Stevanović, Marija

Link to this page

Authority KeyName Variants
0e47ec75-b173-4c19-8490-aef80fd4c90c
  • Stevanović, Marija (1)
  • Stevanović, Marija S. (1)
Projects

Author's Bibliography

Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential

Jovanović, Aleksandar; Stevanović, Marija; Barudžija, Tanja; Cvijetić, Ilija; Lazarević, Slavica; Tomašević, Anđelka; Marinković, Aleksandar

(Institution of Chemical Engineers, 2023)

TY  - JOUR
AU  - Jovanović, Aleksandar
AU  - Stevanović, Marija
AU  - Barudžija, Tanja
AU  - Cvijetić, Ilija
AU  - Lazarević, Slavica
AU  - Tomašević, Anđelka
AU  - Marinković, Aleksandar
PY  - 2023
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6611
AB  - This study focuses on establishing an efficient two-step technology, which includes: (1) consecutive adsorption-desorption, using cellulose-based membranes, bCells, and (2) photocatalytic degradation of the fungicide thiophanate-methyl (TPM), using synthesized Ag-P25 and Ce-P25 catalysts. The catalysts, obtained by controlled deposition of Ag2O/Ag and CeO2 onto P25 TiO2 carrier (Degussa), were characterized using ATR-FTIR, XRPD, BET, FESEM, HRTEM, HAADF-EDS and UV–DRS techniques. In order to establish a feasible purification technology, preconcentration of TPM was performed by adsorption, achieving 75.5 and 92.9 mg/g of TPM removal using bCell-EpL and bCell–EpL–TA membranes, respectively, followed by efficient desorption (> 95%) that provided acceptable TPM concentration for photodegradation experiments. Under optimal conditions (0.07 g/L of both catalysts), complete degradation of TPM (5 mg/L) occurred within 2 h, compared to 4 h for the base TiO2 P25. Measurements of quantum yield and the results of HPLC-MS analysis, alongside DFT calculation, assisted in understanding the TPM degradation pathways. New degradation products were detected and proposed from HPLC–MS analysis. Embryotoxic assays, performed on zebrafish (Danio rerio), applied to estimate the toxicity evolution of time-dependent generated TPM degradation products, showed low embryotoxic potential. Chemical oxygen demand (26 mg O2/L) confirmed low ecotoxicological pressure of effluent water.
PB  - Institution of Chemical Engineers
T2  - Process Safety and Environmental Protection
T1  - Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential
EP  - 443
SP  - 423
VL  - 178
DO  - 10.1016/j.psep.2023.08.054
ER  - 
@article{
author = "Jovanović, Aleksandar and Stevanović, Marija and Barudžija, Tanja and Cvijetić, Ilija and Lazarević, Slavica and Tomašević, Anđelka and Marinković, Aleksandar",
year = "2023",
abstract = "This study focuses on establishing an efficient two-step technology, which includes: (1) consecutive adsorption-desorption, using cellulose-based membranes, bCells, and (2) photocatalytic degradation of the fungicide thiophanate-methyl (TPM), using synthesized Ag-P25 and Ce-P25 catalysts. The catalysts, obtained by controlled deposition of Ag2O/Ag and CeO2 onto P25 TiO2 carrier (Degussa), were characterized using ATR-FTIR, XRPD, BET, FESEM, HRTEM, HAADF-EDS and UV–DRS techniques. In order to establish a feasible purification technology, preconcentration of TPM was performed by adsorption, achieving 75.5 and 92.9 mg/g of TPM removal using bCell-EpL and bCell–EpL–TA membranes, respectively, followed by efficient desorption (> 95%) that provided acceptable TPM concentration for photodegradation experiments. Under optimal conditions (0.07 g/L of both catalysts), complete degradation of TPM (5 mg/L) occurred within 2 h, compared to 4 h for the base TiO2 P25. Measurements of quantum yield and the results of HPLC-MS analysis, alongside DFT calculation, assisted in understanding the TPM degradation pathways. New degradation products were detected and proposed from HPLC–MS analysis. Embryotoxic assays, performed on zebrafish (Danio rerio), applied to estimate the toxicity evolution of time-dependent generated TPM degradation products, showed low embryotoxic potential. Chemical oxygen demand (26 mg O2/L) confirmed low ecotoxicological pressure of effluent water.",
publisher = "Institution of Chemical Engineers",
journal = "Process Safety and Environmental Protection",
title = "Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential",
pages = "443-423",
volume = "178",
doi = "10.1016/j.psep.2023.08.054"
}
Jovanović, A., Stevanović, M., Barudžija, T., Cvijetić, I., Lazarević, S., Tomašević, A.,& Marinković, A.. (2023). Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential. in Process Safety and Environmental Protection
Institution of Chemical Engineers., 178, 423-443.
https://doi.org/10.1016/j.psep.2023.08.054
Jovanović A, Stevanović M, Barudžija T, Cvijetić I, Lazarević S, Tomašević A, Marinković A. Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential. in Process Safety and Environmental Protection. 2023;178:423-443.
doi:10.1016/j.psep.2023.08.054 .
Jovanović, Aleksandar, Stevanović, Marija, Barudžija, Tanja, Cvijetić, Ilija, Lazarević, Slavica, Tomašević, Anđelka, Marinković, Aleksandar, "Advanced technology for photocatalytic degradation of thiophanate-methyl: Degradation pathways, DFT calculations and embryotoxic potential" in Process Safety and Environmental Protection, 178 (2023):423-443,
https://doi.org/10.1016/j.psep.2023.08.054 . .

Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora

Stefanović, Milica P.; Vujančević, Jelena D.; Petrović, Rada P.; Stevanović, Marija S.; Janaćković, Đorđe T.

(Savez inženjera i tehničara Srbije, 2022)

TY  - JOUR
AU  - Stefanović, Milica P.
AU  - Vujančević, Jelena D.
AU  - Petrović, Rada P.
AU  - Stevanović, Marija S.
AU  - Janaćković, Đorđe T.
PY  - 2022
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5274
AB  - Organsko-neorganski perovskiti su privukli veliku pažnju istraživača zbog visoke apsorpcije u vidljivom
delu spektra i jeftine proizvodnje. Apsorbovanjem svetlosti dolazi do stvaranja para elektron-šupljina.
U cilju razdvajanja nosilaca naelektrisanja, perovskit se kombinuje sa TiO2 što ima za posledicu
spontani prelazak elektrona sa perovskita na TiO2. Ovo istraživanje je imalo za cilj povećanje dodirne
površine između nanocevi TiO2 i perovskita punjenjem nanocevi perovskitnim materijalom. Rastvor
metilamonijum olovo(II)-bromidnog perovskita (CH3NH3PbBr3) u dimetilformamidu (DMF) je
deponovan na anodizacijom sintetisane TiO2 nanocevi pomoću sistema visokog vakuuma i inertnog
gasa. Postupak je uključivao degazaciju uzorka u visokom vakuumu u trajanju od 3 h na 200 °C, hlađenje
uzorka, a zatim nanošenje rastvora CH3NH3PbBr3 u DMF-u, uz naknadni tretman inertnim gasom (N2)
u cilju ostvarenja natpritiska, što je omogućilo punjenje nanocevi perovskitnim materijalom. Difuznorefleksiona spektroskopija pokazala je da taloženje CH3NH3PbBr3 poboljšava apsorpciona svojstva
TiO2 nanocevi. I-V karakteristike uzorka pokazale su fotodiodno ponašanje i histerezisnu krivu, koja je
karakteristična za perovskitni materijal. Vrednost struje uzorka snimljenim pod vidljivom svetlošću
iznosila je 46 μA bez primene prednapona, dok je nakon primene prednapona iznosila 76 μA. Rezultati
rada ukazuju da je napravljena perovskitna fotodioda sa povećanim kontaktom između TiO2 i perovskita,
koja predstavlja osnovu za buduću konstrukciju solarnih ćelija.
AB  - Organic-inorganic perovskites have attracted much attention from researchers due to their high absorption in the visible part of the spectrum and low-cost fabrication. After absorption of the light, electron-hole pairs are formed. To separate electron-hole pairs and reduce recombination, perovskite is combined with TiO2 which has as a consequence, a spontaneous transition of electrons from perovskite to TiO2. This research aims to increase the contact surface of perovskite and TiO2 nanotubes by filling the nanotubes with perovskite material. The solution of methylammonium lead bromide perovskite (CH3NH3PbBr3) in dimethylformamide (DMF) was deposited on anodically synthesized TiO2 nanotubes by the high vacuum system and inert gas. The procedure involved degassation of the sample under high vacuum for 3 h at 200 °C, cooling of the sample, and putting the solution of CH3NH3PbBr3 in DMF, after which it was treated with inert gas (N2), as an overpressure which enabled the filling of the nanotubes with perovskite material. The diffuse reflectance spectroscopy measurement of the sample proved that deposition of CH3NH3PbBr3 improves the absorption properties of TiO2 nanotubes. The I-V characteristics of the sample showed photodiode behavior and characteristic hysteresis curve for perovskite material. The value of current under visible light for the sample without preconditioning was 46 mA, while after preconditioning value of current was 76 mA. The results indicate that a perovskite photodiode with increased contact between TiO2 and perovskite was made, which is the basis for future solar cell construction.
PB  - Savez inženjera i tehničara Srbije
T2  - Tehnika
T1  - Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora
T1  - Improvement of absorption properties of TiO2 nanotubes by using CH3NH3PbBr3 perovskite as photosensitizer
EP  - 21
IS  - 1
SP  - 15
VL  - 31
DO  - 10.5937/tehnika2201015S
ER  - 
@article{
author = "Stefanović, Milica P. and Vujančević, Jelena D. and Petrović, Rada P. and Stevanović, Marija S. and Janaćković, Đorđe T.",
year = "2022",
abstract = "Organsko-neorganski perovskiti su privukli veliku pažnju istraživača zbog visoke apsorpcije u vidljivom
delu spektra i jeftine proizvodnje. Apsorbovanjem svetlosti dolazi do stvaranja para elektron-šupljina.
U cilju razdvajanja nosilaca naelektrisanja, perovskit se kombinuje sa TiO2 što ima za posledicu
spontani prelazak elektrona sa perovskita na TiO2. Ovo istraživanje je imalo za cilj povećanje dodirne
površine između nanocevi TiO2 i perovskita punjenjem nanocevi perovskitnim materijalom. Rastvor
metilamonijum olovo(II)-bromidnog perovskita (CH3NH3PbBr3) u dimetilformamidu (DMF) je
deponovan na anodizacijom sintetisane TiO2 nanocevi pomoću sistema visokog vakuuma i inertnog
gasa. Postupak je uključivao degazaciju uzorka u visokom vakuumu u trajanju od 3 h na 200 °C, hlađenje
uzorka, a zatim nanošenje rastvora CH3NH3PbBr3 u DMF-u, uz naknadni tretman inertnim gasom (N2)
u cilju ostvarenja natpritiska, što je omogućilo punjenje nanocevi perovskitnim materijalom. Difuznorefleksiona spektroskopija pokazala je da taloženje CH3NH3PbBr3 poboljšava apsorpciona svojstva
TiO2 nanocevi. I-V karakteristike uzorka pokazale su fotodiodno ponašanje i histerezisnu krivu, koja je
karakteristična za perovskitni materijal. Vrednost struje uzorka snimljenim pod vidljivom svetlošću
iznosila je 46 μA bez primene prednapona, dok je nakon primene prednapona iznosila 76 μA. Rezultati
rada ukazuju da je napravljena perovskitna fotodioda sa povećanim kontaktom između TiO2 i perovskita,
koja predstavlja osnovu za buduću konstrukciju solarnih ćelija., Organic-inorganic perovskites have attracted much attention from researchers due to their high absorption in the visible part of the spectrum and low-cost fabrication. After absorption of the light, electron-hole pairs are formed. To separate electron-hole pairs and reduce recombination, perovskite is combined with TiO2 which has as a consequence, a spontaneous transition of electrons from perovskite to TiO2. This research aims to increase the contact surface of perovskite and TiO2 nanotubes by filling the nanotubes with perovskite material. The solution of methylammonium lead bromide perovskite (CH3NH3PbBr3) in dimethylformamide (DMF) was deposited on anodically synthesized TiO2 nanotubes by the high vacuum system and inert gas. The procedure involved degassation of the sample under high vacuum for 3 h at 200 °C, cooling of the sample, and putting the solution of CH3NH3PbBr3 in DMF, after which it was treated with inert gas (N2), as an overpressure which enabled the filling of the nanotubes with perovskite material. The diffuse reflectance spectroscopy measurement of the sample proved that deposition of CH3NH3PbBr3 improves the absorption properties of TiO2 nanotubes. The I-V characteristics of the sample showed photodiode behavior and characteristic hysteresis curve for perovskite material. The value of current under visible light for the sample without preconditioning was 46 mA, while after preconditioning value of current was 76 mA. The results indicate that a perovskite photodiode with increased contact between TiO2 and perovskite was made, which is the basis for future solar cell construction.",
publisher = "Savez inženjera i tehničara Srbije",
journal = "Tehnika",
title = "Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora, Improvement of absorption properties of TiO2 nanotubes by using CH3NH3PbBr3 perovskite as photosensitizer",
pages = "21-15",
number = "1",
volume = "31",
doi = "10.5937/tehnika2201015S"
}
Stefanović, M. P., Vujančević, J. D., Petrović, R. P., Stevanović, M. S.,& Janaćković, Đ. T.. (2022). Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora. in Tehnika
Savez inženjera i tehničara Srbije., 31(1), 15-21.
https://doi.org/10.5937/tehnika2201015S
Stefanović MP, Vujančević JD, Petrović RP, Stevanović MS, Janaćković ĐT. Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora. in Tehnika. 2022;31(1):15-21.
doi:10.5937/tehnika2201015S .
Stefanović, Milica P., Vujančević, Jelena D., Petrović, Rada P., Stevanović, Marija S., Janaćković, Đorđe T., "Poboljšanje apsorpcionih svojstava TiO2 nanocevi pomoću CH3NH3PbBr3 perovskita kao fotosenzitivizatora" in Tehnika, 31, no. 1 (2022):15-21,
https://doi.org/10.5937/tehnika2201015S . .