011-9247-6 .

Petronić, Sanja Z., Milosavljević, Anđelka, Milovanović, Dubravka, Momčilović, Miloš, Radovanović, Željko, "Influence of picosecond laser pulses on the microstructure of austenitic materials" in Journal of Russian Laser Research, 32, no. 6 (2011):564-571,
https://doi.org/10.1007/s10946-011-9247-6 . .