TY  - JOUR
AU  - Rubinjoni, Luka
AU  - Stanković, Srboljub J.
AU  - Lončar, Boris
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4432
AB  - Cementation is the baseline technology for conditioning of low to intermediate level radioactive waste. Geopolymers, a class of alkali activated binders, are a promising new material for radioactive waste treatment. Coal fly-ash based geopolymers are a low-cost, low greenhouse gas footprint alternative to metakaolin based materials. Both the grouting of sludge/powders/liquids and encapsulation of solids/compacted waste rely on the grout maintaining optimal flow (theological properties) during the mixing and pouring operations, and achieving a set leading to proper long term solidification (mechanical properties). The initial and final setting time for fly-ash geopolymer paste, based on the SRPS EN 196-3 standard, has been measured upon irradiation by gamma rays in a Co-60 reference field positioned with a kerma air rate of 3.42 mGys(-1). The binder paste was prepared using fly-ash from the TENT B power plant's electrostatic filters without further sieving, activated by water glass with module 1.5 and mixed with distilled water until a satisfactory flow was obtained, and poured into the sample and control molds. The initial and final setting times for the irradiated sample and non-irradiated control were determined by the Vicat apparatus. The irradiated sample demonstrated an 11 % shorter initial setting time, and 16 % shorter final setting time, compared to the control.
PB  - Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd
T2  - Nuclear Technology & Radiation Protection
T1  - The effect of co-60 gamma irradiation on coal fly-ash geopolymer paste setting time
EP  - 153
IS  - 2
SP  - 150
VL  - 35
DO  - 10.2298/NTRP2002150R
ER  - 

@article{
author = "Rubinjoni, Luka and Stanković, Srboljub J. and Lončar, Boris",
year = "2020",
abstract = "Cementation is the baseline technology for conditioning of low to intermediate level radioactive waste. Geopolymers, a class of alkali activated binders, are a promising new material for radioactive waste treatment. Coal fly-ash based geopolymers are a low-cost, low greenhouse gas footprint alternative to metakaolin based materials. Both the grouting of sludge/powders/liquids and encapsulation of solids/compacted waste rely on the grout maintaining optimal flow (theological properties) during the mixing and pouring operations, and achieving a set leading to proper long term solidification (mechanical properties). The initial and final setting time for fly-ash geopolymer paste, based on the SRPS EN 196-3 standard, has been measured upon irradiation by gamma rays in a Co-60 reference field positioned with a kerma air rate of 3.42 mGys(-1). The binder paste was prepared using fly-ash from the TENT B power plant's electrostatic filters without further sieving, activated by water glass with module 1.5 and mixed with distilled water until a satisfactory flow was obtained, and poured into the sample and control molds. The initial and final setting times for the irradiated sample and non-irradiated control were determined by the Vicat apparatus. The irradiated sample demonstrated an 11 % shorter initial setting time, and 16 % shorter final setting time, compared to the control.",
publisher = "Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd",
journal = "Nuclear Technology & Radiation Protection",
title = "The effect of co-60 gamma irradiation on coal fly-ash geopolymer paste setting time",
pages = "153-150",
number = "2",
volume = "35",
doi = "10.2298/NTRP2002150R"
}

Rubinjoni, L., Stanković, S. J.,& Lončar, B.. (2020). The effect of co-60 gamma irradiation on coal fly-ash geopolymer paste setting time. in Nuclear Technology & Radiation Protection
Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd., 35(2), 150-153.
https://doi.org/10.2298/NTRP2002150R

Rubinjoni L, Stanković SJ, Lončar B. The effect of co-60 gamma irradiation on coal fly-ash geopolymer paste setting time. in Nuclear Technology & Radiation Protection. 2020;35(2):150-153.
doi:10.2298/NTRP2002150R .

Rubinjoni, Luka, Stanković, Srboljub J., Lončar, Boris, "The effect of co-60 gamma irradiation on coal fly-ash geopolymer paste setting time" in Nuclear Technology & Radiation Protection, 35, no. 2 (2020):150-153,
https://doi.org/10.2298/NTRP2002150R . .

TY  - JOUR
AU  - Awhida, Ahmed
AU  - Ujić, Predrag
AU  - Pantelić, Gordana K.
AU  - Kolarž, Predrag M.
AU  - Čeliković, Igor T.
AU  - Živanović, Miloš Z.
AU  - Janićijević, Aco
AU  - Lončar, Boris
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3953
AB  - It is indicated that the exposure to radon originating from the building materials is not negligible and the radon exhalation measurement should get more attention in the future. The experience with four different methods of the exhalation measurement, established in our laboratory for the purpose of the intercomparison is reported. Additionally, a comparison of advantages and disadvantages of used methods is discussed.
PB  - Oxford Univ Press, Oxford
T2  - Radiation Protection Dosimetry
T1  - Ad-hoc intercomparison of four different radon exhalation measurement methods
EP  - 142
IS  - 2
SP  - 138
VL  - 178
DO  - 10.1093/rpd/ncx096
ER  - 

@article{
author = "Awhida, Ahmed and Ujić, Predrag and Pantelić, Gordana K. and Kolarž, Predrag M. and Čeliković, Igor T. and Živanović, Miloš Z. and Janićijević, Aco and Lončar, Boris",
year = "2018",
abstract = "It is indicated that the exposure to radon originating from the building materials is not negligible and the radon exhalation measurement should get more attention in the future. The experience with four different methods of the exhalation measurement, established in our laboratory for the purpose of the intercomparison is reported. Additionally, a comparison of advantages and disadvantages of used methods is discussed.",
publisher = "Oxford Univ Press, Oxford",
journal = "Radiation Protection Dosimetry",
title = "Ad-hoc intercomparison of four different radon exhalation measurement methods",
pages = "142-138",
number = "2",
volume = "178",
doi = "10.1093/rpd/ncx096"
}

Awhida, A., Ujić, P., Pantelić, G. K., Kolarž, P. M., Čeliković, I. T., Živanović, M. Z., Janićijević, A.,& Lončar, B.. (2018). Ad-hoc intercomparison of four different radon exhalation measurement methods. in Radiation Protection Dosimetry
Oxford Univ Press, Oxford., 178(2), 138-142.
https://doi.org/10.1093/rpd/ncx096

Awhida A, Ujić P, Pantelić GK, Kolarž PM, Čeliković IT, Živanović MZ, Janićijević A, Lončar B. Ad-hoc intercomparison of four different radon exhalation measurement methods. in Radiation Protection Dosimetry. 2018;178(2):138-142.
doi:10.1093/rpd/ncx096 .

Awhida, Ahmed, Ujić, Predrag, Pantelić, Gordana K., Kolarž, Predrag M., Čeliković, Igor T., Živanović, Miloš Z., Janićijević, Aco, Lončar, Boris, "Ad-hoc intercomparison of four different radon exhalation measurement methods" in Radiation Protection Dosimetry, 178, no. 2 (2018):138-142,
https://doi.org/10.1093/rpd/ncx096 . .

TY  - JOUR
AU  - Stanković, Srboljub J.
AU  - Ilić, R. D.
AU  - Janković, Ksenija
AU  - Vasić-Milovanović, A.
AU  - Lončar, Boris
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5629
AB  - This work presents a characterization of radiation absorption properties of silicon carbide (SiC) as semiconductor for the realization of detectors for X-rays. SiC detectors can potentially reach superior performance with respect to all the other semiconductors presently employed in hazardous environments in nuclear and space science and technology. Physics and numerical modeling of photons transport through SiC detector is incorporated in non-destructive Monte Carlo method for determining the energy deposited and dose distribution. The Monte Carlo code has been adopted for numerical simulations for different detector conditions and configurations. The X-ray characterization of new SiC structures originates the improving of design of these detector systems.
PB  - Polish Acad Sciences Inst Physics, Warsaw
T2  - Acta Physica Polonica A
T1  - Characterization of New Structure for Silicon Carbide X-Ray Detector by Method Monte Carlo
EP  - 255
IS  - 2
SP  - 252
VL  - 120
DO  - 10.12693/APhysPolA.120.252
ER  - 

@article{
author = "Stanković, Srboljub J. and Ilić, R. D. and Janković, Ksenija and Vasić-Milovanović, A. and Lončar, Boris",
year = "2011",
abstract = "This work presents a characterization of radiation absorption properties of silicon carbide (SiC) as semiconductor for the realization of detectors for X-rays. SiC detectors can potentially reach superior performance with respect to all the other semiconductors presently employed in hazardous environments in nuclear and space science and technology. Physics and numerical modeling of photons transport through SiC detector is incorporated in non-destructive Monte Carlo method for determining the energy deposited and dose distribution. The Monte Carlo code has been adopted for numerical simulations for different detector conditions and configurations. The X-ray characterization of new SiC structures originates the improving of design of these detector systems.",
publisher = "Polish Acad Sciences Inst Physics, Warsaw",
journal = "Acta Physica Polonica A",
title = "Characterization of New Structure for Silicon Carbide X-Ray Detector by Method Monte Carlo",
pages = "255-252",
number = "2",
volume = "120",
doi = "10.12693/APhysPolA.120.252"
}

Stanković, S. J., Ilić, R. D., Janković, K., Vasić-Milovanović, A.,& Lončar, B.. (2011). Characterization of New Structure for Silicon Carbide X-Ray Detector by Method Monte Carlo. in Acta Physica Polonica A
Polish Acad Sciences Inst Physics, Warsaw., 120(2), 252-255.
https://doi.org/10.12693/APhysPolA.120.252

Stanković SJ, Ilić RD, Janković K, Vasić-Milovanović A, Lončar B. Characterization of New Structure for Silicon Carbide X-Ray Detector by Method Monte Carlo. in Acta Physica Polonica A. 2011;120(2):252-255.
doi:10.12693/APhysPolA.120.252 .

Stanković, Srboljub J., Ilić, R. D., Janković, Ksenija, Vasić-Milovanović, A., Lončar, Boris, "Characterization of New Structure for Silicon Carbide X-Ray Detector by Method Monte Carlo" in Acta Physica Polonica A, 120, no. 2 (2011):252-255,
https://doi.org/10.12693/APhysPolA.120.252 . .

TY  - JOUR
AU  - Smiljanić, Slavko N.
AU  - Smičiklas, Ivana D.
AU  - Perić-Grujić, Aleksandra
AU  - Šljivić-Ivanović, Marija Z.
AU  - Dukić, B.
AU  - Lončar, Boris
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1959
AB  - The waste red mud, remaining in remarkable quantities after the digestion of bauxite ores following the Bayer process, contains number of voluble minerals with excellent sorption properties towards aqueous heavy metals. Heating at 600 degrees C was found to be a favorable treatment for revalorization of rinsed red mud into an efficient Ni2+ sorbent (RBRM600). As potential practical application of RBRM600 for Ni2+ accumulation greatly depends on the solution composition and pH, the influence of these vital process variables was considered in this study. The initial pH rise from 2 to 3.5 caused the most evident increase in the amounts of Ni2+ removed: furthermore, the effect was more obvious for lower initial sorbate concentrations. Conversely, changes of the solution pH between 3.5 and 8 did not have a significant influence on the sorption. The increase of initial cation concentration caused the increase of the sorbed amount. following Langmuir isotherm model. The calculated maximum sorption capacity of 27.54 mg/g demonstrated capacity increase of approximately 20% in respect to inactivated rinsed red mud. Coexisting cations inhibited Ni2+ removal in the following order: Cu2+  gt  Pb2+  gt = Zn2+  gt  Cd2+  gt  gt  Ca2+, whereas the presence of Na+ and K+ did not affect the process. The investigated anions caused decrease of Ni2+ removal efficiency in the order: EDTA  gt  chromate  gt  acetate  gt  sulphate, however, fluoride slightly improved sorption. Low desorption of Ni2+ in various media showed that the heavy metal cations are tightly bound to RBRM600 surface, thus disposal or reuse of spent sorbent should be considered.
PB  - Elsevier Science Sa, Lausanne
T2  - Chemical Engineering Journal
T1  - Study of factors affecting Ni2+ immobilization efficiency by temperature activated red mud
EP  - 619
IS  - 2
SP  - 610
VL  - 168
DO  - 10.1016/j.cej.2011.01.034
ER  - 

@article{
author = "Smiljanić, Slavko N. and Smičiklas, Ivana D. and Perić-Grujić, Aleksandra and Šljivić-Ivanović, Marija Z. and Dukić, B. and Lončar, Boris",
year = "2011",
abstract = "The waste red mud, remaining in remarkable quantities after the digestion of bauxite ores following the Bayer process, contains number of voluble minerals with excellent sorption properties towards aqueous heavy metals. Heating at 600 degrees C was found to be a favorable treatment for revalorization of rinsed red mud into an efficient Ni2+ sorbent (RBRM600). As potential practical application of RBRM600 for Ni2+ accumulation greatly depends on the solution composition and pH, the influence of these vital process variables was considered in this study. The initial pH rise from 2 to 3.5 caused the most evident increase in the amounts of Ni2+ removed: furthermore, the effect was more obvious for lower initial sorbate concentrations. Conversely, changes of the solution pH between 3.5 and 8 did not have a significant influence on the sorption. The increase of initial cation concentration caused the increase of the sorbed amount. following Langmuir isotherm model. The calculated maximum sorption capacity of 27.54 mg/g demonstrated capacity increase of approximately 20% in respect to inactivated rinsed red mud. Coexisting cations inhibited Ni2+ removal in the following order: Cu2+  gt  Pb2+  gt = Zn2+  gt  Cd2+  gt  gt  Ca2+, whereas the presence of Na+ and K+ did not affect the process. The investigated anions caused decrease of Ni2+ removal efficiency in the order: EDTA  gt  chromate  gt  acetate  gt  sulphate, however, fluoride slightly improved sorption. Low desorption of Ni2+ in various media showed that the heavy metal cations are tightly bound to RBRM600 surface, thus disposal or reuse of spent sorbent should be considered.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Chemical Engineering Journal",
title = "Study of factors affecting Ni2+ immobilization efficiency by temperature activated red mud",
pages = "619-610",
number = "2",
volume = "168",
doi = "10.1016/j.cej.2011.01.034"
}

Smiljanić, S. N., Smičiklas, I. D., Perić-Grujić, A., Šljivić-Ivanović, M. Z., Dukić, B.,& Lončar, B.. (2011). Study of factors affecting Ni2+ immobilization efficiency by temperature activated red mud. in Chemical Engineering Journal
Elsevier Science Sa, Lausanne., 168(2), 610-619.
https://doi.org/10.1016/j.cej.2011.01.034

Smiljanić SN, Smičiklas ID, Perić-Grujić A, Šljivić-Ivanović MZ, Dukić B, Lončar B. Study of factors affecting Ni2+ immobilization efficiency by temperature activated red mud. in Chemical Engineering Journal. 2011;168(2):610-619.
doi:10.1016/j.cej.2011.01.034 .

Smiljanić, Slavko N., Smičiklas, Ivana D., Perić-Grujić, Aleksandra, Šljivić-Ivanović, Marija Z., Dukić, B., Lončar, Boris, "Study of factors affecting Ni2+ immobilization efficiency by temperature activated red mud" in Chemical Engineering Journal, 168, no. 2 (2011):610-619,
https://doi.org/10.1016/j.cej.2011.01.034 . .

TY  - JOUR
AU  - Lukić, Petar M.
AU  - Šašić, Rajko
AU  - Lončar, Boris
AU  - Zunjić, A. G.
PY  - 2011
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1945
AB  - This paper presents new results obtained by investigations of silicon carbide (SiC) based vertical Double Implanted Metal Oxide Semiconductor Field Effect Transistor (DIMOSFET). The results are described and presented by the analytical model of drift region voltage and its impact on SiC DIMOSFET current-voltage characteristics. The drift region is devided into sections. For each of them, voltage analytical model across the corresponding section is developed. Mobility dependence model on temperature and electric field is introduced. Finally, current-voltage characteristics are obtained, by using drain to surce voltage model which incorporate the mentioned partial voltages. Proposed model is based on the physics of the SiC DIMOSFET. Significant effects are taken into account, thus the model is accurate. At the same time exposed model is relatively simple. By using developed model simulations were performed. The obtained results are in very good agreement with already known and published ones..
PB  - Natl Inst Optoelectronics, Bucharest-Magurele
T2  - Optoelectronics and Advanced Materials-Rapid Communications
T1  - Analytical model of SiC DIMOSFET's drift region voltage impact on current-voltage characteristics
EP  - 554
IS  - 5-6
SP  - 551
VL  - 5
UR  - https://hdl.handle.net/21.15107/rcub_technorep_1945
ER  - 

@article{
author = "Lukić, Petar M. and Šašić, Rajko and Lončar, Boris and Zunjić, A. G.",
year = "2011",
abstract = "This paper presents new results obtained by investigations of silicon carbide (SiC) based vertical Double Implanted Metal Oxide Semiconductor Field Effect Transistor (DIMOSFET). The results are described and presented by the analytical model of drift region voltage and its impact on SiC DIMOSFET current-voltage characteristics. The drift region is devided into sections. For each of them, voltage analytical model across the corresponding section is developed. Mobility dependence model on temperature and electric field is introduced. Finally, current-voltage characteristics are obtained, by using drain to surce voltage model which incorporate the mentioned partial voltages. Proposed model is based on the physics of the SiC DIMOSFET. Significant effects are taken into account, thus the model is accurate. At the same time exposed model is relatively simple. By using developed model simulations were performed. The obtained results are in very good agreement with already known and published ones..",
publisher = "Natl Inst Optoelectronics, Bucharest-Magurele",
journal = "Optoelectronics and Advanced Materials-Rapid Communications",
title = "Analytical model of SiC DIMOSFET's drift region voltage impact on current-voltage characteristics",
pages = "554-551",
number = "5-6",
volume = "5",
url = "https://hdl.handle.net/21.15107/rcub_technorep_1945"
}

Lukić, P. M., Šašić, R., Lončar, B.,& Zunjić, A. G.. (2011). Analytical model of SiC DIMOSFET's drift region voltage impact on current-voltage characteristics. in Optoelectronics and Advanced Materials-Rapid Communications
Natl Inst Optoelectronics, Bucharest-Magurele., 5(5-6), 551-554.
https://hdl.handle.net/21.15107/rcub_technorep_1945

Lukić PM, Šašić R, Lončar B, Zunjić AG. Analytical model of SiC DIMOSFET's drift region voltage impact on current-voltage characteristics. in Optoelectronics and Advanced Materials-Rapid Communications. 2011;5(5-6):551-554.
https://hdl.handle.net/21.15107/rcub_technorep_1945 .

Lukić, Petar M., Šašić, Rajko, Lončar, Boris, Zunjić, A. G., "Analytical model of SiC DIMOSFET's drift region voltage impact on current-voltage characteristics" in Optoelectronics and Advanced Materials-Rapid Communications, 5, no. 5-6 (2011):551-554,
https://hdl.handle.net/21.15107/rcub_technorep_1945 .

TY  - JOUR
AU  - Smiljanić, Slavko N.
AU  - Smičiklas, Ivana D.
AU  - Perić-Grujić, Aleksandra
AU  - Lončar, Boris
AU  - Mitrić, Miodrag
PY  - 2010
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/1654
AB  - Red mud, an abundant industrial waste from alumina industry, represents a rich source of various metal oxides, mainly of Fe2O3 Al2O3 and SiO2. In this study, the rinsed Bosnian red mud (RBRM) was evaluated as an economical, composite sorbent for aqueous Ni2+ ions. The process was investigated as a function of pH, contact time and initial metal concentration. The investigated mineral mixture exhibited a high acid neutralising capacity, and its most important role in cation immobilization was observed in the initial pH range 2-8. The initial metal ion concentration strongly influenced the sorption kinetics and equilibrium times. Addition of 5 g/L of RBRM caused 100% removal from the solutions of 10(-4) to 5 x 10(-4) mol/L, whereas with the further increase of Ni2+ concentration to 8 x 10(-3) mol/L, the removal efficiency decreased to 26%. The maximum sorption capacity of 0.372 mmol/g, at initial pH 5, was determined using Langmuir theoretical model. The possibility of sorption efficiency improvement by annealing RBRM powder was investigated in the range 200-900 degrees C and the relationships between temperature, red mud physicochemical and sorption properties were established. The optimum heating temperature was found to be 600 degrees C, due to water exclusion from gibbsite and bayerite phases, leading to improved porosity and surface area, as well as increased pH value and sorption efficiency. The stability of the sorbed cation was assessed by leaching experiments in distilled water and acidic TCLP2 solution.
PB  - Elsevier Science Sa, Lausanne
T2  - Chemical Engineering Journal
T1  - Rinsed and thermally treated red mud sorbents for aqueous Ni2+ ions
EP  - 83
IS  - 1
SP  - 75
VL  - 162
DO  - 10.1016/j.cej.2010.04.062
ER  - 

@article{
author = "Smiljanić, Slavko N. and Smičiklas, Ivana D. and Perić-Grujić, Aleksandra and Lončar, Boris and Mitrić, Miodrag",
year = "2010",
abstract = "Red mud, an abundant industrial waste from alumina industry, represents a rich source of various metal oxides, mainly of Fe2O3 Al2O3 and SiO2. In this study, the rinsed Bosnian red mud (RBRM) was evaluated as an economical, composite sorbent for aqueous Ni2+ ions. The process was investigated as a function of pH, contact time and initial metal concentration. The investigated mineral mixture exhibited a high acid neutralising capacity, and its most important role in cation immobilization was observed in the initial pH range 2-8. The initial metal ion concentration strongly influenced the sorption kinetics and equilibrium times. Addition of 5 g/L of RBRM caused 100% removal from the solutions of 10(-4) to 5 x 10(-4) mol/L, whereas with the further increase of Ni2+ concentration to 8 x 10(-3) mol/L, the removal efficiency decreased to 26%. The maximum sorption capacity of 0.372 mmol/g, at initial pH 5, was determined using Langmuir theoretical model. The possibility of sorption efficiency improvement by annealing RBRM powder was investigated in the range 200-900 degrees C and the relationships between temperature, red mud physicochemical and sorption properties were established. The optimum heating temperature was found to be 600 degrees C, due to water exclusion from gibbsite and bayerite phases, leading to improved porosity and surface area, as well as increased pH value and sorption efficiency. The stability of the sorbed cation was assessed by leaching experiments in distilled water and acidic TCLP2 solution.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Chemical Engineering Journal",
title = "Rinsed and thermally treated red mud sorbents for aqueous Ni2+ ions",
pages = "83-75",
number = "1",
volume = "162",
doi = "10.1016/j.cej.2010.04.062"
}

Smiljanić, S. N., Smičiklas, I. D., Perić-Grujić, A., Lončar, B.,& Mitrić, M.. (2010). Rinsed and thermally treated red mud sorbents for aqueous Ni2+ ions. in Chemical Engineering Journal
Elsevier Science Sa, Lausanne., 162(1), 75-83.
https://doi.org/10.1016/j.cej.2010.04.062

Smiljanić SN, Smičiklas ID, Perić-Grujić A, Lončar B, Mitrić M. Rinsed and thermally treated red mud sorbents for aqueous Ni2+ ions. in Chemical Engineering Journal. 2010;162(1):75-83.
doi:10.1016/j.cej.2010.04.062 .

Smiljanić, Slavko N., Smičiklas, Ivana D., Perić-Grujić, Aleksandra, Lončar, Boris, Mitrić, Miodrag, "Rinsed and thermally treated red mud sorbents for aqueous Ni2+ ions" in Chemical Engineering Journal, 162, no. 1 (2010):75-83,
https://doi.org/10.1016/j.cej.2010.04.062 . .

TY  - JOUR
AU  - Osmokrović, P.
AU  - Vujisic, M.
AU  - Stanković, K.
AU  - Vasić, A.
AU  - Lončar, Boris
PY  - 2007
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5504
AB  - This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.
PB  - Institute of Physics Publishing
T2  - Plasma Sources Science and Technology
T1  - Mechanism of electrical breakdown of gases for pressures from 10 -9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm
EP  - 655
IS  - 3
SP  - 643
VL  - 16
DO  - 10.1088/0963-0252/16/3/025
ER  - 

@article{
author = "Osmokrović, P. and Vujisic, M. and Stanković, K. and Vasić, A. and Lončar, Boris",
year = "2007",
abstract = "This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.",
publisher = "Institute of Physics Publishing",
journal = "Plasma Sources Science and Technology",
title = "Mechanism of electrical breakdown of gases for pressures from 10 -9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm",
pages = "655-643",
number = "3",
volume = "16",
doi = "10.1088/0963-0252/16/3/025"
}

Osmokrović, P., Vujisic, M., Stanković, K., Vasić, A.,& Lončar, B.. (2007). Mechanism of electrical breakdown of gases for pressures from 10 -9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm. in Plasma Sources Science and Technology
Institute of Physics Publishing., 16(3), 643-655.
https://doi.org/10.1088/0963-0252/16/3/025

Osmokrović P, Vujisic M, Stanković K, Vasić A, Lončar B. Mechanism of electrical breakdown of gases for pressures from 10 -9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm. in Plasma Sources Science and Technology. 2007;16(3):643-655.
doi:10.1088/0963-0252/16/3/025 .

Osmokrović, P., Vujisic, M., Stanković, K., Vasić, A., Lončar, Boris, "Mechanism of electrical breakdown of gases for pressures from 10 -9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm" in Plasma Sources Science and Technology, 16, no. 3 (2007):643-655,
https://doi.org/10.1088/0963-0252/16/3/025 . .

TY  - JOUR
AU  - Vujisic, M.
AU  - Osmokrović, P.
AU  - Lončar, Boris
PY  - 2007
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5507
AB  - This paper examines the reliability of commercial off the shelf (COTS) erasable programmable read only memory (EPROM) and electrically erasable programmable read only memory (EEPROM) components exposed to gamma radiation. Results obtained for 64 KB EPROM (NM27C512) and 16 KB EEPROM (M24128) components provide evidence that EPROMs have greater radiation hardness than EEPROMs. Moreover, the changes in EPROMs are reversible, and after erasure and reprogramming all EPROM components restore their functionality. On the other hand, changes in EEPROMs are irreversible. The obtained results are analysed and interpreted on the basis of gamma ray interaction with the oxide layer.
PB  - Institute of Physics Publishing
T2  - Journal of Physics D: Applied Physics
T1  - Gamma irradiation effects in programmable read only memories
EP  - 5789
IS  - 18
SP  - 5785
VL  - 40
DO  - 10.1088/0022-3727/40/18/041
ER  - 

@article{
author = "Vujisic, M. and Osmokrović, P. and Lončar, Boris",
year = "2007",
abstract = "This paper examines the reliability of commercial off the shelf (COTS) erasable programmable read only memory (EPROM) and electrically erasable programmable read only memory (EEPROM) components exposed to gamma radiation. Results obtained for 64 KB EPROM (NM27C512) and 16 KB EEPROM (M24128) components provide evidence that EPROMs have greater radiation hardness than EEPROMs. Moreover, the changes in EPROMs are reversible, and after erasure and reprogramming all EPROM components restore their functionality. On the other hand, changes in EEPROMs are irreversible. The obtained results are analysed and interpreted on the basis of gamma ray interaction with the oxide layer.",
publisher = "Institute of Physics Publishing",
journal = "Journal of Physics D: Applied Physics",
title = "Gamma irradiation effects in programmable read only memories",
pages = "5789-5785",
number = "18",
volume = "40",
doi = "10.1088/0022-3727/40/18/041"
}

Vujisic, M., Osmokrović, P.,& Lončar, B.. (2007). Gamma irradiation effects in programmable read only memories. in Journal of Physics D: Applied Physics
Institute of Physics Publishing., 40(18), 5785-5789.
https://doi.org/10.1088/0022-3727/40/18/041

Vujisic M, Osmokrović P, Lončar B. Gamma irradiation effects in programmable read only memories. in Journal of Physics D: Applied Physics. 2007;40(18):5785-5789.
doi:10.1088/0022-3727/40/18/041 .

Vujisic, M., Osmokrović, P., Lončar, Boris, "Gamma irradiation effects in programmable read only memories" in Journal of Physics D: Applied Physics, 40, no. 18 (2007):5785-5789,
https://doi.org/10.1088/0022-3727/40/18/041 . .

TY  - JOUR
AU  - Lončar, Boris
AU  - Osmokrović, P.
AU  - Stanković, Srboljub J.
AU  - Šašić, Rajko
PY  - 2006
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/881
AB  - The aim of this paper is to find the possibility for improvement of gas-filled surge arresters (GFSA) characteristics in y and X radiation field by appropriate choice of electrode materials. For that purpose electrodes made of different materials were incorporated in the originally developed GFSA model. The obtained results show that both in y and X radiation fields, copper electrodes are an optimal solution, since they have the highest resistance to radiation effects. It is also shown GFSA are highly resistant to y radiation, but that X radiation leads to significant degradation of their characteristics.
PB  - Natl Inst Optoelectronics, Bucharest-Magurele
T2  - Journal of Optoelectronics and Advanced Materials
T1  - Influence of electrode material on gas-filled surge arresters characteristics in gamma and X radiation field
EP  - 866
IS  - 2
SP  - 863
VL  - 8
UR  - https://hdl.handle.net/21.15107/rcub_vinar_3010
ER  - 

@article{
author = "Lončar, Boris and Osmokrović, P. and Stanković, Srboljub J. and Šašić, Rajko",
year = "2006",
abstract = "The aim of this paper is to find the possibility for improvement of gas-filled surge arresters (GFSA) characteristics in y and X radiation field by appropriate choice of electrode materials. For that purpose electrodes made of different materials were incorporated in the originally developed GFSA model. The obtained results show that both in y and X radiation fields, copper electrodes are an optimal solution, since they have the highest resistance to radiation effects. It is also shown GFSA are highly resistant to y radiation, but that X radiation leads to significant degradation of their characteristics.",
publisher = "Natl Inst Optoelectronics, Bucharest-Magurele",
journal = "Journal of Optoelectronics and Advanced Materials",
title = "Influence of electrode material on gas-filled surge arresters characteristics in gamma and X radiation field",
pages = "866-863",
number = "2",
volume = "8",
url = "https://hdl.handle.net/21.15107/rcub_vinar_3010"
}

Lončar, B., Osmokrović, P., Stanković, S. J.,& Šašić, R.. (2006). Influence of electrode material on gas-filled surge arresters characteristics in gamma and X radiation field. in Journal of Optoelectronics and Advanced Materials
Natl Inst Optoelectronics, Bucharest-Magurele., 8(2), 863-866.
https://hdl.handle.net/21.15107/rcub_vinar_3010

Lončar B, Osmokrović P, Stanković SJ, Šašić R. Influence of electrode material on gas-filled surge arresters characteristics in gamma and X radiation field. in Journal of Optoelectronics and Advanced Materials. 2006;8(2):863-866.
https://hdl.handle.net/21.15107/rcub_vinar_3010 .

Lončar, Boris, Osmokrović, P., Stanković, Srboljub J., Šašić, Rajko, "Influence of electrode material on gas-filled surge arresters characteristics in gamma and X radiation field" in Journal of Optoelectronics and Advanced Materials, 8, no. 2 (2006):863-866,
https://hdl.handle.net/21.15107/rcub_vinar_3010 .

TY  - JOUR
AU  - Osmokrović, Predrag
AU  - Zivić, Tamara
AU  - Lončar, Boris
AU  - Vasić, Aleksandra
PY  - 2006
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5463
AB  - This paper investigates the validity of the similarity law in cases of dc and pulse breakdown of gases. Geometrically similar systems insulated with SF6 gas were used during experiments. It is shown that the similarity law is valid for dc breakdown voltage if the electron mean free path is included in geometrical parameters of the system, but not for pulse breakdown voltages. The explanation for this is the mechanism of the pulse discharge. The similarity law was expanded to take into account mechanisms of pulse breakdown initiation. Thus, the general similarity law is obtained, the validity of which in case of a pulse breakdown is established experimentally.
PB  - IOP Publishing Ltd, Bristol
T2  - Plasma Sources Science & Technology
T1  - The validity of the general similarity law for electrical breakdown of gases
EP  - 713
IS  - 4
SP  - 703
VL  - 15
DO  - 10.1088/0963-0252/15/4/015
ER  - 

@article{
author = "Osmokrović, Predrag and Zivić, Tamara and Lončar, Boris and Vasić, Aleksandra",
year = "2006",
abstract = "This paper investigates the validity of the similarity law in cases of dc and pulse breakdown of gases. Geometrically similar systems insulated with SF6 gas were used during experiments. It is shown that the similarity law is valid for dc breakdown voltage if the electron mean free path is included in geometrical parameters of the system, but not for pulse breakdown voltages. The explanation for this is the mechanism of the pulse discharge. The similarity law was expanded to take into account mechanisms of pulse breakdown initiation. Thus, the general similarity law is obtained, the validity of which in case of a pulse breakdown is established experimentally.",
publisher = "IOP Publishing Ltd, Bristol",
journal = "Plasma Sources Science & Technology",
title = "The validity of the general similarity law for electrical breakdown of gases",
pages = "713-703",
number = "4",
volume = "15",
doi = "10.1088/0963-0252/15/4/015"
}

Osmokrović, P., Zivić, T., Lončar, B.,& Vasić, A.. (2006). The validity of the general similarity law for electrical breakdown of gases. in Plasma Sources Science & Technology
IOP Publishing Ltd, Bristol., 15(4), 703-713.
https://doi.org/10.1088/0963-0252/15/4/015

Osmokrović P, Zivić T, Lončar B, Vasić A. The validity of the general similarity law for electrical breakdown of gases. in Plasma Sources Science & Technology. 2006;15(4):703-713.
doi:10.1088/0963-0252/15/4/015 .

Osmokrović, Predrag, Zivić, Tamara, Lončar, Boris, Vasić, Aleksandra, "The validity of the general similarity law for electrical breakdown of gases" in Plasma Sources Science & Technology, 15, no. 4 (2006):703-713,
https://doi.org/10.1088/0963-0252/15/4/015 . .

TY  - JOUR
AU  - Lončar, Boris
AU  - Osmokrović, P.
AU  - Vasić, A.
AU  - Šašić, Rajko
PY  - 2006
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/992
AB  - The aim of this paper is to present the electrode effects as approach for the improvement of gas filled surge arresters (GFSA) protective characteristics in the most optimal way. We examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.
PB  - IEEE, Electron Devices Soc & Reliability Group, New York
T2  - 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings
T1  - Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics
EP  - +
SP  - 631
UR  - https://hdl.handle.net/21.15107/rcub_technorep_992
ER  - 

@article{
author = "Lončar, Boris and Osmokrović, P. and Vasić, A. and Šašić, Rajko",
year = "2006",
abstract = "The aim of this paper is to present the electrode effects as approach for the improvement of gas filled surge arresters (GFSA) protective characteristics in the most optimal way. We examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.",
publisher = "IEEE, Electron Devices Soc & Reliability Group, New York",
journal = "2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings",
title = "Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics",
pages = "+-631",
url = "https://hdl.handle.net/21.15107/rcub_technorep_992"
}

Lončar, B., Osmokrović, P., Vasić, A.,& Šašić, R.. (2006). Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics. in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings
IEEE, Electron Devices Soc & Reliability Group, New York., 631-+.
https://hdl.handle.net/21.15107/rcub_technorep_992

Lončar B, Osmokrović P, Vasić A, Šašić R. Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics. in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings. 2006;:631-+.
https://hdl.handle.net/21.15107/rcub_technorep_992 .

Lončar, Boris, Osmokrović, P., Vasić, A., Šašić, Rajko, "Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics" in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings (2006):631-+,
https://hdl.handle.net/21.15107/rcub_technorep_992 .

TY  - JOUR
AU  - Lončar, Boris
AU  - Osmokrović, P.
AU  - Vasić, A.
AU  - Šašić, Rajko
PY  - 2006
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/872
AB  - The aim of this paper is to present the electrode effects as approach for the improvement of gas filled surge arresters (GFSA) protective characteristics in the most optimal way. We examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.
PB  - 2006 25th International Conference on Microelectronics, MIEL 2006
T2  - 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings
T1  - Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics
EP  - 594
SP  - 591
DO  - 10.1109/ICMEL.2006.1651036
ER  - 

@article{
author = "Lončar, Boris and Osmokrović, P. and Vasić, A. and Šašić, Rajko",
year = "2006",
abstract = "The aim of this paper is to present the electrode effects as approach for the improvement of gas filled surge arresters (GFSA) protective characteristics in the most optimal way. We examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.",
publisher = "2006 25th International Conference on Microelectronics, MIEL 2006",
journal = "2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings",
title = "Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics",
pages = "594-591",
doi = "10.1109/ICMEL.2006.1651036"
}

Lončar, B., Osmokrović, P., Vasić, A.,& Šašić, R.. (2006). Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics. in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings
2006 25th International Conference on Microelectronics, MIEL 2006., 591-594.
https://doi.org/10.1109/ICMEL.2006.1651036

Lončar B, Osmokrović P, Vasić A, Šašić R. Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics. in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings. 2006;:591-594.
doi:10.1109/ICMEL.2006.1651036 .

Lončar, Boris, Osmokrović, P., Vasić, A., Šašić, Rajko, "Influence of electrode materials and the manner of electrode surface processing on gas-filled surge arresters relevant characteristics" in 2006 25th International Conference on Microelectronics, MIEL 2006 - Proceedings (2006):591-594,
https://doi.org/10.1109/ICMEL.2006.1651036 . .

TY  - JOUR
AU  - Osmokrović, P.
AU  - Lončar, Boris
AU  - Šašić, Rajko
PY  - 2005
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/838
AB  - The aim of this paper is to present the influence of electrode system parameters on electrical breakdown of gas (electrode effect) with the purpose to improve the gas-filled surge arresters (GFSAs) protective characteristics with the most optimal way. The influence of the electrode parameters on the pulse shape characteristics is examined. As variable parameters, the electrode material and the manner of electrode surface processing are used. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.
PB  - IEEE-Inst Electrical Electronics Engineers Inc, Piscataway
T2  - IEEE Transactions on Plasma Science
T1  - Influence of the electrode parameters on pulse shape characteristic of gas-filled surge arresters at small pressure and inter-electrode gap values
EP  - 1735
IS  - 5
SP  - 1729
VL  - 33
DO  - 10.1109/TPS.2005.856415
ER  - 

@article{
author = "Osmokrović, P. and Lončar, Boris and Šašić, Rajko",
year = "2005",
abstract = "The aim of this paper is to present the influence of electrode system parameters on electrical breakdown of gas (electrode effect) with the purpose to improve the gas-filled surge arresters (GFSAs) protective characteristics with the most optimal way. The influence of the electrode parameters on the pulse shape characteristics is examined. As variable parameters, the electrode material and the manner of electrode surface processing are used. The originally developed GFSA model with a composite electrode system enables a high degree of over-voltage protection without environmental contamination.",
publisher = "IEEE-Inst Electrical Electronics Engineers Inc, Piscataway",
journal = "IEEE Transactions on Plasma Science",
title = "Influence of the electrode parameters on pulse shape characteristic of gas-filled surge arresters at small pressure and inter-electrode gap values",
pages = "1735-1729",
number = "5",
volume = "33",
doi = "10.1109/TPS.2005.856415"
}

Osmokrović, P., Lončar, B.,& Šašić, R.. (2005). Influence of the electrode parameters on pulse shape characteristic of gas-filled surge arresters at small pressure and inter-electrode gap values. in IEEE Transactions on Plasma Science
IEEE-Inst Electrical Electronics Engineers Inc, Piscataway., 33(5), 1729-1735.
https://doi.org/10.1109/TPS.2005.856415

Osmokrović P, Lončar B, Šašić R. Influence of the electrode parameters on pulse shape characteristic of gas-filled surge arresters at small pressure and inter-electrode gap values. in IEEE Transactions on Plasma Science. 2005;33(5):1729-1735.
doi:10.1109/TPS.2005.856415 .

Osmokrović, P., Lončar, Boris, Šašić, Rajko, "Influence of the electrode parameters on pulse shape characteristic of gas-filled surge arresters at small pressure and inter-electrode gap values" in IEEE Transactions on Plasma Science, 33, no. 5 (2005):1729-1735,
https://doi.org/10.1109/TPS.2005.856415 . .

TY  - JOUR
AU  - Osmokrović, P.
AU  - Lončar, Boris
AU  - Šašić, Rajko
PY  - 2004
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/600
AB  - Gas filled surge arresters (GFSA) has working point close to minimum on Paschen curve. Below that point breakdown follows Townsend's mechanism, i.e. the secondary processes on the electrodes dominate the secondary processes in the gas. The most important parameter of GFSA is its pulse shape characteristic. The main problem in GFSA application is its delayed response. The built-in radioactive sources cause the significant improvement of GFSA characteristic. On the other hand, the use of GFSA with radioactive filling would be some-what danger to the environment. Specific problems arise from inade-quate procedure regulating for storage and destruction for GFSA with radioactive filling. The narrower the pulse characteristic is, the smaller response time is, i.e. the better protective characteristic of GFSA is. The aim of this paper is to present the electrode effects as approach for the improvement of GFSA protective characteristics in the most optimal way. In that purpose, we examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The electrodes were made either of copper, of aluminum or of electrons. The materials with higher values of output work corresponds larger pulse shape characteristics. In the case of investigation the influence of the manner of processing electrode surface on pulse shape characteristics, the electrodes were made of brass with polished, sand-processed or engraved. By applying the "area law" it is possible to determine the pulse shape characteristic based on single series of measurements (using single shape of the pulse voltage). An original analytical algorithm has been developed to determine and compare characteristics of GFSA for a pulse shape characteristic.
PB  - IEEE Conference Record - Abstracts: The 31st IEEE International Conference on Plasma Science, ICOPS2004
T2  - IEEE International Conference on Plasma Science
T1  - Influence of the electrode parameters on the pulse shape characteristic at small pressure and inter-electrode gap values
SP  - 447
UR  - https://hdl.handle.net/21.15107/rcub_technorep_600
ER  - 

@article{
author = "Osmokrović, P. and Lončar, Boris and Šašić, Rajko",
year = "2004",
abstract = "Gas filled surge arresters (GFSA) has working point close to minimum on Paschen curve. Below that point breakdown follows Townsend's mechanism, i.e. the secondary processes on the electrodes dominate the secondary processes in the gas. The most important parameter of GFSA is its pulse shape characteristic. The main problem in GFSA application is its delayed response. The built-in radioactive sources cause the significant improvement of GFSA characteristic. On the other hand, the use of GFSA with radioactive filling would be some-what danger to the environment. Specific problems arise from inade-quate procedure regulating for storage and destruction for GFSA with radioactive filling. The narrower the pulse characteristic is, the smaller response time is, i.e. the better protective characteristic of GFSA is. The aim of this paper is to present the electrode effects as approach for the improvement of GFSA protective characteristics in the most optimal way. In that purpose, we examined the influence of the electrode parameters on the pulse shape characteristics. As variable parameters, we used the electrode material and the manner of electrode surface processing. The electrodes were made either of copper, of aluminum or of electrons. The materials with higher values of output work corresponds larger pulse shape characteristics. In the case of investigation the influence of the manner of processing electrode surface on pulse shape characteristics, the electrodes were made of brass with polished, sand-processed or engraved. By applying the "area law" it is possible to determine the pulse shape characteristic based on single series of measurements (using single shape of the pulse voltage). An original analytical algorithm has been developed to determine and compare characteristics of GFSA for a pulse shape characteristic.",
publisher = "IEEE Conference Record - Abstracts: The 31st IEEE International Conference on Plasma Science, ICOPS2004",
journal = "IEEE International Conference on Plasma Science",
title = "Influence of the electrode parameters on the pulse shape characteristic at small pressure and inter-electrode gap values",
pages = "447",
url = "https://hdl.handle.net/21.15107/rcub_technorep_600"
}

Osmokrović, P., Lončar, B.,& Šašić, R.. (2004). Influence of the electrode parameters on the pulse shape characteristic at small pressure and inter-electrode gap values. in IEEE International Conference on Plasma Science
IEEE Conference Record - Abstracts: The 31st IEEE International Conference on Plasma Science, ICOPS2004., 447.
https://hdl.handle.net/21.15107/rcub_technorep_600

Osmokrović P, Lončar B, Šašić R. Influence of the electrode parameters on the pulse shape characteristic at small pressure and inter-electrode gap values. in IEEE International Conference on Plasma Science. 2004;:447.
https://hdl.handle.net/21.15107/rcub_technorep_600 .

Osmokrović, P., Lončar, Boris, Šašić, Rajko, "Influence of the electrode parameters on the pulse shape characteristic at small pressure and inter-electrode gap values" in IEEE International Conference on Plasma Science (2004):447,
https://hdl.handle.net/21.15107/rcub_technorep_600 .