TY  - JOUR
AU  - Marković, Snežana
AU  - Radojković, Bojana
AU  - Jegdić, Bore
AU  - Jovanović, Aleksandar
AU  - Stojanović, Jovica
AU  - Trumić, Milan
AU  - Manojlović, Vaso
PY  - 2024
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/7408
AB  - The corrosion behaviour of three types of alloys (two low-alloy carbon steel and one stainless iron with ~15 wt.% Cr), in a solution which simulates seawater (3% NaCl solution, pH 8.1) was tested. Tested samples are used to make steel (iron) balls applied in mils for grinding copper and other ore. The corrosion tests were performed using three electrochemical methods, at room temperature in the presence of atmospheric oxygen. The linear polarization resistance (LPR) method, electrochemical impedance spectroscopy (EIS) method, and linear sweep voltammetry (LSV) method were applied. Based on measurements by LPR and EIS methods (as non-destructive methods), the value of polarization resistance (Rp) was determined and the general corrosion rate (vcorr) of the examined samples was calculated. The obtained values of the general corrosion rate can be used to calculate the service life of steel (iron) balls under exploitation conditions (seawater). The appearance of the surface after linear sweep voltammetry (LSV) measurement showed the presence of localized corrosion (pits were formed) of the tested samples, especially stainless iron, and the LSV method is not suitable for the determination of the general corrosion rate of tested samples in seawater. This form of corrosion occurs at high anodic polarizations, during performing LSV measurements.
AB  - Ispitivano  je  koroziono  ponašanje  tri  vrste legura(dva  nisko-legirana  ugljenična  čelika  i  jedanuzorakje nerđajuće gvožđe sa ~15% Cr), u rastvoru koji simulira morsku vodu (3% rastvor NaCl, pH 8,1). Ispitani uzorcise koriste za proizvodnju čeličnih kugli koje se primenjuju u mlinovima za mlevenje  bakarnih  i  drugih  ruda. Koroziona  ispitivanja  su  izvedena  primenom  tri  elektrohemijske metode, na sobnoj temperaturi u prisustvu atmosferskog kiseonika. Korišćene su metoda linearne polarizacione   otpornosti   (LPR),   metoda   elektrohemijske   impedansne   spektroskopije   (EIS)   i metoda  linearne  promene  potencijala  (LSV).  Na  osnovu  merenja  LPR  i  EIS  metodama  (kao nerazarajućim  metodama),  određena  je  vrednost  polarizacione  otpornosti  (Rp),   a   zatim   je izračunata vrednost brzine opšte korozije (vkor)  ispitivanih uzoraka.  Dobijene  vrednosti  za  brzinu opšte  korozije  se  mogu  koristiti  za  izračunavanje  veka  trajanja  kugli  u  uslovima  eksploatacije (morska  voda).  Izgled  površine  ispitivanih uzorakanakon  izvođenja  LSV  metode  pokazao  je prisustvo  lokalizovane  korozije  (formirane  su  jamice,  pitovi)  na  ispitivanim uzorcima,  posebno  na nerđajućem gvožđu. Prema tome, LSV metoda nije pogodna za određivanje brzine opšte korozije ispitivanih čelika u morskoj vodi. Ovaj oblik korozije javlja se pri visokim anodnim polarizacijama tokom izvođenja LSV merenja.
PB  - Inženjersko društvo za koroziju
T2  - Zaštita materijala
T1  - Corrosion behavior of high- and low-chromium steel grinding balls in chloride solution
T1  - Koroziono ponašanje čeličnih kuglica za mlevenje sa visokim i niskim sadržajem hroma u rastvoru hlorida
EP  - 53
IS  - 1
SP  - 45
VL  - 65
DO  - 10.62638/zasmat998
ER  - 

@article{
author = "Marković, Snežana and Radojković, Bojana and Jegdić, Bore and Jovanović, Aleksandar and Stojanović, Jovica and Trumić, Milan and Manojlović, Vaso",
year = "2024",
abstract = "The corrosion behaviour of three types of alloys (two low-alloy carbon steel and one stainless iron with ~15 wt.% Cr), in a solution which simulates seawater (3% NaCl solution, pH 8.1) was tested. Tested samples are used to make steel (iron) balls applied in mils for grinding copper and other ore. The corrosion tests were performed using three electrochemical methods, at room temperature in the presence of atmospheric oxygen. The linear polarization resistance (LPR) method, electrochemical impedance spectroscopy (EIS) method, and linear sweep voltammetry (LSV) method were applied. Based on measurements by LPR and EIS methods (as non-destructive methods), the value of polarization resistance (Rp) was determined and the general corrosion rate (vcorr) of the examined samples was calculated. The obtained values of the general corrosion rate can be used to calculate the service life of steel (iron) balls under exploitation conditions (seawater). The appearance of the surface after linear sweep voltammetry (LSV) measurement showed the presence of localized corrosion (pits were formed) of the tested samples, especially stainless iron, and the LSV method is not suitable for the determination of the general corrosion rate of tested samples in seawater. This form of corrosion occurs at high anodic polarizations, during performing LSV measurements., Ispitivano  je  koroziono  ponašanje  tri  vrste legura(dva  nisko-legirana  ugljenična  čelika  i  jedanuzorakje nerđajuće gvožđe sa ~15% Cr), u rastvoru koji simulira morsku vodu (3% rastvor NaCl, pH 8,1). Ispitani uzorcise koriste za proizvodnju čeličnih kugli koje se primenjuju u mlinovima za mlevenje  bakarnih  i  drugih  ruda. Koroziona  ispitivanja  su  izvedena  primenom  tri  elektrohemijske metode, na sobnoj temperaturi u prisustvu atmosferskog kiseonika. Korišćene su metoda linearne polarizacione   otpornosti   (LPR),   metoda   elektrohemijske   impedansne   spektroskopije   (EIS)   i metoda  linearne  promene  potencijala  (LSV).  Na  osnovu  merenja  LPR  i  EIS  metodama  (kao nerazarajućim  metodama),  određena  je  vrednost  polarizacione  otpornosti  (Rp),   a   zatim   je izračunata vrednost brzine opšte korozije (vkor)  ispitivanih uzoraka.  Dobijene  vrednosti  za  brzinu opšte  korozije  se  mogu  koristiti  za  izračunavanje  veka  trajanja  kugli  u  uslovima  eksploatacije (morska  voda).  Izgled  površine  ispitivanih uzorakanakon  izvođenja  LSV  metode  pokazao  je prisustvo  lokalizovane  korozije  (formirane  su  jamice,  pitovi)  na  ispitivanim uzorcima,  posebno  na nerđajućem gvožđu. Prema tome, LSV metoda nije pogodna za određivanje brzine opšte korozije ispitivanih čelika u morskoj vodi. Ovaj oblik korozije javlja se pri visokim anodnim polarizacijama tokom izvođenja LSV merenja.",
publisher = "Inženjersko društvo za koroziju",
journal = "Zaštita materijala",
title = "Corrosion behavior of high- and low-chromium steel grinding balls in chloride solution, Koroziono ponašanje čeličnih kuglica za mlevenje sa visokim i niskim sadržajem hroma u rastvoru hlorida",
pages = "53-45",
number = "1",
volume = "65",
doi = "10.62638/zasmat998"
}

Marković, S., Radojković, B., Jegdić, B., Jovanović, A., Stojanović, J., Trumić, M.,& Manojlović, V.. (2024). Corrosion behavior of high- and low-chromium steel grinding balls in chloride solution. in Zaštita materijala
Inženjersko društvo za koroziju., 65(1), 45-53.
https://doi.org/10.62638/zasmat998

Marković S, Radojković B, Jegdić B, Jovanović A, Stojanović J, Trumić M, Manojlović V. Corrosion behavior of high- and low-chromium steel grinding balls in chloride solution. in Zaštita materijala. 2024;65(1):45-53.
doi:10.62638/zasmat998 .

Marković, Snežana, Radojković, Bojana, Jegdić, Bore, Jovanović, Aleksandar, Stojanović, Jovica, Trumić, Milan, Manojlović, Vaso, "Corrosion behavior of high- and low-chromium steel grinding balls in chloride solution" in Zaštita materijala, 65, no. 1 (2024):45-53,
https://doi.org/10.62638/zasmat998 . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Pejić, Jovanka
AU  - Marunkić, Dunja
AU  - Simović, Anđela
AU  - Eraković Pantović, Sanja
AU  - Jegdić, Bore
AU  - Bajat, Jelena
PY  - 2023
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6474
AB  - The AISI 304 (X5CrNi19-10) stainless steel is widely used for the production of various metal parts in power plants. A procedure for testing the influence of the dust from a power plant on resistance to general and pitting corrosion of the AISI 304 stainless steel is developed and performed. The quantitative (XRD method) and qualitative (Fourier–transform infrared spectroscopy [FTIR] method) composition of the dust present in the power plant is determined. Applying the Mott–Schottky method, the properties of the passive layer are analyzed, while a degree of chromium depletion of the grain boundary is determined by the electrochemical potentiokinetic reactivation method with double loop method. Values of polarization resistance (linear polarization resistance and electrochemical impedance spectroscopy methods) and the corrosion current density (polarization measurements) indicate that the stainless steel has a higher resistance to general corrosion in the dust solutions than in the etalon solution. Also, based on the measured value of the pitting potential (Epit) and the difference between the values of the pitting potential and the corrosion potential (Epit – Ecorr), it can be seen that stainless steel has a higher resistance to localized types of corrosion, such as pitting corrosion, in dust solutions than in the etalon solution.
PB  - John Wiley and Sons Inc.
T2  - Materials and Corrosion
T1  - Corrosion of metal parts in the power plant
DO  - 10.1002/maco.202313919
ER  - 

@article{
author = "Radojković, Bojana and Pejić, Jovanka and Marunkić, Dunja and Simović, Anđela and Eraković Pantović, Sanja and Jegdić, Bore and Bajat, Jelena",
year = "2023",
abstract = "The AISI 304 (X5CrNi19-10) stainless steel is widely used for the production of various metal parts in power plants. A procedure for testing the influence of the dust from a power plant on resistance to general and pitting corrosion of the AISI 304 stainless steel is developed and performed. The quantitative (XRD method) and qualitative (Fourier–transform infrared spectroscopy [FTIR] method) composition of the dust present in the power plant is determined. Applying the Mott–Schottky method, the properties of the passive layer are analyzed, while a degree of chromium depletion of the grain boundary is determined by the electrochemical potentiokinetic reactivation method with double loop method. Values of polarization resistance (linear polarization resistance and electrochemical impedance spectroscopy methods) and the corrosion current density (polarization measurements) indicate that the stainless steel has a higher resistance to general corrosion in the dust solutions than in the etalon solution. Also, based on the measured value of the pitting potential (Epit) and the difference between the values of the pitting potential and the corrosion potential (Epit – Ecorr), it can be seen that stainless steel has a higher resistance to localized types of corrosion, such as pitting corrosion, in dust solutions than in the etalon solution.",
publisher = "John Wiley and Sons Inc.",
journal = "Materials and Corrosion",
title = "Corrosion of metal parts in the power plant",
doi = "10.1002/maco.202313919"
}

Radojković, B., Pejić, J., Marunkić, D., Simović, A., Eraković Pantović, S., Jegdić, B.,& Bajat, J.. (2023). Corrosion of metal parts in the power plant. in Materials and Corrosion
John Wiley and Sons Inc...
https://doi.org/10.1002/maco.202313919

Radojković B, Pejić J, Marunkić D, Simović A, Eraković Pantović S, Jegdić B, Bajat J. Corrosion of metal parts in the power plant. in Materials and Corrosion. 2023;.
doi:10.1002/maco.202313919 .

Radojković, Bojana, Pejić, Jovanka, Marunkić, Dunja, Simović, Anđela, Eraković Pantović, Sanja, Jegdić, Bore, Bajat, Jelena, "Corrosion of metal parts in the power plant" in Materials and Corrosion (2023),
https://doi.org/10.1002/maco.202313919 . .

TY  - DATA
AU  - Radojković, Bojana
AU  - Pejić, Jovanka
AU  - Marunkić, Dunja
AU  - Simović, Anđela
AU  - Eraković Pantović, Sanja
AU  - Jegdić, Bore
AU  - Bajat, Jelena
PY  - 2023
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6475
AB  - The AISI 304 (X5CrNi19-10) stainless steel is widely used for the production of various metal parts in power plants. A procedure for testing the influence of the dust from a power plant on resistance to general and pitting corrosion of the AISI 304 stainless steel is developed and performed. The quantitative (XRD method) and qualitative (Fourier–transform infrared spectroscopy [FTIR] method) composition of the dust present in the power plant is determined. Applying the Mott–Schottky method, the properties of the passive layer are analyzed, while a degree of chromium depletion of the grain boundary is determined by the electrochemical potentiokinetic reactivation method with double loop method. Values of polarization resistance (linear polarization resistance and electrochemical impedance spectroscopy methods) and the corrosion current density (polarization measurements) indicate that the stainless steel has a higher resistance to general corrosion in the dust solutions than in the etalon solution. Also, based on the measured value of the pitting potential (Epit) and the difference between the values of the pitting potential and the corrosion potential (Epit – Ecorr), it can be seen that stainless steel has a higher resistance to localized types of corrosion, such as pitting corrosion, in dust solutions than in the etalon solution.
PB  - John Wiley and Sons Inc.
T2  - Materials and Corrosion
T1  - Supplementary material for the article: Radojković, B.; Pejić, J.; Marunkić, D.; Simović, A.; Pantović, S. E.; Jegdić, B.; Bajat, J. Corrosion of Metal Parts in the Power Plant. Materials & Corrosion 2023.  https://doi.org/10.1002/maco.202313919
UR  - https://hdl.handle.net/21.15107/rcub_technorep_6475
ER  - 

@misc{
author = "Radojković, Bojana and Pejić, Jovanka and Marunkić, Dunja and Simović, Anđela and Eraković Pantović, Sanja and Jegdić, Bore and Bajat, Jelena",
year = "2023",
abstract = "The AISI 304 (X5CrNi19-10) stainless steel is widely used for the production of various metal parts in power plants. A procedure for testing the influence of the dust from a power plant on resistance to general and pitting corrosion of the AISI 304 stainless steel is developed and performed. The quantitative (XRD method) and qualitative (Fourier–transform infrared spectroscopy [FTIR] method) composition of the dust present in the power plant is determined. Applying the Mott–Schottky method, the properties of the passive layer are analyzed, while a degree of chromium depletion of the grain boundary is determined by the electrochemical potentiokinetic reactivation method with double loop method. Values of polarization resistance (linear polarization resistance and electrochemical impedance spectroscopy methods) and the corrosion current density (polarization measurements) indicate that the stainless steel has a higher resistance to general corrosion in the dust solutions than in the etalon solution. Also, based on the measured value of the pitting potential (Epit) and the difference between the values of the pitting potential and the corrosion potential (Epit – Ecorr), it can be seen that stainless steel has a higher resistance to localized types of corrosion, such as pitting corrosion, in dust solutions than in the etalon solution.",
publisher = "John Wiley and Sons Inc.",
journal = "Materials and Corrosion",
title = "Supplementary material for the article: Radojković, B.; Pejić, J.; Marunkić, D.; Simović, A.; Pantović, S. E.; Jegdić, B.; Bajat, J. Corrosion of Metal Parts in the Power Plant. Materials & Corrosion 2023.  https://doi.org/10.1002/maco.202313919",
url = "https://hdl.handle.net/21.15107/rcub_technorep_6475"
}

Radojković, B., Pejić, J., Marunkić, D., Simović, A., Eraković Pantović, S., Jegdić, B.,& Bajat, J.. (2023). Supplementary material for the article: Radojković, B.; Pejić, J.; Marunkić, D.; Simović, A.; Pantović, S. E.; Jegdić, B.; Bajat, J. Corrosion of Metal Parts in the Power Plant. Materials & Corrosion 2023.  https://doi.org/10.1002/maco.202313919. in Materials and Corrosion
John Wiley and Sons Inc...
https://hdl.handle.net/21.15107/rcub_technorep_6475

Radojković B, Pejić J, Marunkić D, Simović A, Eraković Pantović S, Jegdić B, Bajat J. Supplementary material for the article: Radojković, B.; Pejić, J.; Marunkić, D.; Simović, A.; Pantović, S. E.; Jegdić, B.; Bajat, J. Corrosion of Metal Parts in the Power Plant. Materials & Corrosion 2023.  https://doi.org/10.1002/maco.202313919. in Materials and Corrosion. 2023;.
https://hdl.handle.net/21.15107/rcub_technorep_6475 .

Radojković, Bojana, Pejić, Jovanka, Marunkić, Dunja, Simović, Anđela, Eraković Pantović, Sanja, Jegdić, Bore, Bajat, Jelena, "Supplementary material for the article: Radojković, B.; Pejić, J.; Marunkić, D.; Simović, A.; Pantović, S. E.; Jegdić, B.; Bajat, J. Corrosion of Metal Parts in the Power Plant. Materials & Corrosion 2023.  https://doi.org/10.1002/maco.202313919" in Materials and Corrosion (2023),
https://hdl.handle.net/21.15107/rcub_technorep_6475 .

TY  - JOUR
AU  - Pejić, Jovanka
AU  - Radojković, Bojana
AU  - Marunkić, Dunja
AU  - Jegdić, Bore
AU  - Stevanović, Sanja
AU  - Milošević, Milena
AU  - Bajat, Jelena
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5171
AB  - The inhibitory effect of cysteine in the presence of selected lanthanide chlorides (LaCl3, NdCl3, and CeCl3) in a neutral 0.1 M NaCl solution was analyzed. The cysteine concentration of 0.3 mM was determined as an optimal one. The resistance to general and pitting corrosion of AA7075-T6 alloy in inhibitive solutions was determined using electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The surface appearance of the aluminum alloy was determined before and after corrosion tests using scanning electron microscopy/energy dispersive spectroscopy, while the presence of an inhibitory layer on the alloy surface was confirmed by X-ray photoelectron spectroscopy analysis and atomic force microscopy. The inhibitory effect of cysteine was significantly higher in the presence of all tested lanthanide chlorides, especially to pitting corrosion. The protective ability of cysteine was increased by lanthanides in the following sequence: Ln < Nd < Ce ions. The inhibitory effect of cysteine in the presence of cerium ions was examined in more detail as cerium ions provided the highest inhibitory effect, both to general and pitting corrosion.
PB  - John Wiley and Sons Inc
T2  - Materials and Corrosion
T1  - Inhibitory effect of cysteine and lanthanides on AA7075-T6 in neutral NaCl solution
DO  - 10.1002/maco.202213330
ER  - 

@article{
author = "Pejić, Jovanka and Radojković, Bojana and Marunkić, Dunja and Jegdić, Bore and Stevanović, Sanja and Milošević, Milena and Bajat, Jelena",
year = "2022",
abstract = "The inhibitory effect of cysteine in the presence of selected lanthanide chlorides (LaCl3, NdCl3, and CeCl3) in a neutral 0.1 M NaCl solution was analyzed. The cysteine concentration of 0.3 mM was determined as an optimal one. The resistance to general and pitting corrosion of AA7075-T6 alloy in inhibitive solutions was determined using electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The surface appearance of the aluminum alloy was determined before and after corrosion tests using scanning electron microscopy/energy dispersive spectroscopy, while the presence of an inhibitory layer on the alloy surface was confirmed by X-ray photoelectron spectroscopy analysis and atomic force microscopy. The inhibitory effect of cysteine was significantly higher in the presence of all tested lanthanide chlorides, especially to pitting corrosion. The protective ability of cysteine was increased by lanthanides in the following sequence: Ln < Nd < Ce ions. The inhibitory effect of cysteine in the presence of cerium ions was examined in more detail as cerium ions provided the highest inhibitory effect, both to general and pitting corrosion.",
publisher = "John Wiley and Sons Inc",
journal = "Materials and Corrosion",
title = "Inhibitory effect of cysteine and lanthanides on AA7075-T6 in neutral NaCl solution",
doi = "10.1002/maco.202213330"
}

Pejić, J., Radojković, B., Marunkić, D., Jegdić, B., Stevanović, S., Milošević, M.,& Bajat, J.. (2022). Inhibitory effect of cysteine and lanthanides on AA7075-T6 in neutral NaCl solution. in Materials and Corrosion
John Wiley and Sons Inc..
https://doi.org/10.1002/maco.202213330

Pejić J, Radojković B, Marunkić D, Jegdić B, Stevanović S, Milošević M, Bajat J. Inhibitory effect of cysteine and lanthanides on AA7075-T6 in neutral NaCl solution. in Materials and Corrosion. 2022;.
doi:10.1002/maco.202213330 .

Pejić, Jovanka, Radojković, Bojana, Marunkić, Dunja, Jegdić, Bore, Stevanović, Sanja, Milošević, Milena, Bajat, Jelena, "Inhibitory effect of cysteine and lanthanides on AA7075-T6 in neutral NaCl solution" in Materials and Corrosion (2022),
https://doi.org/10.1002/maco.202213330 . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Marunkić, Dunja
AU  - Milošević, Milena
AU  - Grubišić, Sonja
AU  - Pejić, Jovanka
AU  - Jegdić, Bore
AU  - Marinković, Aleksandar
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5134
AB  - Green corrosion inhibitors, Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate, were tested in NaCl solution with the aim to evaluate their inhibitory effect on 7049 aluminum alloy and to propose a mechanism of their inhibitive action. Corrosion properties of the formed inhibitor layer were analyzed using electrochemical impedance spectroscopy, while the pit formation resistance was analyzed using potentiodynamic polarization tests. Morphology of the formed pits was evaluated by scanning electron microscope/energy-dispersive spectroscopy analysis. It was shown that Ce(III) propionate in NaCl solution has a noticeably higher protective ability than Ce(III) chloride and Ce(III) nitrate. The presence of cerium, propionate anions, and Al–O bonds in the inhibitive layer on the 7049 aluminum alloy surface was confirmed by X-ray photoelectron spectroscopy analysis. This indicates the formation of Ce propionate complexes and bonds via oxygen atoms from carboxylate anions with the metal surface. Density-functional theory methods were used for the geometry optimization of possible Ce propionate complexes as corrosion inhibitors.
PB  - John Wiley and Sons Inc
T2  - Materials and Corrosion
T1  - Analysis of the Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate as corrosion inhibitor of the aluminum alloys in NaCl solution
DO  - 10.1002/maco.202213177
ER  - 

@article{
author = "Radojković, Bojana and Marunkić, Dunja and Milošević, Milena and Grubišić, Sonja and Pejić, Jovanka and Jegdić, Bore and Marinković, Aleksandar",
year = "2022",
abstract = "Green corrosion inhibitors, Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate, were tested in NaCl solution with the aim to evaluate their inhibitory effect on 7049 aluminum alloy and to propose a mechanism of their inhibitive action. Corrosion properties of the formed inhibitor layer were analyzed using electrochemical impedance spectroscopy, while the pit formation resistance was analyzed using potentiodynamic polarization tests. Morphology of the formed pits was evaluated by scanning electron microscope/energy-dispersive spectroscopy analysis. It was shown that Ce(III) propionate in NaCl solution has a noticeably higher protective ability than Ce(III) chloride and Ce(III) nitrate. The presence of cerium, propionate anions, and Al–O bonds in the inhibitive layer on the 7049 aluminum alloy surface was confirmed by X-ray photoelectron spectroscopy analysis. This indicates the formation of Ce propionate complexes and bonds via oxygen atoms from carboxylate anions with the metal surface. Density-functional theory methods were used for the geometry optimization of possible Ce propionate complexes as corrosion inhibitors.",
publisher = "John Wiley and Sons Inc",
journal = "Materials and Corrosion",
title = "Analysis of the Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate as corrosion inhibitor of the aluminum alloys in NaCl solution",
doi = "10.1002/maco.202213177"
}

Radojković, B., Marunkić, D., Milošević, M., Grubišić, S., Pejić, J., Jegdić, B.,& Marinković, A.. (2022). Analysis of the Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate as corrosion inhibitor of the aluminum alloys in NaCl solution. in Materials and Corrosion
John Wiley and Sons Inc..
https://doi.org/10.1002/maco.202213177

Radojković B, Marunkić D, Milošević M, Grubišić S, Pejić J, Jegdić B, Marinković A. Analysis of the Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate as corrosion inhibitor of the aluminum alloys in NaCl solution. in Materials and Corrosion. 2022;.
doi:10.1002/maco.202213177 .

Radojković, Bojana, Marunkić, Dunja, Milošević, Milena, Grubišić, Sonja, Pejić, Jovanka, Jegdić, Bore, Marinković, Aleksandar, "Analysis of the Ce(III) chloride, Ce(III) nitrate, and Ce(III) propionate as corrosion inhibitor of the aluminum alloys in NaCl solution" in Materials and Corrosion (2022),
https://doi.org/10.1002/maco.202213177 . .

TY  - JOUR
AU  - Marunkić, Dunja
AU  - Jegdić, Bore
AU  - Pejić, Jovanka
AU  - Milošević, Milena
AU  - Marinković, Aleksandar
AU  - Radojković, Bojana
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5083
AB  - The new environmentally friendly corrosion inhibitor Ce-citrate was analyzed in 0.05 M NaCl solution on the AISI 4130 steel. For comparison, corrosion inhibitor Ce-chloride is tested in the same concentration as Ce-citrate (0.3 mM). Inhibitor efficiencies were determined by applying electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results of electrochemical measurements, the contact angle measurements, as well as the surface appearance of the specimens after the immersion in the inhibitive NaCl solution for 96 h confirmed that the new environmentally friendly inhibitor (Ce-citrate) has a significantly higher protective ability than the Ce-chloride. The protective ability of Ce-citrate increases over time, according to the proposed mechanism of its action. In the inhibitive layer formed in NaCl solution containing Ce-citrate, XPS analysis revealed the presence of cerium in oxidation states CeIII and CeIV, citrate anions (carboxyl O–C═O group as well as C–OH and C–C and C–H bonds), oxide, hydroxide, and oxyhydroxide of iron (mainly FeOOH and Fe2O3). The mechanism of inhibitory action of Ce-citrate was proposed and analyzed in detail.
PB  - John Wiley and Sons Inc
T2  - Materials and Corrosion
T1  - Analysis of inhibitory properties of Ce-citrate as a green corrosion inhibitor of low alloy steel in neutral chloride solution
DO  - 10.1002/maco.202213079
ER  - 

@article{
author = "Marunkić, Dunja and Jegdić, Bore and Pejić, Jovanka and Milošević, Milena and Marinković, Aleksandar and Radojković, Bojana",
year = "2022",
abstract = "The new environmentally friendly corrosion inhibitor Ce-citrate was analyzed in 0.05 M NaCl solution on the AISI 4130 steel. For comparison, corrosion inhibitor Ce-chloride is tested in the same concentration as Ce-citrate (0.3 mM). Inhibitor efficiencies were determined by applying electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results of electrochemical measurements, the contact angle measurements, as well as the surface appearance of the specimens after the immersion in the inhibitive NaCl solution for 96 h confirmed that the new environmentally friendly inhibitor (Ce-citrate) has a significantly higher protective ability than the Ce-chloride. The protective ability of Ce-citrate increases over time, according to the proposed mechanism of its action. In the inhibitive layer formed in NaCl solution containing Ce-citrate, XPS analysis revealed the presence of cerium in oxidation states CeIII and CeIV, citrate anions (carboxyl O–C═O group as well as C–OH and C–C and C–H bonds), oxide, hydroxide, and oxyhydroxide of iron (mainly FeOOH and Fe2O3). The mechanism of inhibitory action of Ce-citrate was proposed and analyzed in detail.",
publisher = "John Wiley and Sons Inc",
journal = "Materials and Corrosion",
title = "Analysis of inhibitory properties of Ce-citrate as a green corrosion inhibitor of low alloy steel in neutral chloride solution",
doi = "10.1002/maco.202213079"
}

Marunkić, D., Jegdić, B., Pejić, J., Milošević, M., Marinković, A.,& Radojković, B.. (2022). Analysis of inhibitory properties of Ce-citrate as a green corrosion inhibitor of low alloy steel in neutral chloride solution. in Materials and Corrosion
John Wiley and Sons Inc..
https://doi.org/10.1002/maco.202213079

Marunkić D, Jegdić B, Pejić J, Milošević M, Marinković A, Radojković B. Analysis of inhibitory properties of Ce-citrate as a green corrosion inhibitor of low alloy steel in neutral chloride solution. in Materials and Corrosion. 2022;.
doi:10.1002/maco.202213079 .

Marunkić, Dunja, Jegdić, Bore, Pejić, Jovanka, Milošević, Milena, Marinković, Aleksandar, Radojković, Bojana, "Analysis of inhibitory properties of Ce-citrate as a green corrosion inhibitor of low alloy steel in neutral chloride solution" in Materials and Corrosion (2022),
https://doi.org/10.1002/maco.202213079 . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Kovačina, Jovanka
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Alić, Behar
AU  - Marunkić, Dunja D.
AU  - Simović, Anđela
PY  - 2021
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/8
AB  - This study considers the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint in NaCl solution, with and without the presence of several corrosion inhibitors (NaNO3, Ce(NO3)(3), and CeCl3). The degree of sensitization of the welded joint to intergranular corrosion is determined using the electrochemical potentiokinetic reactivation method with a double-loop method. Pitting corrosion tests are performed by the potentiodynamic method. Resistance to general corrosion and the stability of the passive film is assessed based on the results of electrochemical impedance spectroscopy measurements, as well as on the values of the corrosion and passivation current. The main goal of this study is to determine the relation of the welded joint microstructure to general and pitting corrosion in the presence of the corrosion inhibitors. The value of pitting potential for the base metal and weld metal in the presence of the NaNO3 or Ce(NO3)(3) inhibitor is shifted to potentials in the transpassive area. The pitting potential for the heat-affected zone also possesses a noticeable higher value. However, nitrate ions do not increase the general corrosion resistance of any part of the welded joint. CeCl3 does not increase resistance to general or pitting corrosion.
PB  - Wiley-VCH Verlag Gmbh, Weinheim
T2  - Materials and Corrosion-Werkstoffe Und Korrosion
T1  - Influence of inhibitors on the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint
EP  - 707
IS  - 4
SP  - 694
VL  - 72
DO  - 10.1002/maco.202012039
ER  - 

@article{
author = "Radojković, Bojana and Kovačina, Jovanka and Jegdić, Bore and Bobić, Biljana and Alić, Behar and Marunkić, Dunja D. and Simović, Anđela",
year = "2021",
abstract = "This study considers the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint in NaCl solution, with and without the presence of several corrosion inhibitors (NaNO3, Ce(NO3)(3), and CeCl3). The degree of sensitization of the welded joint to intergranular corrosion is determined using the electrochemical potentiokinetic reactivation method with a double-loop method. Pitting corrosion tests are performed by the potentiodynamic method. Resistance to general corrosion and the stability of the passive film is assessed based on the results of electrochemical impedance spectroscopy measurements, as well as on the values of the corrosion and passivation current. The main goal of this study is to determine the relation of the welded joint microstructure to general and pitting corrosion in the presence of the corrosion inhibitors. The value of pitting potential for the base metal and weld metal in the presence of the NaNO3 or Ce(NO3)(3) inhibitor is shifted to potentials in the transpassive area. The pitting potential for the heat-affected zone also possesses a noticeable higher value. However, nitrate ions do not increase the general corrosion resistance of any part of the welded joint. CeCl3 does not increase resistance to general or pitting corrosion.",
publisher = "Wiley-VCH Verlag Gmbh, Weinheim",
journal = "Materials and Corrosion-Werkstoffe Und Korrosion",
title = "Influence of inhibitors on the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint",
pages = "707-694",
number = "4",
volume = "72",
doi = "10.1002/maco.202012039"
}

Radojković, B., Kovačina, J., Jegdić, B., Bobić, B., Alić, B., Marunkić, D. D.,& Simović, A.. (2021). Influence of inhibitors on the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint. in Materials and Corrosion-Werkstoffe Und Korrosion
Wiley-VCH Verlag Gmbh, Weinheim., 72(4), 694-707.
https://doi.org/10.1002/maco.202012039

Radojković B, Kovačina J, Jegdić B, Bobić B, Alić B, Marunkić DD, Simović A. Influence of inhibitors on the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint. in Materials and Corrosion-Werkstoffe Und Korrosion. 2021;72(4):694-707.
doi:10.1002/maco.202012039 .

Radojković, Bojana, Kovačina, Jovanka, Jegdić, Bore, Bobić, Biljana, Alić, Behar, Marunkić, Dunja D., Simović, Anđela, "Influence of inhibitors on the corrosion behavior of the X5CrNi18 10 stainless steel-welded joint" in Materials and Corrosion-Werkstoffe Und Korrosion, 72, no. 4 (2021):694-707,
https://doi.org/10.1002/maco.202012039 . .

TY  - CONF
AU  - Kovačina, Jovanka N.
AU  - Marunkić, Dunja D.
AU  - Simović, Anđela
AU  - Radojković, Bojana
AU  - Jegdić, Bore
AU  - Marinković, Aleksandar
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4409
AB  - Aluminium AA7075 alloy with its low density and good mechanical properties, widely responds to the requirements of aerospace, navy, and defense industries. However, corrosion is the most common problem that affects the reliability and service life of components and constructions based on this alloy. One of the most practical methods for protecting metals from corrosion is the use of inhibitors. Chromates are known as excellent inhibitors but chromate compounds are highly toxic, carcinogenic, and thus hazardous to humans and the environment. The aim of this study was to synthesize an organic eco-friendly compound (cerium-cysteine) and to investigate its inhibitory property on aluminum alloy AA7075-T6. Rare-earth metals are effective and environmentally friendly substances for aluminium protection as well as cysteine that can be found in many proteins and enzymes such as the keratin in hair. The synthesized inhibitor was confirmed and analyzed by FTIR. The survey of samples corrosion resistance was conducted by three electrochemical methods: linear polarization resistance (LPR), electrochemical impedance spectroscopy (EIS), and polarization measurements (Epit) in a 0.1M NaCl solution at room temperature. Different concentrations of ceriumcysteine were used to find the best efficiency. The best results were then tested for time dependence (up to 72 h). The inhibitory effectiveness of the cerium complex is shown to depend on a variety of factors such as concentration and time dependence.
PB  - Belgrade : Military Technical Institute
C3  - 9th International Scientific Conference od Defensive Technologies OTEH 2020
T1  - Cerium-cysteine complex inhibitor for aluminium alloy AA7075-T6
UR  - https://hdl.handle.net/21.15107/rcub_technorep_4409
ER  - 

@conference{
author = "Kovačina, Jovanka N. and Marunkić, Dunja D. and Simović, Anđela and Radojković, Bojana and Jegdić, Bore and Marinković, Aleksandar",
year = "2020",
abstract = "Aluminium AA7075 alloy with its low density and good mechanical properties, widely responds to the requirements of aerospace, navy, and defense industries. However, corrosion is the most common problem that affects the reliability and service life of components and constructions based on this alloy. One of the most practical methods for protecting metals from corrosion is the use of inhibitors. Chromates are known as excellent inhibitors but chromate compounds are highly toxic, carcinogenic, and thus hazardous to humans and the environment. The aim of this study was to synthesize an organic eco-friendly compound (cerium-cysteine) and to investigate its inhibitory property on aluminum alloy AA7075-T6. Rare-earth metals are effective and environmentally friendly substances for aluminium protection as well as cysteine that can be found in many proteins and enzymes such as the keratin in hair. The synthesized inhibitor was confirmed and analyzed by FTIR. The survey of samples corrosion resistance was conducted by three electrochemical methods: linear polarization resistance (LPR), electrochemical impedance spectroscopy (EIS), and polarization measurements (Epit) in a 0.1M NaCl solution at room temperature. Different concentrations of ceriumcysteine were used to find the best efficiency. The best results were then tested for time dependence (up to 72 h). The inhibitory effectiveness of the cerium complex is shown to depend on a variety of factors such as concentration and time dependence.",
publisher = "Belgrade : Military Technical Institute",
journal = "9th International Scientific Conference od Defensive Technologies OTEH 2020",
title = "Cerium-cysteine complex inhibitor for aluminium alloy AA7075-T6",
url = "https://hdl.handle.net/21.15107/rcub_technorep_4409"
}

Kovačina, J. N., Marunkić, D. D., Simović, A., Radojković, B., Jegdić, B.,& Marinković, A.. (2020). Cerium-cysteine complex inhibitor for aluminium alloy AA7075-T6. in 9th International Scientific Conference od Defensive Technologies OTEH 2020
Belgrade : Military Technical Institute..
https://hdl.handle.net/21.15107/rcub_technorep_4409

Kovačina JN, Marunkić DD, Simović A, Radojković B, Jegdić B, Marinković A. Cerium-cysteine complex inhibitor for aluminium alloy AA7075-T6. in 9th International Scientific Conference od Defensive Technologies OTEH 2020. 2020;.
https://hdl.handle.net/21.15107/rcub_technorep_4409 .

Kovačina, Jovanka N., Marunkić, Dunja D., Simović, Anđela, Radojković, Bojana, Jegdić, Bore, Marinković, Aleksandar, "Cerium-cysteine complex inhibitor for aluminium alloy AA7075-T6" in 9th International Scientific Conference od Defensive Technologies OTEH 2020 (2020),
https://hdl.handle.net/21.15107/rcub_technorep_4409 .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Stevanović, Maja
AU  - Mihailović, Marija
AU  - Daničić, Dunja
AU  - Kovačina, Jovanka
AU  - Radojković, Bojana
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4533
AB  - The paper analyses the corrosion behaviour of both naturally and artificially aged AA2024 aluminium alloy in NaCl solution in the presence of the corrosion inhibitor benzotriazole (BTA). The differences between these two aging tempers in terms of resistance to general corrosion are explained as well as the differences in terms of pit formation and pit growth. Based on the values of the polarisation resistance and the corrosion current density, the general corrosion resistance of the alloy is determined in the absence and in the presence of BTA. The resistance to pit formation and pit growth is determined on the basis of the polarisation measurements results. Scanning electron microscopy confirmed the expected differences in the appearance and size of the pits formed in naturally aged and artificially aged alloy. In the presence of the corrosion inhibitor BTA, for both aging tempers of the alloy, the corrosion resistance is significantly higher compared to the resistance in the solution without the inhibitor. The value of the polarisation resistance for both aging tempers increases over time. However, at the same time, the value of the constant phase element increases as well. An explanation for this phenomenon is provided. The calculated average value of the thickness of the adsorbed inhibitor layer on the surface of the aluminium alloy is in accordance with the inhibitor protective ability for both aging tempers. Graphic
PB  - Korean Inst Metals Materials, Seoul
T2  - Metals and Materials International
T1  - Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole
EP  - 1653
IS  - 11
SP  - 1643
VL  - 26
DO  - 10.1007/s12540-019-00451-8
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Stevanović, Maja and Mihailović, Marija and Daničić, Dunja and Kovačina, Jovanka and Radojković, Bojana",
year = "2020",
abstract = "The paper analyses the corrosion behaviour of both naturally and artificially aged AA2024 aluminium alloy in NaCl solution in the presence of the corrosion inhibitor benzotriazole (BTA). The differences between these two aging tempers in terms of resistance to general corrosion are explained as well as the differences in terms of pit formation and pit growth. Based on the values of the polarisation resistance and the corrosion current density, the general corrosion resistance of the alloy is determined in the absence and in the presence of BTA. The resistance to pit formation and pit growth is determined on the basis of the polarisation measurements results. Scanning electron microscopy confirmed the expected differences in the appearance and size of the pits formed in naturally aged and artificially aged alloy. In the presence of the corrosion inhibitor BTA, for both aging tempers of the alloy, the corrosion resistance is significantly higher compared to the resistance in the solution without the inhibitor. The value of the polarisation resistance for both aging tempers increases over time. However, at the same time, the value of the constant phase element increases as well. An explanation for this phenomenon is provided. The calculated average value of the thickness of the adsorbed inhibitor layer on the surface of the aluminium alloy is in accordance with the inhibitor protective ability for both aging tempers. Graphic",
publisher = "Korean Inst Metals Materials, Seoul",
journal = "Metals and Materials International",
title = "Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole",
pages = "1653-1643",
number = "11",
volume = "26",
doi = "10.1007/s12540-019-00451-8"
}

Jegdić, B., Bobić, B., Stevanović, M., Mihailović, M., Daničić, D., Kovačina, J.,& Radojković, B.. (2020). Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole. in Metals and Materials International
Korean Inst Metals Materials, Seoul., 26(11), 1643-1653.
https://doi.org/10.1007/s12540-019-00451-8

Jegdić B, Bobić B, Stevanović M, Mihailović M, Daničić D, Kovačina J, Radojković B. Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole. in Metals and Materials International. 2020;26(11):1643-1653.
doi:10.1007/s12540-019-00451-8 .

Jegdić, Bore, Bobić, Biljana, Stevanović, Maja, Mihailović, Marija, Daničić, Dunja, Kovačina, Jovanka, Radojković, Bojana, "Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole" in Metals and Materials International, 26, no. 11 (2020):1643-1653,
https://doi.org/10.1007/s12540-019-00451-8 . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Ristić, Slavica S.
AU  - Polić, Suzana
AU  - Jančić-Heinemann, Radmila
AU  - Radovanović, Danijelka
PY  - 2017
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3693
AB  - The classic methods of cleaning old-fashioned textile museum objects with metallic yarns do not often yield expected results. The use of laser in the conservation of these objects plays an important role as a very efficient and ecologically friendly technique. Conservation and restoration of historical exhibits with metal-textile combinations is becoming ever more complex due to a huge variety of damaging factors. The paper presents the results of the corrosion laser cleaning effects on ethnographic textile with silver coated copper yarns from the holdings of the Ethnographic Museum in Belgrade, using Nd:YAG laser. The testing of the cleaning effects was performed by optical and scanning electron microscopy. The chemical analysis of yarns was done by the EDX and XRD analyses. The parameters for successful and safe cleaning of corrosion products on metallic yarns were determined.
PB  - Elsevier France-Editions Scientifiques Medicales Elsevier, Paris
T2  - Journal of Cultural Heritage
T1  - Preliminary investigation on the use of the Q-switched Nd:YAG laser to clean corrosion products on museum embroidered textiles with metallic yarns
EP  - 137
SP  - 128
VL  - 23
DO  - 10.1016/j.culher.2016.07.001
ER  - 

@article{
author = "Radojković, Bojana and Ristić, Slavica S. and Polić, Suzana and Jančić-Heinemann, Radmila and Radovanović, Danijelka",
year = "2017",
abstract = "The classic methods of cleaning old-fashioned textile museum objects with metallic yarns do not often yield expected results. The use of laser in the conservation of these objects plays an important role as a very efficient and ecologically friendly technique. Conservation and restoration of historical exhibits with metal-textile combinations is becoming ever more complex due to a huge variety of damaging factors. The paper presents the results of the corrosion laser cleaning effects on ethnographic textile with silver coated copper yarns from the holdings of the Ethnographic Museum in Belgrade, using Nd:YAG laser. The testing of the cleaning effects was performed by optical and scanning electron microscopy. The chemical analysis of yarns was done by the EDX and XRD analyses. The parameters for successful and safe cleaning of corrosion products on metallic yarns were determined.",
publisher = "Elsevier France-Editions Scientifiques Medicales Elsevier, Paris",
journal = "Journal of Cultural Heritage",
title = "Preliminary investigation on the use of the Q-switched Nd:YAG laser to clean corrosion products on museum embroidered textiles with metallic yarns",
pages = "137-128",
volume = "23",
doi = "10.1016/j.culher.2016.07.001"
}

Radojković, B., Ristić, S. S., Polić, S., Jančić-Heinemann, R.,& Radovanović, D.. (2017). Preliminary investigation on the use of the Q-switched Nd:YAG laser to clean corrosion products on museum embroidered textiles with metallic yarns. in Journal of Cultural Heritage
Elsevier France-Editions Scientifiques Medicales Elsevier, Paris., 23, 128-137.
https://doi.org/10.1016/j.culher.2016.07.001

Radojković B, Ristić SS, Polić S, Jančić-Heinemann R, Radovanović D. Preliminary investigation on the use of the Q-switched Nd:YAG laser to clean corrosion products on museum embroidered textiles with metallic yarns. in Journal of Cultural Heritage. 2017;23:128-137.
doi:10.1016/j.culher.2016.07.001 .

Radojković, Bojana, Ristić, Slavica S., Polić, Suzana, Jančić-Heinemann, Radmila, Radovanović, Danijelka, "Preliminary investigation on the use of the Q-switched Nd:YAG laser to clean corrosion products on museum embroidered textiles with metallic yarns" in Journal of Cultural Heritage, 23 (2017):128-137,
https://doi.org/10.1016/j.culher.2016.07.001 . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Ristić, Slavica
AU  - Polić, Suzana
AU  - Jančić-Heinemann, Radmila
PY  - 2017
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3498
AB  - The main aim of this paper is to present the results of the morphological and chemical changes on the surface of a ceramic sample irradiated by the Nd:YAG laser. The tested sample is a part of an aqueduct tile, originating from the archaeological site of Yazd, Iran. The laser irradiation effects were studied as a function of the number of laser pulses and laser fluences around and over the damage threshold. The obtained modifications were investigated because these are essential in laser cleaning of aqueduct ceramics. The Nd: YAG laser with a wavelength, lambda, of 1064 nm and full width at half maximum (FWHM) pulse, tau, of 150 ps has been used for the surface treatment. The ceramic surface morphology modifications, induced by laser, were characterized by a scanning electron microscope (SEM), while the composition was examined by energy-dispersive (EDX) and X-ray fluorescence (XRF) spectroscopy. The results show that there are significant differences depending on the applied laser fluences and whether the surface is glazed or not.
T2  - Lasers in Engineering
T1  - Surface Modification of Aqueduct Ceramics Induced By Nd:YAG Pulsed Laser Treatment
EP  - 390
IS  - 4-6
SP  - 373
VL  - 36
UR  - https://hdl.handle.net/21.15107/rcub_technorep_3498
ER  - 

@article{
author = "Radojković, Bojana and Ristić, Slavica and Polić, Suzana and Jančić-Heinemann, Radmila",
year = "2017",
abstract = "The main aim of this paper is to present the results of the morphological and chemical changes on the surface of a ceramic sample irradiated by the Nd:YAG laser. The tested sample is a part of an aqueduct tile, originating from the archaeological site of Yazd, Iran. The laser irradiation effects were studied as a function of the number of laser pulses and laser fluences around and over the damage threshold. The obtained modifications were investigated because these are essential in laser cleaning of aqueduct ceramics. The Nd: YAG laser with a wavelength, lambda, of 1064 nm and full width at half maximum (FWHM) pulse, tau, of 150 ps has been used for the surface treatment. The ceramic surface morphology modifications, induced by laser, were characterized by a scanning electron microscope (SEM), while the composition was examined by energy-dispersive (EDX) and X-ray fluorescence (XRF) spectroscopy. The results show that there are significant differences depending on the applied laser fluences and whether the surface is glazed or not.",
journal = "Lasers in Engineering",
title = "Surface Modification of Aqueduct Ceramics Induced By Nd:YAG Pulsed Laser Treatment",
pages = "390-373",
number = "4-6",
volume = "36",
url = "https://hdl.handle.net/21.15107/rcub_technorep_3498"
}

Radojković, B., Ristić, S., Polić, S.,& Jančić-Heinemann, R.. (2017). Surface Modification of Aqueduct Ceramics Induced By Nd:YAG Pulsed Laser Treatment. in Lasers in Engineering, 36(4-6), 373-390.
https://hdl.handle.net/21.15107/rcub_technorep_3498

Radojković B, Ristić S, Polić S, Jančić-Heinemann R. Surface Modification of Aqueduct Ceramics Induced By Nd:YAG Pulsed Laser Treatment. in Lasers in Engineering. 2017;36(4-6):373-390.
https://hdl.handle.net/21.15107/rcub_technorep_3498 .

Radojković, Bojana, Ristić, Slavica, Polić, Suzana, Jančić-Heinemann, Radmila, "Surface Modification of Aqueduct Ceramics Induced By Nd:YAG Pulsed Laser Treatment" in Lasers in Engineering, 36, no. 4-6 (2017):373-390,
https://hdl.handle.net/21.15107/rcub_technorep_3498 .

TY  - JOUR
AU  - Ristić, Slavica
AU  - Polić, Suzana
AU  - Radojković, Bojana
AU  - Zrilić, Milorad
AU  - Jančić-Heinemann, Radmila
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2620
AB  - This paper presents the results of the laser cleaning effects on textile samples with corroded metallic threads. In many museum collections, there are textile exhibits like uniforms, national costumes, flags and home textile, embroidered with metallic threads. Corrosion of metal threads is one of the most common problems that damage embroidered items. In the practice, the application of conventional cleaning methods rarely gives the expected results, and the implementation of laser technology was the next step for corrosion products cleaning. The Nd: YAG laser was used to clean the corrosion of embroidered items from a museum study collection. The effects on the laser irradiated zones were investigated by optical and SEM microscopy and the EDX analysis. The laser irradiation process parameters of the metal threads corrosion.
AB  - U radu su prikazani rezultati čišćenja korozije na tekstilnim eksponatima sa metalnim nitima pomoću lasera. U mnogim muzejskim zbirkama nalaze se eksponati kao što su uniforme, narodne nošnje, zastave i kućni tekstil, ukrašeni vezom metalnim nitima. Korozija metalnih niti je jedan od najvećih problema, koji oštećuje vezene eksponate. U praksi, veoma često, klasične metode ne daju očekivane rezultate i primena lasera je sledeći korak čišćenja korozionih produkata. Nd- YAG laser je korišćen za čišćenje korozije vezenih eksponata iz muzejske, studijske zbirke. Efekti u zonama ozračenim laserom su ispitivani optičkim mikroskopom, SEMom i EDX analizom. Određeni su izabrani parametri za uspešno i bezbedno čišćenje korozije na metalnim nitima.
PB  - Military Technical Institute, Belgrade
T2  - Scientific Technical Review
T1  - Laser cleaning of textile artifacts with metal threads: Process parameter optimization
T1  - Lasersko čišćenje tekstilnih eksponata sa korodiranim metalnim nitima - optimzacije parametara procesa
EP  - 52
IS  - 4
SP  - 45
VL  - 64
UR  - https://hdl.handle.net/21.15107/rcub_cer_5495
ER  - 

@article{
author = "Ristić, Slavica and Polić, Suzana and Radojković, Bojana and Zrilić, Milorad and Jančić-Heinemann, Radmila",
year = "2014",
abstract = "This paper presents the results of the laser cleaning effects on textile samples with corroded metallic threads. In many museum collections, there are textile exhibits like uniforms, national costumes, flags and home textile, embroidered with metallic threads. Corrosion of metal threads is one of the most common problems that damage embroidered items. In the practice, the application of conventional cleaning methods rarely gives the expected results, and the implementation of laser technology was the next step for corrosion products cleaning. The Nd: YAG laser was used to clean the corrosion of embroidered items from a museum study collection. The effects on the laser irradiated zones were investigated by optical and SEM microscopy and the EDX analysis. The laser irradiation process parameters of the metal threads corrosion., U radu su prikazani rezultati čišćenja korozije na tekstilnim eksponatima sa metalnim nitima pomoću lasera. U mnogim muzejskim zbirkama nalaze se eksponati kao što su uniforme, narodne nošnje, zastave i kućni tekstil, ukrašeni vezom metalnim nitima. Korozija metalnih niti je jedan od najvećih problema, koji oštećuje vezene eksponate. U praksi, veoma često, klasične metode ne daju očekivane rezultate i primena lasera je sledeći korak čišćenja korozionih produkata. Nd- YAG laser je korišćen za čišćenje korozije vezenih eksponata iz muzejske, studijske zbirke. Efekti u zonama ozračenim laserom su ispitivani optičkim mikroskopom, SEMom i EDX analizom. Određeni su izabrani parametri za uspešno i bezbedno čišćenje korozije na metalnim nitima.",
publisher = "Military Technical Institute, Belgrade",
journal = "Scientific Technical Review",
title = "Laser cleaning of textile artifacts with metal threads: Process parameter optimization, Lasersko čišćenje tekstilnih eksponata sa korodiranim metalnim nitima - optimzacije parametara procesa",
pages = "52-45",
number = "4",
volume = "64",
url = "https://hdl.handle.net/21.15107/rcub_cer_5495"
}

Ristić, S., Polić, S., Radojković, B., Zrilić, M.,& Jančić-Heinemann, R.. (2014). Laser cleaning of textile artifacts with metal threads: Process parameter optimization. in Scientific Technical Review
Military Technical Institute, Belgrade., 64(4), 45-52.
https://hdl.handle.net/21.15107/rcub_cer_5495

Ristić S, Polić S, Radojković B, Zrilić M, Jančić-Heinemann R. Laser cleaning of textile artifacts with metal threads: Process parameter optimization. in Scientific Technical Review. 2014;64(4):45-52.
https://hdl.handle.net/21.15107/rcub_cer_5495 .

Ristić, Slavica, Polić, Suzana, Radojković, Bojana, Zrilić, Milorad, Jančić-Heinemann, Radmila, "Laser cleaning of textile artifacts with metal threads: Process parameter optimization" in Scientific Technical Review, 64, no. 4 (2014):45-52,
https://hdl.handle.net/21.15107/rcub_cer_5495 .