TY  - JOUR
AU  - Krivokapić, Jovana
AU  - Ivanović, Jasna
AU  - Đuriš, Jelena
AU  - Medarević, Đorđe
AU  - Potpara, Zorica
AU  - Maksimović, Zoran
AU  - Ibrić, Svetlana
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5900
AB  - The objective of this work was to study the relation between the manufacturing conditions of microcrystalline cellulose (MCC), its physicochemical properties and its tableting behavior. Two different preparation procedures were used to produce MCC from wheat straw, utilizing an acid hydrolysis method, either using only sulfuric acid or combination of sulfuric and hydrochloric acid. The tableting behavior of obtained MCC samples and mixtures of MCC with ibuprofen was studied using a dynamic powder compaction analyzer. It was observed that some of the obtained MCC samples showed better flowing properties than commercially available Vivapur® PH101 and also very high values of tensile strength, solid fraction and elastic recovery. This can be linked with its good compaction behavior, but on the other hand it can cause problems with the disintegration of the tablets. In mixtures with ibuprofen, MCC samples showed lower values of tensile strength, while on the other hand elastic recovery did not seem to be much affected, still exhibiting very high values. According to the obtained results, it can be concluded that MCC obtained from the agricultural waste could have satisfactory properties for tablet preparation by the direct compression method. Further studies are needed to optimize process conditions in order to achieve better physicochemical characteristics, especially in terms of elastic recovery.
PB  - Elsevier B.V.
T2  - Saudi Pharmaceutical Journal
T1  - Tableting properties of microcrystalline cellulose obtained from wheat straw measured with a single punch bench top tablet press
EP  - 718
SP  - 710
VL  - 2
DO  - 10.1016/j.jsps.2020.04.013
ER  - 

@article{
author = "Krivokapić, Jovana and Ivanović, Jasna and Đuriš, Jelena and Medarević, Đorđe and Potpara, Zorica and Maksimović, Zoran and Ibrić, Svetlana",
year = "2020",
abstract = "The objective of this work was to study the relation between the manufacturing conditions of microcrystalline cellulose (MCC), its physicochemical properties and its tableting behavior. Two different preparation procedures were used to produce MCC from wheat straw, utilizing an acid hydrolysis method, either using only sulfuric acid or combination of sulfuric and hydrochloric acid. The tableting behavior of obtained MCC samples and mixtures of MCC with ibuprofen was studied using a dynamic powder compaction analyzer. It was observed that some of the obtained MCC samples showed better flowing properties than commercially available Vivapur® PH101 and also very high values of tensile strength, solid fraction and elastic recovery. This can be linked with its good compaction behavior, but on the other hand it can cause problems with the disintegration of the tablets. In mixtures with ibuprofen, MCC samples showed lower values of tensile strength, while on the other hand elastic recovery did not seem to be much affected, still exhibiting very high values. According to the obtained results, it can be concluded that MCC obtained from the agricultural waste could have satisfactory properties for tablet preparation by the direct compression method. Further studies are needed to optimize process conditions in order to achieve better physicochemical characteristics, especially in terms of elastic recovery.",
publisher = "Elsevier B.V.",
journal = "Saudi Pharmaceutical Journal",
title = "Tableting properties of microcrystalline cellulose obtained from wheat straw measured with a single punch bench top tablet press",
pages = "718-710",
volume = "2",
doi = "10.1016/j.jsps.2020.04.013"
}

Krivokapić, J., Ivanović, J., Đuriš, J., Medarević, Đ., Potpara, Z., Maksimović, Z.,& Ibrić, S.. (2020). Tableting properties of microcrystalline cellulose obtained from wheat straw measured with a single punch bench top tablet press. in Saudi Pharmaceutical Journal
Elsevier B.V.., 2, 710-718.
https://doi.org/10.1016/j.jsps.2020.04.013

Krivokapić J, Ivanović J, Đuriš J, Medarević Đ, Potpara Z, Maksimović Z, Ibrić S. Tableting properties of microcrystalline cellulose obtained from wheat straw measured with a single punch bench top tablet press. in Saudi Pharmaceutical Journal. 2020;2:710-718.
doi:10.1016/j.jsps.2020.04.013 .

Krivokapić, Jovana, Ivanović, Jasna, Đuriš, Jelena, Medarević, Đorđe, Potpara, Zorica, Maksimović, Zoran, Ibrić, Svetlana, "Tableting properties of microcrystalline cellulose obtained from wheat straw measured with a single punch bench top tablet press" in Saudi Pharmaceutical Journal, 2 (2020):710-718,
https://doi.org/10.1016/j.jsps.2020.04.013 . .

TY  - JOUR
AU  - Milovanović, Stoja
AU  - Đuriš, Jelena
AU  - Dapčević, Aleksandra
AU  - Medarević, Đorđe
AU  - Ibrić, Svetlana
AU  - Žižović, Irena
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4074
AB  - The present work is aimed towards designing advanced materials by means of sustainable processes. In that sense, the utilization of supercritical CO2 (scCO(2)) for processing of pharmaceutical polymers (Soluplus (R), Eudragit (R), and hydroxypropyl methylcellulose acetate succinate), alone and with an addition of cardiovascular drug Carvedilol, was explored. Employed single-step static scCO(2) process (pressure of 30 MPa and temperature of 100 degrees C for 2 h) enabled fabrication of solvent-free polymeric foams and Carvedilol solid dispersions with controlled microstructure and average pore diameter of 101-257 pm suitable for application in the pharmaceutical industry. ScCO2 did not remain in the foams after processing or affected the polymer composition, while Carvedilol formed hydrogen bonds with the polymers. Carvedilol was molecularly dispersed in the fabricated solid dispersions and its transition from the crystalline to amorphous form was complete. Korsmeyer-Peppas model was successfully used for the mathematical description of Carvedilol dissolution from solid dispersions. The dissolution rate of Carvedilol in acidic medium was significantly enhanced by its dispersion in tested polymers using the proposed high-pressure method.
PB  - Elsevier Sci Ltd, Oxford
T2  - Polymer Testing
T1  - Soluplus (R), Eudragit (R), HPMC-AS foams and solid dispersions for enhancement of Carvedilol dissolution rate prepared by a supercritical CO2 process
EP  - 64
SP  - 54
VL  - 76
DO  - 10.1016/j.polymertesting.2019.03.001
ER  - 

@article{
author = "Milovanović, Stoja and Đuriš, Jelena and Dapčević, Aleksandra and Medarević, Đorđe and Ibrić, Svetlana and Žižović, Irena",
year = "2019",
abstract = "The present work is aimed towards designing advanced materials by means of sustainable processes. In that sense, the utilization of supercritical CO2 (scCO(2)) for processing of pharmaceutical polymers (Soluplus (R), Eudragit (R), and hydroxypropyl methylcellulose acetate succinate), alone and with an addition of cardiovascular drug Carvedilol, was explored. Employed single-step static scCO(2) process (pressure of 30 MPa and temperature of 100 degrees C for 2 h) enabled fabrication of solvent-free polymeric foams and Carvedilol solid dispersions with controlled microstructure and average pore diameter of 101-257 pm suitable for application in the pharmaceutical industry. ScCO2 did not remain in the foams after processing or affected the polymer composition, while Carvedilol formed hydrogen bonds with the polymers. Carvedilol was molecularly dispersed in the fabricated solid dispersions and its transition from the crystalline to amorphous form was complete. Korsmeyer-Peppas model was successfully used for the mathematical description of Carvedilol dissolution from solid dispersions. The dissolution rate of Carvedilol in acidic medium was significantly enhanced by its dispersion in tested polymers using the proposed high-pressure method.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Polymer Testing",
title = "Soluplus (R), Eudragit (R), HPMC-AS foams and solid dispersions for enhancement of Carvedilol dissolution rate prepared by a supercritical CO2 process",
pages = "64-54",
volume = "76",
doi = "10.1016/j.polymertesting.2019.03.001"
}

Milovanović, S., Đuriš, J., Dapčević, A., Medarević, Đ., Ibrić, S.,& Žižović, I.. (2019). Soluplus (R), Eudragit (R), HPMC-AS foams and solid dispersions for enhancement of Carvedilol dissolution rate prepared by a supercritical CO2 process. in Polymer Testing
Elsevier Sci Ltd, Oxford., 76, 54-64.
https://doi.org/10.1016/j.polymertesting.2019.03.001

Milovanović S, Đuriš J, Dapčević A, Medarević Đ, Ibrić S, Žižović I. Soluplus (R), Eudragit (R), HPMC-AS foams and solid dispersions for enhancement of Carvedilol dissolution rate prepared by a supercritical CO2 process. in Polymer Testing. 2019;76:54-64.
doi:10.1016/j.polymertesting.2019.03.001 .

Milovanović, Stoja, Đuriš, Jelena, Dapčević, Aleksandra, Medarević, Đorđe, Ibrić, Svetlana, Žižović, Irena, "Soluplus (R), Eudragit (R), HPMC-AS foams and solid dispersions for enhancement of Carvedilol dissolution rate prepared by a supercritical CO2 process" in Polymer Testing, 76 (2019):54-64,
https://doi.org/10.1016/j.polymertesting.2019.03.001 . .

TY  - JOUR
AU  - Đuriš, Jelena
AU  - Milovanović, Stoja
AU  - Medarević, Đorđe
AU  - Dobričić, Vladimir
AU  - Dapčević, Aleksandra
AU  - Ibrić, Svetlana
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4335
AB  - Solid dispersions production is one of the substantial approaches for improvement of poor drug solubility. Additionally, supercritical fluid assisted method for preparation of solid dispersions can offer many advantages in comparison to the conventional melting or solvent-evaporation methods. Miscibility analysis provides valuable guidance for selection of the most appropriate polymeric carrier for dispersion of the drug of interest. In addition to the increased drug release rate, solid dispersions should have proper mechanical attributes in order to be successfully formulated in the final solid dosage form such as tablet. Therefore, several pharmaceutical grade polymers have been selected for development of BCS Class II drug carvedilol (CARV) solid dispersions. They were compared based on behavior in supercritical CO2 and affinity towards CARV calculated from the miscibility analysis. By utilization of the supercritical CO2 assisted method, solid dispersions of CARV with the selected (co) polymers (polyvinylpyrrolidone (PVP), hydroxypropyl methylcellulose (HPMC), Soluplus (R) and Eudragit (R)) were obtained. Properties of the prepared CARV-polymer dispersions were observed by the polarizing and scanning electron microscopy and analyzed by differential scanning calorimetry and Fourier transform infrared spectroscopy. CARV was additionally characterized by X-ray powder diffraction. Furthermore, in vitro dissolution studies and dynamic compaction analysis were performed on the selected samples of solid dispersions. Among the studied polymers, PVP and HPMC have been identified as polymers with the highest affinity towards CARV, based on the calculated delta(p) values. This has been also confirmed with the highest dissolution efficiency of CARV-PVP and CARV-HPMC solid dispersions. Solid state characterization indicated that CARV was dispersed either molecularly, or in the amorphous form, depending on interactions with each polymer. Determination of CARV-PVP and CARV-HPMC mechanical properties revealed that CARV-PVP solid dispersion has superior compactibility and tabletability. Therefore, CARV-PVP solid dispersion has been highlighted as the most appropriate for the further development of tablets as the final dosage form. Presented study provides an example for efficient approach for development of poorly soluble drug solid dispersion with satisfactory tableting properties.
PB  - Elsevier Science Bv, Amsterdam
T2  - International Journal of Pharmaceutics
T1  - Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol solid dispersions
EP  - 200
SP  - 190
VL  - 554
DO  - 10.1016/j.ijpharm.2018.11.015
ER  - 

@article{
author = "Đuriš, Jelena and Milovanović, Stoja and Medarević, Đorđe and Dobričić, Vladimir and Dapčević, Aleksandra and Ibrić, Svetlana",
year = "2019",
abstract = "Solid dispersions production is one of the substantial approaches for improvement of poor drug solubility. Additionally, supercritical fluid assisted method for preparation of solid dispersions can offer many advantages in comparison to the conventional melting or solvent-evaporation methods. Miscibility analysis provides valuable guidance for selection of the most appropriate polymeric carrier for dispersion of the drug of interest. In addition to the increased drug release rate, solid dispersions should have proper mechanical attributes in order to be successfully formulated in the final solid dosage form such as tablet. Therefore, several pharmaceutical grade polymers have been selected for development of BCS Class II drug carvedilol (CARV) solid dispersions. They were compared based on behavior in supercritical CO2 and affinity towards CARV calculated from the miscibility analysis. By utilization of the supercritical CO2 assisted method, solid dispersions of CARV with the selected (co) polymers (polyvinylpyrrolidone (PVP), hydroxypropyl methylcellulose (HPMC), Soluplus (R) and Eudragit (R)) were obtained. Properties of the prepared CARV-polymer dispersions were observed by the polarizing and scanning electron microscopy and analyzed by differential scanning calorimetry and Fourier transform infrared spectroscopy. CARV was additionally characterized by X-ray powder diffraction. Furthermore, in vitro dissolution studies and dynamic compaction analysis were performed on the selected samples of solid dispersions. Among the studied polymers, PVP and HPMC have been identified as polymers with the highest affinity towards CARV, based on the calculated delta(p) values. This has been also confirmed with the highest dissolution efficiency of CARV-PVP and CARV-HPMC solid dispersions. Solid state characterization indicated that CARV was dispersed either molecularly, or in the amorphous form, depending on interactions with each polymer. Determination of CARV-PVP and CARV-HPMC mechanical properties revealed that CARV-PVP solid dispersion has superior compactibility and tabletability. Therefore, CARV-PVP solid dispersion has been highlighted as the most appropriate for the further development of tablets as the final dosage form. Presented study provides an example for efficient approach for development of poorly soluble drug solid dispersion with satisfactory tableting properties.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "International Journal of Pharmaceutics",
title = "Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol solid dispersions",
pages = "200-190",
volume = "554",
doi = "10.1016/j.ijpharm.2018.11.015"
}

Đuriš, J., Milovanović, S., Medarević, Đ., Dobričić, V., Dapčević, A.,& Ibrić, S.. (2019). Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol solid dispersions. in International Journal of Pharmaceutics
Elsevier Science Bv, Amsterdam., 554, 190-200.
https://doi.org/10.1016/j.ijpharm.2018.11.015

Đuriš J, Milovanović S, Medarević Đ, Dobričić V, Dapčević A, Ibrić S. Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol solid dispersions. in International Journal of Pharmaceutics. 2019;554:190-200.
doi:10.1016/j.ijpharm.2018.11.015 .

Đuriš, Jelena, Milovanović, Stoja, Medarević, Đorđe, Dobričić, Vladimir, Dapčević, Aleksandra, Ibrić, Svetlana, "Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol solid dispersions" in International Journal of Pharmaceutics, 554 (2019):190-200,
https://doi.org/10.1016/j.ijpharm.2018.11.015 . .

TY  - JOUR
AU  - Djuris, Jelena
AU  - Milovanovic, Stoja
AU  - Medarevic, Djordje
AU  - Dobricic, Vladimir
AU  - Dapčević, Aleksandra
AU  - Ibric, Svetlana
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5030
AB  - Solid dispersions production is one of the substantial approaches for improvement of poor drug solubility. Additionally, supercritical fluid assisted method for preparation of solid dispersions can offer many advantages in comparison to the conventional melting or solvent-evaporation methods. Miscibility analysis provides valuable guidance for selection of the most appropriate polymeric carrier for dispersion of the drug of interest. In addition to the increased drug release rate, solid dispersions should have proper mechanical attributes in order to be successfully formulated in the final solid dosage form such as tablet. Therefore, several pharmaceutical grade polymers have been selected for development of BCS Class II drug carvedilol (CARV) solid dispersions. They were compared based on behavior in supercritical CO 2 and affinity towards CARV calculated from the miscibility analysis. By utilization of the supercritical CO 2 assisted method, solid dispersions of CARV with the selected (co)polymers (polyvinylpyrrolidone (PVP), hydroxypropyl methylcellulose (HPMC), Soluplus® and Eudragit®) were obtained. Properties of the prepared CARV-polymer dispersions were observed by the polarizing and scanning electron microscopy and analyzed by differential scanning calorimetry and Fourier transform infrared spectroscopy. CARV was additionally characterized by X-ray powder diffraction. Furthermore, in vitro dissolution studies and dynamic compaction analysis were performed on the selected samples of solid dispersions. Among the studied polymers, PVP and HPMC have been identified as polymers with the highest affinity towards CARV, based on the calculated δ p values. This has been also confirmed with the highest dissolution efficiency of CARV-PVP and CARV-HPMC solid dispersions. Solid state characterization indicated that CARV was dispersed either molecularly, or in the amorphous form, depending on interactions with each polymer. Determination of CARV-PVP and CARV-HPMC mechanical properties revealed that CARV-PVP solid dispersion has superior compactibility and tabletability. Therefore, CARV-PVP solid dispersion has been highlighted as the most appropriate for the further development of tablets as the final dosage form. Presented study provides an example for efficient approach for development of poorly soluble drug solid dispersion with satisfactory tableting properties.
PB  - Elsevier B.V.
T2  - International Journal of Pharmaceutics
T1  - Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol  solid dispersions
EP  - 200
SP  - 190
VL  - 554
DO  - 10.1016/j.ijpharm.2018.11.015
ER  - 

@article{
author = "Djuris, Jelena and Milovanovic, Stoja and Medarevic, Djordje and Dobricic, Vladimir and Dapčević, Aleksandra and Ibric, Svetlana",
year = "2019",
abstract = "Solid dispersions production is one of the substantial approaches for improvement of poor drug solubility. Additionally, supercritical fluid assisted method for preparation of solid dispersions can offer many advantages in comparison to the conventional melting or solvent-evaporation methods. Miscibility analysis provides valuable guidance for selection of the most appropriate polymeric carrier for dispersion of the drug of interest. In addition to the increased drug release rate, solid dispersions should have proper mechanical attributes in order to be successfully formulated in the final solid dosage form such as tablet. Therefore, several pharmaceutical grade polymers have been selected for development of BCS Class II drug carvedilol (CARV) solid dispersions. They were compared based on behavior in supercritical CO 2 and affinity towards CARV calculated from the miscibility analysis. By utilization of the supercritical CO 2 assisted method, solid dispersions of CARV with the selected (co)polymers (polyvinylpyrrolidone (PVP), hydroxypropyl methylcellulose (HPMC), Soluplus® and Eudragit®) were obtained. Properties of the prepared CARV-polymer dispersions were observed by the polarizing and scanning electron microscopy and analyzed by differential scanning calorimetry and Fourier transform infrared spectroscopy. CARV was additionally characterized by X-ray powder diffraction. Furthermore, in vitro dissolution studies and dynamic compaction analysis were performed on the selected samples of solid dispersions. Among the studied polymers, PVP and HPMC have been identified as polymers with the highest affinity towards CARV, based on the calculated δ p values. This has been also confirmed with the highest dissolution efficiency of CARV-PVP and CARV-HPMC solid dispersions. Solid state characterization indicated that CARV was dispersed either molecularly, or in the amorphous form, depending on interactions with each polymer. Determination of CARV-PVP and CARV-HPMC mechanical properties revealed that CARV-PVP solid dispersion has superior compactibility and tabletability. Therefore, CARV-PVP solid dispersion has been highlighted as the most appropriate for the further development of tablets as the final dosage form. Presented study provides an example for efficient approach for development of poorly soluble drug solid dispersion with satisfactory tableting properties.",
publisher = "Elsevier B.V.",
journal = "International Journal of Pharmaceutics",
title = "Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol  solid dispersions",
pages = "200-190",
volume = "554",
doi = "10.1016/j.ijpharm.2018.11.015"
}

Djuris, J., Milovanovic, S., Medarevic, D., Dobricic, V., Dapčević, A.,& Ibric, S.. (2019). Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol  solid dispersions. in International Journal of Pharmaceutics
Elsevier B.V.., 554, 190-200.
https://doi.org/10.1016/j.ijpharm.2018.11.015

Djuris J, Milovanovic S, Medarevic D, Dobricic V, Dapčević A, Ibric S. Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol  solid dispersions. in International Journal of Pharmaceutics. 2019;554:190-200.
doi:10.1016/j.ijpharm.2018.11.015 .

Djuris, Jelena, Milovanovic, Stoja, Medarevic, Djordje, Dobricic, Vladimir, Dapčević, Aleksandra, Ibric, Svetlana, "Selection of the suitable polymer for supercritical fluid assisted preparation of carvedilol  solid dispersions" in International Journal of Pharmaceutics, 554 (2019):190-200,
https://doi.org/10.1016/j.ijpharm.2018.11.015 . .

TY  - JOUR
AU  - Krstić, Marko
AU  - Radojević, Marija
AU  - Stojanović, Dušica
AU  - Radojević, Vesna
AU  - Uskoković, Petar
AU  - Ibrić, Svetlana
PY  - 2017
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3749
AB  - The preparation and characterization of films and nanofibers with carvedilol as a poorly water-soluble drug in poly (ethylene oxide) (PEO) polymer were investigated. Films are prepared by solution casting method, and nanofibers by electrospinning from a polymer solution. Water and mixture of ethanol and water were used as solvents. FT-IR analysis of the samples showed that there was no interaction between the polymer and the drug substance. DSC analysis revealed that carvedilol was dissolved in the polymer and influenced the degree of crystallinity of PEO. Carvedilol release rate for all of the formulations was increased in comparison with pure carvedilol. Significant differences in the rate of release of carvedilol from the films and nanofibers were observed. Field Emission Scanning Electron Microscope (FESEM) images of the obtained fiber was revealed the dependence of the fiber diameter of formulation and electrospinning process parameters, and consequently influence the amount and distribution of carvedilol in the encapsulated fibers.
PB  - Elsevier Science Bv, Amsterdam
T2  - European Journal of Pharmaceutical Sciences
T1  - Formulation and characterization of nanofibers and films with carvedilol prepared by electrospinning and solution casting method
EP  - 166
SP  - 160
VL  - 101
DO  - 10.1016/j.ejps.2017.02.006
ER  - 

@article{
author = "Krstić, Marko and Radojević, Marija and Stojanović, Dušica and Radojević, Vesna and Uskoković, Petar and Ibrić, Svetlana",
year = "2017",
abstract = "The preparation and characterization of films and nanofibers with carvedilol as a poorly water-soluble drug in poly (ethylene oxide) (PEO) polymer were investigated. Films are prepared by solution casting method, and nanofibers by electrospinning from a polymer solution. Water and mixture of ethanol and water were used as solvents. FT-IR analysis of the samples showed that there was no interaction between the polymer and the drug substance. DSC analysis revealed that carvedilol was dissolved in the polymer and influenced the degree of crystallinity of PEO. Carvedilol release rate for all of the formulations was increased in comparison with pure carvedilol. Significant differences in the rate of release of carvedilol from the films and nanofibers were observed. Field Emission Scanning Electron Microscope (FESEM) images of the obtained fiber was revealed the dependence of the fiber diameter of formulation and electrospinning process parameters, and consequently influence the amount and distribution of carvedilol in the encapsulated fibers.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "European Journal of Pharmaceutical Sciences",
title = "Formulation and characterization of nanofibers and films with carvedilol prepared by electrospinning and solution casting method",
pages = "166-160",
volume = "101",
doi = "10.1016/j.ejps.2017.02.006"
}

Krstić, M., Radojević, M., Stojanović, D., Radojević, V., Uskoković, P.,& Ibrić, S.. (2017). Formulation and characterization of nanofibers and films with carvedilol prepared by electrospinning and solution casting method. in European Journal of Pharmaceutical Sciences
Elsevier Science Bv, Amsterdam., 101, 160-166.
https://doi.org/10.1016/j.ejps.2017.02.006

Krstić M, Radojević M, Stojanović D, Radojević V, Uskoković P, Ibrić S. Formulation and characterization of nanofibers and films with carvedilol prepared by electrospinning and solution casting method. in European Journal of Pharmaceutical Sciences. 2017;101:160-166.
doi:10.1016/j.ejps.2017.02.006 .

Krstić, Marko, Radojević, Marija, Stojanović, Dušica, Radojević, Vesna, Uskoković, Petar, Ibrić, Svetlana, "Formulation and characterization of nanofibers and films with carvedilol prepared by electrospinning and solution casting method" in European Journal of Pharmaceutical Sciences, 101 (2017):160-166,
https://doi.org/10.1016/j.ejps.2017.02.006 . .

TY  - JOUR
AU  - Marić, Ljiljana B.
AU  - Jović, Branislav D.
AU  - Petrović, Slobodan
AU  - Nikolić, Aleksandar M.
AU  - Homsek, Irena J.
PY  - 2014
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/2840
AB  - This paper reports the use of near infrared (NIR) spectroscopy as a process analytical technology (PAT) tool for monitoring the metformin (N,N-dimethylimidodicarbonimidic diamide) hydrochloride and poly(vinyl pyrrolidone) (PVP) mixing process, which is the first stage in tablet production. Blend homogeneity was tested using the non-invasive NIR spectroscopy method and the partial least squares (PLS) regression model was applied for the analysis of the obtained spectra. Simultaneously, the critical parameter (metformin hydrochloride content) was monitored by a classical analytical technique, the validated HPLC method, commonly used for this purpose. Based on the high sensitivity of the model developed in this study, as well as the established correlation among the results obtained by different methods, it could be concluded that the proposed rapid and non-invasive technique. could be an effecttive tool for the monitoring of one of the critical manufacturing steps in the production solid dosage forms.
PB  - Srpsko hemijsko društvo, Beograd
T2  - Journal of the Serbian Chemical Society
T1  - The application of NIR spectroscopy with chemometric analysis for monitoring a powder blending process
EP  - 340
IS  - 3
SP  - 331
VL  - 79
DO  - 10.2298/JSC010413080M
ER  - 

@article{
author = "Marić, Ljiljana B. and Jović, Branislav D. and Petrović, Slobodan and Nikolić, Aleksandar M. and Homsek, Irena J.",
year = "2014",
abstract = "This paper reports the use of near infrared (NIR) spectroscopy as a process analytical technology (PAT) tool for monitoring the metformin (N,N-dimethylimidodicarbonimidic diamide) hydrochloride and poly(vinyl pyrrolidone) (PVP) mixing process, which is the first stage in tablet production. Blend homogeneity was tested using the non-invasive NIR spectroscopy method and the partial least squares (PLS) regression model was applied for the analysis of the obtained spectra. Simultaneously, the critical parameter (metformin hydrochloride content) was monitored by a classical analytical technique, the validated HPLC method, commonly used for this purpose. Based on the high sensitivity of the model developed in this study, as well as the established correlation among the results obtained by different methods, it could be concluded that the proposed rapid and non-invasive technique. could be an effecttive tool for the monitoring of one of the critical manufacturing steps in the production solid dosage forms.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "Journal of the Serbian Chemical Society",
title = "The application of NIR spectroscopy with chemometric analysis for monitoring a powder blending process",
pages = "340-331",
number = "3",
volume = "79",
doi = "10.2298/JSC010413080M"
}

Marić, L. B., Jović, B. D., Petrović, S., Nikolić, A. M.,& Homsek, I. J.. (2014). The application of NIR spectroscopy with chemometric analysis for monitoring a powder blending process. in Journal of the Serbian Chemical Society
Srpsko hemijsko društvo, Beograd., 79(3), 331-340.
https://doi.org/10.2298/JSC010413080M

Marić LB, Jović BD, Petrović S, Nikolić AM, Homsek IJ. The application of NIR spectroscopy with chemometric analysis for monitoring a powder blending process. in Journal of the Serbian Chemical Society. 2014;79(3):331-340.
doi:10.2298/JSC010413080M .

Marić, Ljiljana B., Jović, Branislav D., Petrović, Slobodan, Nikolić, Aleksandar M., Homsek, Irena J., "The application of NIR spectroscopy with chemometric analysis for monitoring a powder blending process" in Journal of the Serbian Chemical Society, 79, no. 3 (2014):331-340,
https://doi.org/10.2298/JSC010413080M . .