TY  - JOUR
AU  - Karić, Nataša
AU  - Rusmirović, Jelena
AU  - Đolić, Maja
AU  - Kovačević, Tihomir
AU  - Pecić, Ljiljana
AU  - Radovanović, Željko
AU  - Marinković, Aleksandar
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4487
AB  - Oxidized starch, an additive used in paper manufacturing and products for construction industry, is usually produced using harmful oxidant, such as hypochlorites or periodates. In this study, a simple and efficient eco-friendly laboratory and industrial procedures for starch oxidation were developed. The procedure involves application of small amounts of more environmentally friendly oxidant, hydrogen peroxide, a novel special metal complex catalyst such as copper(II) citrate and copper(II) ricinoleate and biobased plasticizers. Optimization procedure, with respect to the quantity of hydrogen peroxide and temperature in the presence of iron(II) sulphate catalyst, was performed by using the response surface methodology. Comparative analysis of the use of the other catalysts that is copper(II) sulphate, copper(II) citrate and copper(II) ricinoleate, indicated copper(II) citrate as the catalyst of choice. Improvement of starch is achieved using three plasticizers: ricinoleic acid (RA), diisopropyl tartarate, as well as epoxidized soybean, linseed and sunflower oils. The effects of hydrogen peroxide and catalyst concentrations, as well as the reaction temperature in the presence of naturally based plasticizers on the physicochemical, thermal and morphological properties of oxidized starch are presented. According to the results obtained in initial experiments, the optimal industrial process is based on the use of copper(II) citrate (0.1 %) as a catalyst and RA (3 %) as a plasticizer.
PB  - Savez hemijskih inženjera, Beograd
T2  - Hemijska industrija
T1  - Preparation and properties of hydrogen peroxide oxidized starch for industrial use
EP  - 36
IS  - 1
SP  - 25
VL  - 74
DO  - 10.2298/HEMIND190722004K
ER  - 

@article{
author = "Karić, Nataša and Rusmirović, Jelena and Đolić, Maja and Kovačević, Tihomir and Pecić, Ljiljana and Radovanović, Željko and Marinković, Aleksandar",
year = "2020",
abstract = "Oxidized starch, an additive used in paper manufacturing and products for construction industry, is usually produced using harmful oxidant, such as hypochlorites or periodates. In this study, a simple and efficient eco-friendly laboratory and industrial procedures for starch oxidation were developed. The procedure involves application of small amounts of more environmentally friendly oxidant, hydrogen peroxide, a novel special metal complex catalyst such as copper(II) citrate and copper(II) ricinoleate and biobased plasticizers. Optimization procedure, with respect to the quantity of hydrogen peroxide and temperature in the presence of iron(II) sulphate catalyst, was performed by using the response surface methodology. Comparative analysis of the use of the other catalysts that is copper(II) sulphate, copper(II) citrate and copper(II) ricinoleate, indicated copper(II) citrate as the catalyst of choice. Improvement of starch is achieved using three plasticizers: ricinoleic acid (RA), diisopropyl tartarate, as well as epoxidized soybean, linseed and sunflower oils. The effects of hydrogen peroxide and catalyst concentrations, as well as the reaction temperature in the presence of naturally based plasticizers on the physicochemical, thermal and morphological properties of oxidized starch are presented. According to the results obtained in initial experiments, the optimal industrial process is based on the use of copper(II) citrate (0.1 %) as a catalyst and RA (3 %) as a plasticizer.",
publisher = "Savez hemijskih inženjera, Beograd",
journal = "Hemijska industrija",
title = "Preparation and properties of hydrogen peroxide oxidized starch for industrial use",
pages = "36-25",
number = "1",
volume = "74",
doi = "10.2298/HEMIND190722004K"
}

Karić, N., Rusmirović, J., Đolić, M., Kovačević, T., Pecić, L., Radovanović, Ž.,& Marinković, A.. (2020). Preparation and properties of hydrogen peroxide oxidized starch for industrial use. in Hemijska industrija
Savez hemijskih inženjera, Beograd., 74(1), 25-36.
https://doi.org/10.2298/HEMIND190722004K

Karić N, Rusmirović J, Đolić M, Kovačević T, Pecić L, Radovanović Ž, Marinković A. Preparation and properties of hydrogen peroxide oxidized starch for industrial use. in Hemijska industrija. 2020;74(1):25-36.
doi:10.2298/HEMIND190722004K .

Karić, Nataša, Rusmirović, Jelena, Đolić, Maja, Kovačević, Tihomir, Pecić, Ljiljana, Radovanović, Željko, Marinković, Aleksandar, "Preparation and properties of hydrogen peroxide oxidized starch for industrial use" in Hemijska industrija, 74, no. 1 (2020):25-36,
https://doi.org/10.2298/HEMIND190722004K . .

TY  - JOUR
AU  - Popović, Ana L.
AU  - Rusmirović, Jelena
AU  - Veličković, Zlate
AU  - Radovanović, Željko
AU  - Ristić, Mirjana
AU  - Pavlović, Vera P.
AU  - Marinković, Aleksandar
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4540
AB  - Novel highly effective amino-functionalized lignin-based biosorbent in the microsphere geometry (A-LMS) for removal of heavy metal ions, was synthesized via inverse suspension copolymerization of kraft lignin with poly(ethylene imine) grafting-agent and epoxy chloropropane cross-linker. Optimization of A-LMS synthesis, performed with respect to the quantity of sodium alginate emulsifier (1, 5 and 10 wt%), provides highly porous microspheres A-LMS_5, using 5 wt% emulsifier, with 800 +/- 80 mu m diameter, 7.68 m(2) g(-1) surface area and 7.7 mmol g(-1) of terminal amino groups. Structural and surface characteristics were obtained from Brunauer-Emmett-Teller method, Fourier Transform-Infrared spectroscopy, scanning electron microscopy, X-ray photo-electron spectroscopy and porosity determination. In a batch test, the influence of pH, A-LMS_5 dose, temperature, contact time on adsorption efficiency of Ni2+, Cd2+, As(V) and Cr(VI) ions were studied. The adsorption is spontaneous and feasible with maximum adsorption capacity of 74.84, 54.20, 53.12 and 49.42 mg g(-1) for Cd2+, Cr(VI), As(V) and Ni2+ ions, respectively, obtained by using Langmuir model. Modeling of kinetic data indicated fast adsorbate removal rate with pore diffusional transport as rate limiting step (pseudo-second order model and Weber-Morris equations), thus further confirming high performances of produced bio-adsorbent for heavy metal ions removal.
PB  - Elsevier, Amsterdam
T2  - International Journal of Biological Macromolecules
T1  - Novel amino-functionalized lignin microspheres: High performance biosorbent with enhanced capacity for heavy metal ion removal
EP  - 1173
SP  - 1160
VL  - 156
DO  - 10.1016/j.ijbiomac.2019.11.152
ER  - 

@article{
author = "Popović, Ana L. and Rusmirović, Jelena and Veličković, Zlate and Radovanović, Željko and Ristić, Mirjana and Pavlović, Vera P. and Marinković, Aleksandar",
year = "2020",
abstract = "Novel highly effective amino-functionalized lignin-based biosorbent in the microsphere geometry (A-LMS) for removal of heavy metal ions, was synthesized via inverse suspension copolymerization of kraft lignin with poly(ethylene imine) grafting-agent and epoxy chloropropane cross-linker. Optimization of A-LMS synthesis, performed with respect to the quantity of sodium alginate emulsifier (1, 5 and 10 wt%), provides highly porous microspheres A-LMS_5, using 5 wt% emulsifier, with 800 +/- 80 mu m diameter, 7.68 m(2) g(-1) surface area and 7.7 mmol g(-1) of terminal amino groups. Structural and surface characteristics were obtained from Brunauer-Emmett-Teller method, Fourier Transform-Infrared spectroscopy, scanning electron microscopy, X-ray photo-electron spectroscopy and porosity determination. In a batch test, the influence of pH, A-LMS_5 dose, temperature, contact time on adsorption efficiency of Ni2+, Cd2+, As(V) and Cr(VI) ions were studied. The adsorption is spontaneous and feasible with maximum adsorption capacity of 74.84, 54.20, 53.12 and 49.42 mg g(-1) for Cd2+, Cr(VI), As(V) and Ni2+ ions, respectively, obtained by using Langmuir model. Modeling of kinetic data indicated fast adsorbate removal rate with pore diffusional transport as rate limiting step (pseudo-second order model and Weber-Morris equations), thus further confirming high performances of produced bio-adsorbent for heavy metal ions removal.",
publisher = "Elsevier, Amsterdam",
journal = "International Journal of Biological Macromolecules",
title = "Novel amino-functionalized lignin microspheres: High performance biosorbent with enhanced capacity for heavy metal ion removal",
pages = "1173-1160",
volume = "156",
doi = "10.1016/j.ijbiomac.2019.11.152"
}

Popović, A. L., Rusmirović, J., Veličković, Z., Radovanović, Ž., Ristić, M., Pavlović, V. P.,& Marinković, A.. (2020). Novel amino-functionalized lignin microspheres: High performance biosorbent with enhanced capacity for heavy metal ion removal. in International Journal of Biological Macromolecules
Elsevier, Amsterdam., 156, 1160-1173.
https://doi.org/10.1016/j.ijbiomac.2019.11.152

Popović AL, Rusmirović J, Veličković Z, Radovanović Ž, Ristić M, Pavlović VP, Marinković A. Novel amino-functionalized lignin microspheres: High performance biosorbent with enhanced capacity for heavy metal ion removal. in International Journal of Biological Macromolecules. 2020;156:1160-1173.
doi:10.1016/j.ijbiomac.2019.11.152 .

Popović, Ana L., Rusmirović, Jelena, Veličković, Zlate, Radovanović, Željko, Ristić, Mirjana, Pavlović, Vera P., Marinković, Aleksandar, "Novel amino-functionalized lignin microspheres: High performance biosorbent with enhanced capacity for heavy metal ion removal" in International Journal of Biological Macromolecules, 156 (2020):1160-1173,
https://doi.org/10.1016/j.ijbiomac.2019.11.152 . .

TY  - JOUR
AU  - Mijatović, Nevenka
AU  - Terzić, Anja
AU  - Miličić, Ljiljana
AU  - Živojinović, Dragana
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4557
AB  - Natural zeolite and bentonite were utilized as mineral additives in the mix-design of environmentally safe cement-based building materials. The adsorptive abilities of these two clayey raw materials, i.e. their affinity to immobilize heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ were investigated. Singleand multi-solutions of Zn2+, Ni2+, Pb2+ and Cu2+ were prepared for the experiment. The obtained results were submitted to analysis via pseudo-first and pseudo-second order kinetic models. Langmuir and Freundlich isotherms were analyzed. Bentonite exhibited better adsorption affinity than zeolite towards all four investigated cations. As a proof, a leaching test was conducted on seven different cement binders with different mineral additives (fly ash, zeolite, bentonite). The leachates obtained on the samples of cement with addition of fly ash and clay (either zeolite or bentonite) contained lower concentrations of Zn2+, Ni2+, Pb2+ and Cu2+ ions than leachates obtained on the samples of cement binder with fly ash solely as a result of adsorption and hydration mechanisms that immobilized heavy metals within cementitious composites.
AB  - Prirodni zeolit i bentonit korišćeni su kao mineralni dodaci u mešavinskom dizajnu ekološki sigurnih građevinskih materijala na bazi cementa. Ispitane su adsorptivne sposobnosti ove dve glinene sirovine, tj. njihov afinitet da imobiliziraju jone teških metala Zn2+, Ni2+, Pb2+ i Cu2+. Za eksperiment su pripremljeni pojedinačni i multi-rastvori Zn2+, Ni2+, Pb2+ i Cu2+ . Dobijeni rezultati su analizirani pomoću kinetičkih modela pseudo prvog i pseudo drugog reda. Analizirane su izoterme Langmuira i Freundlicha. Bentonit je pokazao bolji adsorpcioni afinitet od zeolita prema sva četiri ispitivana katjona. Kao dokaz, ispitano je ispitivanje ispiranja na sedam različitih veziva za cement sa različitim mineralnim dodacima (leteći pepeo, zeolit, bentonit). Eluati dobijeni na uzorcima cementa sa dodatkom letećeg pepela i gline (bilo zeolita ili bentonita) sadržavale su niže koncentracije jona Zn2+, Ni2+, Pb2+ i Cu2+ u odnosu na eluat dobijen na uzorcima cementnog veziva sa letećim pepelom. Razlog za dobijanje ovakvih rezultata su adsorpcioni i hidratacioni mehanizmi koji imobiliziraju teške metale u cementnim kompozitima.
PB  - Engineering Society for Corrosion, Belgrade, Serbia
T2  - Zaštita materijala
T1  - Immobilization of heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ in the structure of cement-based materials
T1  - Imobilizacija teških metalnih jona Zn2+, Ni2+, Pb2+ i Cu2+ u strukturi materijala na bazi cementa
EP  - 127
IS  - 2
SP  - 116
VL  - 61
DO  - 10.5937/zasmat2002116M
ER  - 

@article{
author = "Mijatović, Nevenka and Terzić, Anja and Miličić, Ljiljana and Živojinović, Dragana",
year = "2020",
abstract = "Natural zeolite and bentonite were utilized as mineral additives in the mix-design of environmentally safe cement-based building materials. The adsorptive abilities of these two clayey raw materials, i.e. their affinity to immobilize heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ were investigated. Singleand multi-solutions of Zn2+, Ni2+, Pb2+ and Cu2+ were prepared for the experiment. The obtained results were submitted to analysis via pseudo-first and pseudo-second order kinetic models. Langmuir and Freundlich isotherms were analyzed. Bentonite exhibited better adsorption affinity than zeolite towards all four investigated cations. As a proof, a leaching test was conducted on seven different cement binders with different mineral additives (fly ash, zeolite, bentonite). The leachates obtained on the samples of cement with addition of fly ash and clay (either zeolite or bentonite) contained lower concentrations of Zn2+, Ni2+, Pb2+ and Cu2+ ions than leachates obtained on the samples of cement binder with fly ash solely as a result of adsorption and hydration mechanisms that immobilized heavy metals within cementitious composites., Prirodni zeolit i bentonit korišćeni su kao mineralni dodaci u mešavinskom dizajnu ekološki sigurnih građevinskih materijala na bazi cementa. Ispitane su adsorptivne sposobnosti ove dve glinene sirovine, tj. njihov afinitet da imobiliziraju jone teških metala Zn2+, Ni2+, Pb2+ i Cu2+. Za eksperiment su pripremljeni pojedinačni i multi-rastvori Zn2+, Ni2+, Pb2+ i Cu2+ . Dobijeni rezultati su analizirani pomoću kinetičkih modela pseudo prvog i pseudo drugog reda. Analizirane su izoterme Langmuira i Freundlicha. Bentonit je pokazao bolji adsorpcioni afinitet od zeolita prema sva četiri ispitivana katjona. Kao dokaz, ispitano je ispitivanje ispiranja na sedam različitih veziva za cement sa različitim mineralnim dodacima (leteći pepeo, zeolit, bentonit). Eluati dobijeni na uzorcima cementa sa dodatkom letećeg pepela i gline (bilo zeolita ili bentonita) sadržavale su niže koncentracije jona Zn2+, Ni2+, Pb2+ i Cu2+ u odnosu na eluat dobijen na uzorcima cementnog veziva sa letećim pepelom. Razlog za dobijanje ovakvih rezultata su adsorpcioni i hidratacioni mehanizmi koji imobiliziraju teške metale u cementnim kompozitima.",
publisher = "Engineering Society for Corrosion, Belgrade, Serbia",
journal = "Zaštita materijala",
title = "Immobilization of heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ in the structure of cement-based materials, Imobilizacija teških metalnih jona Zn2+, Ni2+, Pb2+ i Cu2+ u strukturi materijala na bazi cementa",
pages = "127-116",
number = "2",
volume = "61",
doi = "10.5937/zasmat2002116M"
}

Mijatović, N., Terzić, A., Miličić, L.,& Živojinović, D.. (2020). Immobilization of heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ in the structure of cement-based materials. in Zaštita materijala
Engineering Society for Corrosion, Belgrade, Serbia., 61(2), 116-127.
https://doi.org/10.5937/zasmat2002116M

Mijatović N, Terzić A, Miličić L, Živojinović D. Immobilization of heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ in the structure of cement-based materials. in Zaštita materijala. 2020;61(2):116-127.
doi:10.5937/zasmat2002116M .

Mijatović, Nevenka, Terzić, Anja, Miličić, Ljiljana, Živojinović, Dragana, "Immobilization of heavy metal ions Zn2+, Ni2+, Pb2+ and Cu2+ in the structure of cement-based materials" in Zaštita materijala, 61, no. 2 (2020):116-127,
https://doi.org/10.5937/zasmat2002116M . .

TY  - JOUR
AU  - Stojanović, Nemanja
AU  - Kalezić-Glisović, Aleksandra
AU  - Janićijević, Aco
AU  - Maricić, Aleksa
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4362
AB  - Multiferroic systems are attractive to the researches worldwide due to diversity of existing applications, as well as possible novel ones. In order to contribute to understanding of the processes that take place within the structure of such a system, we subjected it to mechanochemical activation and thermal treatment. Powdery mixtures of iron and barium titanate in a mass ratio of 30% Fe and 70% BaTiO3 were activated in a planetary ball mill for time duration of 30 to 300 min and subsequently sintered at 1200 degrees C in the atmosphere of air. During the activation the system undergoes structural phase transitions, whereby the content of iron and its oxides changes. The highest Fe content was observed in the sample activated for 270 min, with local maxima in crystallite size and microstrain values and a minimum in dislocation density. The complex dielectric permittivity changes in the applied radio frequency field, rangingfrom 176.9 pF/m in thesample activated for 90 min to 918.1 pF/m in the sample activated for 180 min. As the frequency of the field increases, an exponential decrease in the magnetic with a simultaneous increase in the electrical energy losses is noticeable. The system exhibits ferromagnetic resonance, whereby longer activation in the mill shifts the resonant frequency to higher values. Negative electrical resistance was observed in all analyzed samples. The activation time changes both the demagnetization temperature and the Curie temperature of the samples undergoing heating and cooling cycles in the external permanent magnetic field. Curie temperature is the highest in the sample activated for 240 min. Thermal treatment increases the initial magnetization of all samples, with the most pronounced increase of similar to 95% in the sample activated for 300 min.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment
EP  - 176
IS  - 2
SP  - 163
VL  - 52
DO  - 10.2298/SOS2002163S
ER  - 

@article{
author = "Stojanović, Nemanja and Kalezić-Glisović, Aleksandra and Janićijević, Aco and Maricić, Aleksa",
year = "2020",
abstract = "Multiferroic systems are attractive to the researches worldwide due to diversity of existing applications, as well as possible novel ones. In order to contribute to understanding of the processes that take place within the structure of such a system, we subjected it to mechanochemical activation and thermal treatment. Powdery mixtures of iron and barium titanate in a mass ratio of 30% Fe and 70% BaTiO3 were activated in a planetary ball mill for time duration of 30 to 300 min and subsequently sintered at 1200 degrees C in the atmosphere of air. During the activation the system undergoes structural phase transitions, whereby the content of iron and its oxides changes. The highest Fe content was observed in the sample activated for 270 min, with local maxima in crystallite size and microstrain values and a minimum in dislocation density. The complex dielectric permittivity changes in the applied radio frequency field, rangingfrom 176.9 pF/m in thesample activated for 90 min to 918.1 pF/m in the sample activated for 180 min. As the frequency of the field increases, an exponential decrease in the magnetic with a simultaneous increase in the electrical energy losses is noticeable. The system exhibits ferromagnetic resonance, whereby longer activation in the mill shifts the resonant frequency to higher values. Negative electrical resistance was observed in all analyzed samples. The activation time changes both the demagnetization temperature and the Curie temperature of the samples undergoing heating and cooling cycles in the external permanent magnetic field. Curie temperature is the highest in the sample activated for 240 min. Thermal treatment increases the initial magnetization of all samples, with the most pronounced increase of similar to 95% in the sample activated for 300 min.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment",
pages = "176-163",
number = "2",
volume = "52",
doi = "10.2298/SOS2002163S"
}

Stojanović, N., Kalezić-Glisović, A., Janićijević, A.,& Maricić, A.. (2020). Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 52(2), 163-176.
https://doi.org/10.2298/SOS2002163S

Stojanović N, Kalezić-Glisović A, Janićijević A, Maricić A. Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment. in Science of Sintering. 2020;52(2):163-176.
doi:10.2298/SOS2002163S .

Stojanović, Nemanja, Kalezić-Glisović, Aleksandra, Janićijević, Aco, Maricić, Aleksa, "Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment" in Science of Sintering, 52, no. 2 (2020):163-176,
https://doi.org/10.2298/SOS2002163S . .

TY  - JOUR
AU  - Milosević, Dragana L.
AU  - Tomić, Nataša
AU  - Đokić, Veljko
AU  - Vidović, Milka
AU  - Veličković, Zlate
AU  - Jančić-Heinemann, Radmila
AU  - Marinković, Aleksandar
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4506
AB  - The adsorption performance of three-dimensionally ordered macroporous (3DOM) alumina doped with iron oxide, and subsequently modified with (3-aminopropyl)triethoxysilane (APTES), FeAl2O3 and FeAl(2)O(3)APTES, was used for enhanced Pb2+, Cd2+ and Ni2+ removal. The phase composition and the structural and surface/textural properties of the obtained adsorbents were analyzed by X-ray diffraction analysis, field emission scanning electron microscope, energy dispersive X-ray analysis, thermogravimetry, Fourier-transfer infrared spectroscopy, specific surface area of the samples and point of zero charge determination. Adsorption of selected cations was examined in the batch conditions using different contact time, adsorbent dosage and temperatures. Different models of the adsorption isotherms were used for determination of the adsorption capacities, in which the best fit of Freundlich and Langmuir model was obtained for FeAl2O3, that is, Freundlich model for FeAl(2)O(3)APTES. A significant increase of adsorption capacities: from 44.21 to 51.66 mg g(-1) for Pb2+, 25.69 to 32.96 mg g(-1) for Cd2+ and 19.48 to 24.64 mg g(-1) for Ni2+ was obtained for FeAl2O3 and FeAl(2)O(3)APTES, respectively, which indicated the significance of the macroporous structure of 3DOM alumina and subsequent amino-terminal modification. The values of the correlation coefficient (R-2) suggested that pseudo-second kinetic model best describes Pb2+, Cd2+ and Ni2+ adsorption on FeAl(2)O(3)APTES, and Cd2+ and Ni2+ onto FeAl2O3, while second kinetic model gave the highest correlation coefficients for Pb2+ adsorption on FeAl2O3.
PB  - Desalination Publ, Hopkinton
T2  - Desalination and Water Treatment
T1  - Structural and surface modification of highly ordered alumina for enhanced removal of Pb2+, Cd2+ and Ni2+ from aqueous solution
EP  - 239
SP  - 220
VL  - 178
DO  - 10.5004/dwt.2020.24982
ER  - 

@article{
author = "Milosević, Dragana L. and Tomić, Nataša and Đokić, Veljko and Vidović, Milka and Veličković, Zlate and Jančić-Heinemann, Radmila and Marinković, Aleksandar",
year = "2020",
abstract = "The adsorption performance of three-dimensionally ordered macroporous (3DOM) alumina doped with iron oxide, and subsequently modified with (3-aminopropyl)triethoxysilane (APTES), FeAl2O3 and FeAl(2)O(3)APTES, was used for enhanced Pb2+, Cd2+ and Ni2+ removal. The phase composition and the structural and surface/textural properties of the obtained adsorbents were analyzed by X-ray diffraction analysis, field emission scanning electron microscope, energy dispersive X-ray analysis, thermogravimetry, Fourier-transfer infrared spectroscopy, specific surface area of the samples and point of zero charge determination. Adsorption of selected cations was examined in the batch conditions using different contact time, adsorbent dosage and temperatures. Different models of the adsorption isotherms were used for determination of the adsorption capacities, in which the best fit of Freundlich and Langmuir model was obtained for FeAl2O3, that is, Freundlich model for FeAl(2)O(3)APTES. A significant increase of adsorption capacities: from 44.21 to 51.66 mg g(-1) for Pb2+, 25.69 to 32.96 mg g(-1) for Cd2+ and 19.48 to 24.64 mg g(-1) for Ni2+ was obtained for FeAl2O3 and FeAl(2)O(3)APTES, respectively, which indicated the significance of the macroporous structure of 3DOM alumina and subsequent amino-terminal modification. The values of the correlation coefficient (R-2) suggested that pseudo-second kinetic model best describes Pb2+, Cd2+ and Ni2+ adsorption on FeAl(2)O(3)APTES, and Cd2+ and Ni2+ onto FeAl2O3, while second kinetic model gave the highest correlation coefficients for Pb2+ adsorption on FeAl2O3.",
publisher = "Desalination Publ, Hopkinton",
journal = "Desalination and Water Treatment",
title = "Structural and surface modification of highly ordered alumina for enhanced removal of Pb2+, Cd2+ and Ni2+ from aqueous solution",
pages = "239-220",
volume = "178",
doi = "10.5004/dwt.2020.24982"
}

Milosević, D. L., Tomić, N., Đokić, V., Vidović, M., Veličković, Z., Jančić-Heinemann, R.,& Marinković, A.. (2020). Structural and surface modification of highly ordered alumina for enhanced removal of Pb2+, Cd2+ and Ni2+ from aqueous solution. in Desalination and Water Treatment
Desalination Publ, Hopkinton., 178, 220-239.
https://doi.org/10.5004/dwt.2020.24982

Milosević DL, Tomić N, Đokić V, Vidović M, Veličković Z, Jančić-Heinemann R, Marinković A. Structural and surface modification of highly ordered alumina for enhanced removal of Pb2+, Cd2+ and Ni2+ from aqueous solution. in Desalination and Water Treatment. 2020;178:220-239.
doi:10.5004/dwt.2020.24982 .

Milosević, Dragana L., Tomić, Nataša, Đokić, Veljko, Vidović, Milka, Veličković, Zlate, Jančić-Heinemann, Radmila, Marinković, Aleksandar, "Structural and surface modification of highly ordered alumina for enhanced removal of Pb2+, Cd2+ and Ni2+ from aqueous solution" in Desalination and Water Treatment, 178 (2020):220-239,
https://doi.org/10.5004/dwt.2020.24982 . .

TY  - JOUR
AU  - Stevanović, Maja
AU  - Bajić, Zoran J.
AU  - Veličković, Zlate
AU  - Karkalić, Radovan
AU  - Pecić, Ljiljana
AU  - Otrisal, Pavel
AU  - Marinković, Aleksandar
PY  - 2020
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4507
AB  - The synthesis and adsorption potential of Cy-npAg, obtained by modification of raw montmorillonite clay (raw-Cy) with silver nanoparticle (npAg), was studied in this work. Optimization procedure, with respect to time, temperature and amount of deposit npAg, obtained either by reductive precipitation or ultraviolet irradiation, was performed using response surface methodology (RSM). The most efficient adsorbent, obtained by chemical reduction of silver ion with sodium borohydride, named Cy-npAg, was characterized in detail using Brunauer-Emmett-Teller, scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction techniques, and point of zero charge determination. The Cy-npAg showed good adsorption capacity with respect to non-systemic organophosphate insecticide (diazinon) as well as of heavy metals ions (Cd2+ and Ni2+ ions), that is, 74.26, 62.33, and 35.49 mg g(-1), respectively, obtained from Langmuir model fitting. Temperature dependent kinetic study allowed determination of pseudo-second rate constant (10(3) g mg(-1) min(-1))/activation energies (kJ mol(-1)): 1.45/14.48 for diazinon, and 1.27/6.59 and 0.7/7.35 kJ mol(-1) for Cd2+ and Ni2+ ions, respectively. Thermodynamic parameters indicated feasible and spontaneous adsorption with main participation of physisorption. Antibacterial potential of npAg deposit for water disinfection was confirmed by the moderate reduction of bacterial growth of Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, by 64%, 39%, and 70%, respectively. Thus, two synergistic effects contribute to water purification processes using Cy-npAg: pollutants removal with a simultaneous decrease of the microbial contamination contributing to overall water quality improvement.
PB  - Desalination Publ, Hopkinton
T2  - Desalination and Water Treatment
T1  - Adsorption performances and antimicrobial activity of the nanosilver modified montmorillonite clay
EP  - 369
SP  - 345
VL  - 187
DO  - 10.5004/dwt.2020.25451
ER  - 

@article{
author = "Stevanović, Maja and Bajić, Zoran J. and Veličković, Zlate and Karkalić, Radovan and Pecić, Ljiljana and Otrisal, Pavel and Marinković, Aleksandar",
year = "2020",
abstract = "The synthesis and adsorption potential of Cy-npAg, obtained by modification of raw montmorillonite clay (raw-Cy) with silver nanoparticle (npAg), was studied in this work. Optimization procedure, with respect to time, temperature and amount of deposit npAg, obtained either by reductive precipitation or ultraviolet irradiation, was performed using response surface methodology (RSM). The most efficient adsorbent, obtained by chemical reduction of silver ion with sodium borohydride, named Cy-npAg, was characterized in detail using Brunauer-Emmett-Teller, scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction techniques, and point of zero charge determination. The Cy-npAg showed good adsorption capacity with respect to non-systemic organophosphate insecticide (diazinon) as well as of heavy metals ions (Cd2+ and Ni2+ ions), that is, 74.26, 62.33, and 35.49 mg g(-1), respectively, obtained from Langmuir model fitting. Temperature dependent kinetic study allowed determination of pseudo-second rate constant (10(3) g mg(-1) min(-1))/activation energies (kJ mol(-1)): 1.45/14.48 for diazinon, and 1.27/6.59 and 0.7/7.35 kJ mol(-1) for Cd2+ and Ni2+ ions, respectively. Thermodynamic parameters indicated feasible and spontaneous adsorption with main participation of physisorption. Antibacterial potential of npAg deposit for water disinfection was confirmed by the moderate reduction of bacterial growth of Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, by 64%, 39%, and 70%, respectively. Thus, two synergistic effects contribute to water purification processes using Cy-npAg: pollutants removal with a simultaneous decrease of the microbial contamination contributing to overall water quality improvement.",
publisher = "Desalination Publ, Hopkinton",
journal = "Desalination and Water Treatment",
title = "Adsorption performances and antimicrobial activity of the nanosilver modified montmorillonite clay",
pages = "369-345",
volume = "187",
doi = "10.5004/dwt.2020.25451"
}

Stevanović, M., Bajić, Z. J., Veličković, Z., Karkalić, R., Pecić, L., Otrisal, P.,& Marinković, A.. (2020). Adsorption performances and antimicrobial activity of the nanosilver modified montmorillonite clay. in Desalination and Water Treatment
Desalination Publ, Hopkinton., 187, 345-369.
https://doi.org/10.5004/dwt.2020.25451

Stevanović M, Bajić ZJ, Veličković Z, Karkalić R, Pecić L, Otrisal P, Marinković A. Adsorption performances and antimicrobial activity of the nanosilver modified montmorillonite clay. in Desalination and Water Treatment. 2020;187:345-369.
doi:10.5004/dwt.2020.25451 .

Stevanović, Maja, Bajić, Zoran J., Veličković, Zlate, Karkalić, Radovan, Pecić, Ljiljana, Otrisal, Pavel, Marinković, Aleksandar, "Adsorption performances and antimicrobial activity of the nanosilver modified montmorillonite clay" in Desalination and Water Treatment, 187 (2020):345-369,
https://doi.org/10.5004/dwt.2020.25451 . .

TY  - CONF
AU  - Karić, Nataša
AU  - Gržetić, Jelena
AU  - Kovačević, Tihomir
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/6121
AB  - The starch oxidation involves oxidation of primary or secondary hydroxyl to carbonyl
or carboxyl groups, whereas the number of these groups indicates the level of oxidation.
Oxidized starch is used as surface sizing agent and coating binder in the paper industry,
or as polymeric filler that increases the polymer degradability. The main objective of the
presented study is to investigate the effects of various parameters on the oxidation
process of the wheat starch, using dry method (Fig. 1). These parameters include
oxidizer concentration, catalyst type (iron(II) sulphate, copper(II) sulphate and
copper(II) citrate), presence of plasticizers/modifiers (ricinoleic acid, (R-(Z))-12-
hydroxy-9-octadecenoic acid, RA) and diizopropyl tartarate ((dipropan-2-yl 2,3-
dihydroxybutanedioate, DIPT) and reaction temperature (20 and 80 °C). The obtained
results suggest that higher values of carbonyl and carboxyl groups lead to an increase of
swelling capacity and solubility, while viscosity decreases, compared to the native wheat
starch. The analysis of FTIR spectra, especially region of carbonyl/carboxyl groups
absorption, reveals high impact of process parameters on the oxidation degree and band
structure. The morphology of native and oxidized starches, investigated by the SEM
method, shows that after oxidation the surface of the starch particles becomes smoother
then for the native starch, with aggregation of small and large-sized granules.
C3  - 7th Conference of the Young Chemists of Serbia
T1  - Preparation and characterization of oxidized wheat starch with hydrogen peroxide as an environmentally friendly oxidant
SP  - 144
UR  - https://hdl.handle.net/21.15107/rcub_technorep_6121
ER  - 

@conference{
author = "Karić, Nataša and Gržetić, Jelena and Kovačević, Tihomir and Marinković, Aleksandar",
year = "2019",
abstract = "The starch oxidation involves oxidation of primary or secondary hydroxyl to carbonyl
or carboxyl groups, whereas the number of these groups indicates the level of oxidation.
Oxidized starch is used as surface sizing agent and coating binder in the paper industry,
or as polymeric filler that increases the polymer degradability. The main objective of the
presented study is to investigate the effects of various parameters on the oxidation
process of the wheat starch, using dry method (Fig. 1). These parameters include
oxidizer concentration, catalyst type (iron(II) sulphate, copper(II) sulphate and
copper(II) citrate), presence of plasticizers/modifiers (ricinoleic acid, (R-(Z))-12-
hydroxy-9-octadecenoic acid, RA) and diizopropyl tartarate ((dipropan-2-yl 2,3-
dihydroxybutanedioate, DIPT) and reaction temperature (20 and 80 °C). The obtained
results suggest that higher values of carbonyl and carboxyl groups lead to an increase of
swelling capacity and solubility, while viscosity decreases, compared to the native wheat
starch. The analysis of FTIR spectra, especially region of carbonyl/carboxyl groups
absorption, reveals high impact of process parameters on the oxidation degree and band
structure. The morphology of native and oxidized starches, investigated by the SEM
method, shows that after oxidation the surface of the starch particles becomes smoother
then for the native starch, with aggregation of small and large-sized granules.",
journal = "7th Conference of the Young Chemists of Serbia",
title = "Preparation and characterization of oxidized wheat starch with hydrogen peroxide as an environmentally friendly oxidant",
pages = "144",
url = "https://hdl.handle.net/21.15107/rcub_technorep_6121"
}

Karić, N., Gržetić, J., Kovačević, T.,& Marinković, A.. (2019). Preparation and characterization of oxidized wheat starch with hydrogen peroxide as an environmentally friendly oxidant. in 7th Conference of the Young Chemists of Serbia, 144.
https://hdl.handle.net/21.15107/rcub_technorep_6121

Karić N, Gržetić J, Kovačević T, Marinković A. Preparation and characterization of oxidized wheat starch with hydrogen peroxide as an environmentally friendly oxidant. in 7th Conference of the Young Chemists of Serbia. 2019;:144.
https://hdl.handle.net/21.15107/rcub_technorep_6121 .

Karić, Nataša, Gržetić, Jelena, Kovačević, Tihomir, Marinković, Aleksandar, "Preparation and characterization of oxidized wheat starch with hydrogen peroxide as an environmentally friendly oxidant" in 7th Conference of the Young Chemists of Serbia (2019):144,
https://hdl.handle.net/21.15107/rcub_technorep_6121 .

TY  - JOUR
AU  - Obradović, Nina
AU  - Fahrenholtz, William G.
AU  - Filipović, Suzana
AU  - Kosanović, Darko
AU  - Dapčević, Aleksandra
AU  - Đorđević, Antonije
AU  - Balać, Igor
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4264
AB  - Magnesium aluminate, MgAl2O4 and other alumina-based spinels are ceramics with high hardness, high melting point and mechanical strenght. Spinels can also be used as dielectrics in microwave applications. The goal of this study was to examine the effects of mechanical activation and sintering temperatures on physico-chemical properties of spinel. MgAl2O4 was produced by solid state reaction between MgO and alpha-Al2O3. The starting powders were mixed by ball milling to homogenize without significant particle size reduction. Mechanical activation of mixed powders was performed in a high-energy planetary ball mill in air for 1 h. Powders were compacted at 300 MPa. Heat treatments were performed in air, at temperatures ranging from 1200 to 1600 degrees C with 2 h dwell time, to determine the amount of spinel formation as a function of temperature. Phase composition and microstructure of initial powders and heated samples were determined by means of X-ray diffraction, particle size analysis, and scanning electron microscopy. The influences of milling and consolidation parameters were studied by electrical measurements and mechanical characterization. The main conclusion of this study was that mechanical activation for 60 min initiated a mechano-chemical reaction, resulted in spinel formation at much lower temperatures than within non-activated powders, and indicated that final sintering stage started at much lower temperatures for activated powders. Changes in microstructure parameters, as a consequence of mechanical treatment and subsequent heating of investigated powder mixtures, strongly affect electrical and mechanical properties of the final ceramics.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics
EP  - 12021
IS  - 9
SP  - 12015
VL  - 45
DO  - 10.1016/j.ceramint.2019.03.095
ER  - 

@article{
author = "Obradović, Nina and Fahrenholtz, William G. and Filipović, Suzana and Kosanović, Darko and Dapčević, Aleksandra and Đorđević, Antonije and Balać, Igor and Pavlović, Vladimir B.",
year = "2019",
abstract = "Magnesium aluminate, MgAl2O4 and other alumina-based spinels are ceramics with high hardness, high melting point and mechanical strenght. Spinels can also be used as dielectrics in microwave applications. The goal of this study was to examine the effects of mechanical activation and sintering temperatures on physico-chemical properties of spinel. MgAl2O4 was produced by solid state reaction between MgO and alpha-Al2O3. The starting powders were mixed by ball milling to homogenize without significant particle size reduction. Mechanical activation of mixed powders was performed in a high-energy planetary ball mill in air for 1 h. Powders were compacted at 300 MPa. Heat treatments were performed in air, at temperatures ranging from 1200 to 1600 degrees C with 2 h dwell time, to determine the amount of spinel formation as a function of temperature. Phase composition and microstructure of initial powders and heated samples were determined by means of X-ray diffraction, particle size analysis, and scanning electron microscopy. The influences of milling and consolidation parameters were studied by electrical measurements and mechanical characterization. The main conclusion of this study was that mechanical activation for 60 min initiated a mechano-chemical reaction, resulted in spinel formation at much lower temperatures than within non-activated powders, and indicated that final sintering stage started at much lower temperatures for activated powders. Changes in microstructure parameters, as a consequence of mechanical treatment and subsequent heating of investigated powder mixtures, strongly affect electrical and mechanical properties of the final ceramics.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics",
pages = "12021-12015",
number = "9",
volume = "45",
doi = "10.1016/j.ceramint.2019.03.095"
}

Obradović, N., Fahrenholtz, W. G., Filipović, S., Kosanović, D., Dapčević, A., Đorđević, A., Balać, I.,& Pavlović, V. B.. (2019). The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics. in Ceramics International
Elsevier Sci Ltd, Oxford., 45(9), 12015-12021.
https://doi.org/10.1016/j.ceramint.2019.03.095

Obradović N, Fahrenholtz WG, Filipović S, Kosanović D, Dapčević A, Đorđević A, Balać I, Pavlović VB. The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics. in Ceramics International. 2019;45(9):12015-12021.
doi:10.1016/j.ceramint.2019.03.095 .

Obradović, Nina, Fahrenholtz, William G., Filipović, Suzana, Kosanović, Darko, Dapčević, Aleksandra, Đorđević, Antonije, Balać, Igor, Pavlović, Vladimir B., "The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics" in Ceramics International, 45, no. 9 (2019):12015-12021,
https://doi.org/10.1016/j.ceramint.2019.03.095 . .

TY  - JOUR
AU  - Pantić, Krstimir
AU  - Bajić, Zoran J.
AU  - Veličković, Zlate
AU  - Nesić, Jovica Z.
AU  - Đolić, Maja
AU  - Tomić, Nataša
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4071
AB  - This batch and column kinetics study of arsenic removal utilized copper-impregnated natural mineral tufa (T-Cu(A-C)) under three ranges of particle size. Non-competitive kinetic data fitted by the Weber-Morris model and the single resistance mass transfer model, i.e., mass transfer coefficient k(f)a and diffusion coefficient (D-eff) determination, defined intra-particle diffusion as the dominating rate controlling step. Kinetic activation parameters, derived from pseudo-second-order rate constants, showed low dependence on adsorbent geometry/morphology and porosity, while the diffusivity of the pores was significant to removal efficacy. The results of competitive arsenic adsorption in a multi-component system of phosphate, chromate, or silicate showed effective arsenic removal using T-Cu adsorbents. The high adsorption rate-pseudo-second-order constants in the range 0.509-0.789gmg(-1)min(-1) for As(V) and 0.304-0.532gmg(1)min(1) for As(III)-justified further application T-Cu(A-C) in a flow system. The fixed-bed column adsorption data was fitted using empirical Bohart-Adams, Yoon-Nelson, Thomas, and dose-response models to indicate capacities and breakthrough time dependence on arsenic influent concentration and the flow rate. Pore surface diffusion modeling (PSDM), following bed-column testing, further determined adsorbent capacities and mass transport under applied hydraulic loading rates.
PB  - Springer Heidelberg, Heidelberg
T2  - Environmental Science and Pollution Research
T1  - Arsenic removal by copper-impregnated natural mineral tufa part II: a kinetics and column adsorption study
EP  - 24161
IS  - 23
SP  - 24143
VL  - 26
DO  - 10.1007/s11356-019-05547-7
ER  - 

@article{
author = "Pantić, Krstimir and Bajić, Zoran J. and Veličković, Zlate and Nesić, Jovica Z. and Đolić, Maja and Tomić, Nataša and Marinković, Aleksandar",
year = "2019",
abstract = "This batch and column kinetics study of arsenic removal utilized copper-impregnated natural mineral tufa (T-Cu(A-C)) under three ranges of particle size. Non-competitive kinetic data fitted by the Weber-Morris model and the single resistance mass transfer model, i.e., mass transfer coefficient k(f)a and diffusion coefficient (D-eff) determination, defined intra-particle diffusion as the dominating rate controlling step. Kinetic activation parameters, derived from pseudo-second-order rate constants, showed low dependence on adsorbent geometry/morphology and porosity, while the diffusivity of the pores was significant to removal efficacy. The results of competitive arsenic adsorption in a multi-component system of phosphate, chromate, or silicate showed effective arsenic removal using T-Cu adsorbents. The high adsorption rate-pseudo-second-order constants in the range 0.509-0.789gmg(-1)min(-1) for As(V) and 0.304-0.532gmg(1)min(1) for As(III)-justified further application T-Cu(A-C) in a flow system. The fixed-bed column adsorption data was fitted using empirical Bohart-Adams, Yoon-Nelson, Thomas, and dose-response models to indicate capacities and breakthrough time dependence on arsenic influent concentration and the flow rate. Pore surface diffusion modeling (PSDM), following bed-column testing, further determined adsorbent capacities and mass transport under applied hydraulic loading rates.",
publisher = "Springer Heidelberg, Heidelberg",
journal = "Environmental Science and Pollution Research",
title = "Arsenic removal by copper-impregnated natural mineral tufa part II: a kinetics and column adsorption study",
pages = "24161-24143",
number = "23",
volume = "26",
doi = "10.1007/s11356-019-05547-7"
}

Pantić, K., Bajić, Z. J., Veličković, Z., Nesić, J. Z., Đolić, M., Tomić, N.,& Marinković, A.. (2019). Arsenic removal by copper-impregnated natural mineral tufa part II: a kinetics and column adsorption study. in Environmental Science and Pollution Research
Springer Heidelberg, Heidelberg., 26(23), 24143-24161.
https://doi.org/10.1007/s11356-019-05547-7

Pantić K, Bajić ZJ, Veličković Z, Nesić JZ, Đolić M, Tomić N, Marinković A. Arsenic removal by copper-impregnated natural mineral tufa part II: a kinetics and column adsorption study. in Environmental Science and Pollution Research. 2019;26(23):24143-24161.
doi:10.1007/s11356-019-05547-7 .

Pantić, Krstimir, Bajić, Zoran J., Veličković, Zlate, Nesić, Jovica Z., Đolić, Maja, Tomić, Nataša, Marinković, Aleksandar, "Arsenic removal by copper-impregnated natural mineral tufa part II: a kinetics and column adsorption study" in Environmental Science and Pollution Research, 26, no. 23 (2019):24143-24161,
https://doi.org/10.1007/s11356-019-05547-7 . .

TY  - JOUR
AU  - Tomić, Miloš
AU  - Dunjić, Branko
AU  - Nikolić, Marija
AU  - Trifković, Kata T.
AU  - Stanković, Nadežda
AU  - Pavlović, Vladimir B.
AU  - Bajat, Jelena
AU  - Đonlagić, Jasna
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4262
AB  - In the present study the commercial multifunctional fatty acid polyamidoamine (PAA) was for the first time simultaneously applied as a curing agent and clay modifier for epoxy/clay nanocomposites (NC) based on diglycidyl ether of bisphenol A. The montmorillonite (Cloisite (R) Na+) was modified with different quantities of partially and fully protonated polyamidoamine. The NCs with 0.5 wt% novel organoclay were prepared by solution intercalation method. The major aims of this paper are investigations of the effects of the composition of PAA modified clays on structure, mechanical, barrier properties and corrosion stability on steel substrates of NCs were studied. The thermogravimetric, flame photometry and X-ray diffraction analyses confirmed the efficient modification of clay surface with polyamidoamine, predominantly located within layers. The NCs exhibited an intercalated/exfoliated morphology and the presence of free amino groups and increased content of modifier facilitated dispersion of clay particles within the polymer matrix, as shown by electron microscopy techniques (SEM, TEM). Under an optimized loading of PAA (molar quantity of total amino groups per clay cation exchange capacity of 1.75), the layers in stacks were separated by 5.0 nm and high number of individual layers was present in NC. Clay modified by PAA with free amino groups showed increased storage modulus in the rubbery state, glass transition temperature of NCs, while dumping factor was decreased. The tensile test confirmed that introduction of flexible modifier on the epoxy/clay interface lead to increase in the ultimate tensile strenght and elongation at break by 31% and toughness up to 83%. The electrochemical impedance spectroscopy and permeability tests proved the pronounced barrier effect of clay particles against corrosive species and water vapor when high dispersion degree of clay in NC was achieved.
PB  - Elsevier Science Sa, Lausanne
T2  - Progress in Organic Coatings
T1  - Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites
EP  - 321
SP  - 311
VL  - 131
DO  - 10.1016/j.porgcoat.2019.02.037
ER  - 

@article{
author = "Tomić, Miloš and Dunjić, Branko and Nikolić, Marija and Trifković, Kata T. and Stanković, Nadežda and Pavlović, Vladimir B. and Bajat, Jelena and Đonlagić, Jasna",
year = "2019",
abstract = "In the present study the commercial multifunctional fatty acid polyamidoamine (PAA) was for the first time simultaneously applied as a curing agent and clay modifier for epoxy/clay nanocomposites (NC) based on diglycidyl ether of bisphenol A. The montmorillonite (Cloisite (R) Na+) was modified with different quantities of partially and fully protonated polyamidoamine. The NCs with 0.5 wt% novel organoclay were prepared by solution intercalation method. The major aims of this paper are investigations of the effects of the composition of PAA modified clays on structure, mechanical, barrier properties and corrosion stability on steel substrates of NCs were studied. The thermogravimetric, flame photometry and X-ray diffraction analyses confirmed the efficient modification of clay surface with polyamidoamine, predominantly located within layers. The NCs exhibited an intercalated/exfoliated morphology and the presence of free amino groups and increased content of modifier facilitated dispersion of clay particles within the polymer matrix, as shown by electron microscopy techniques (SEM, TEM). Under an optimized loading of PAA (molar quantity of total amino groups per clay cation exchange capacity of 1.75), the layers in stacks were separated by 5.0 nm and high number of individual layers was present in NC. Clay modified by PAA with free amino groups showed increased storage modulus in the rubbery state, glass transition temperature of NCs, while dumping factor was decreased. The tensile test confirmed that introduction of flexible modifier on the epoxy/clay interface lead to increase in the ultimate tensile strenght and elongation at break by 31% and toughness up to 83%. The electrochemical impedance spectroscopy and permeability tests proved the pronounced barrier effect of clay particles against corrosive species and water vapor when high dispersion degree of clay in NC was achieved.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Progress in Organic Coatings",
title = "Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites",
pages = "321-311",
volume = "131",
doi = "10.1016/j.porgcoat.2019.02.037"
}

Tomić, M., Dunjić, B., Nikolić, M., Trifković, K. T., Stanković, N., Pavlović, V. B., Bajat, J.,& Đonlagić, J.. (2019). Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites. in Progress in Organic Coatings
Elsevier Science Sa, Lausanne., 131, 311-321.
https://doi.org/10.1016/j.porgcoat.2019.02.037

Tomić M, Dunjić B, Nikolić M, Trifković KT, Stanković N, Pavlović VB, Bajat J, Đonlagić J. Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites. in Progress in Organic Coatings. 2019;131:311-321.
doi:10.1016/j.porgcoat.2019.02.037 .

Tomić, Miloš, Dunjić, Branko, Nikolić, Marija, Trifković, Kata T., Stanković, Nadežda, Pavlović, Vladimir B., Bajat, Jelena, Đonlagić, Jasna, "Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites" in Progress in Organic Coatings, 131 (2019):311-321,
https://doi.org/10.1016/j.porgcoat.2019.02.037 . .

TY  - JOUR
AU  - Mijatović, Nevenka
AU  - Terzić, Anja
AU  - Pezo, Lato
AU  - Milicić, Ljiljana
AU  - Živojinović, Dragana
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4097
AB  - Adjustment and subsequent validation of energy-dispersive X-ray fluorescence (ED-XRF) method for cement based binders with addition of mineral raw materials (fly ash, zeolite and bentonite) was conducted. Eighteen chemical elements present in the material composition were analyzed: ten major elements (Si, Al, Fe, Ca, Mg, S, Na, K, Ti, P) and eight trace elements (Cr, Zn, Cu, As, Ni, Pb, Sr, Mn). Thirty-five samples of either certified reference materials or reference materials of cement, fly ash and clay were utilized during adjustment and optimization of the investigated ED-XRF procedure. The method was consecutively validated in terms of selectivity, precision, working range, linearity, accuracy, robustness, limits of detection and quantification. Thirty-two samples in total, i.e. three certified reference materials and twenty-nine reference materials, were simultaneously analyzed by ED-XRF and inductively coupled plasma optical emission spectrometry (ICP-OES). Comparison of the outputs of monitored methods showed infinitesimally small differences, as correlation coefficients were extremely good (approximate to 1), which highlighted ED-XRF as highly satiable alternative for ICP-OES for the chemical analysis of cement binders.
PB  - Pergamon-Elsevier Science Ltd, Oxford
T2  - Spectrochimica Acta Part B-Atomic Spectroscopy
T1  - Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites
SP  - 105729
VL  - 162
DO  - 10.1016/j.sab.2019.105729
ER  - 

@article{
author = "Mijatović, Nevenka and Terzić, Anja and Pezo, Lato and Milicić, Ljiljana and Živojinović, Dragana",
year = "2019",
abstract = "Adjustment and subsequent validation of energy-dispersive X-ray fluorescence (ED-XRF) method for cement based binders with addition of mineral raw materials (fly ash, zeolite and bentonite) was conducted. Eighteen chemical elements present in the material composition were analyzed: ten major elements (Si, Al, Fe, Ca, Mg, S, Na, K, Ti, P) and eight trace elements (Cr, Zn, Cu, As, Ni, Pb, Sr, Mn). Thirty-five samples of either certified reference materials or reference materials of cement, fly ash and clay were utilized during adjustment and optimization of the investigated ED-XRF procedure. The method was consecutively validated in terms of selectivity, precision, working range, linearity, accuracy, robustness, limits of detection and quantification. Thirty-two samples in total, i.e. three certified reference materials and twenty-nine reference materials, were simultaneously analyzed by ED-XRF and inductively coupled plasma optical emission spectrometry (ICP-OES). Comparison of the outputs of monitored methods showed infinitesimally small differences, as correlation coefficients were extremely good (approximate to 1), which highlighted ED-XRF as highly satiable alternative for ICP-OES for the chemical analysis of cement binders.",
publisher = "Pergamon-Elsevier Science Ltd, Oxford",
journal = "Spectrochimica Acta Part B-Atomic Spectroscopy",
title = "Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites",
pages = "105729",
volume = "162",
doi = "10.1016/j.sab.2019.105729"
}

Mijatović, N., Terzić, A., Pezo, L., Milicić, L.,& Živojinović, D.. (2019). Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites. in Spectrochimica Acta Part B-Atomic Spectroscopy
Pergamon-Elsevier Science Ltd, Oxford., 162, 105729.
https://doi.org/10.1016/j.sab.2019.105729

Mijatović N, Terzić A, Pezo L, Milicić L, Živojinović D. Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites. in Spectrochimica Acta Part B-Atomic Spectroscopy. 2019;162:105729.
doi:10.1016/j.sab.2019.105729 .

Mijatović, Nevenka, Terzić, Anja, Pezo, Lato, Milicić, Ljiljana, Živojinović, Dragana, "Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites" in Spectrochimica Acta Part B-Atomic Spectroscopy, 162 (2019):105729,
https://doi.org/10.1016/j.sab.2019.105729 . .

TY  - JOUR
AU  - Mijatović, Nevenka
AU  - Terzić, Anja
AU  - Pezo, Lato
AU  - Milicić, Ljiljana
AU  - Milosavljević, Aleksandra
AU  - Živojinović, Dragana
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4137
AB  - New global tendencies for waste materials reusing in building materials are imposing the request for improved performances of chemical analysis methods and the improvements of matrices used. A new method for optical emission spectrometry with inductively coupled plasma (ICP-OES) is developed and validated for the chemical analysis (35 elements: Al, Be, Cd, So, Cr, Cu, Fe, Mn, Mo, Ni, V, Mo, Zn, Pb , Bi, Si, Zr, W, As, Se, Sb, Sn, Ti, Ba, B, Ag, Mg, Ca, K, Na, S, P, Ga, In, Li) in leachate of fly ash. Validation performances and the uncertainty of measurement were resolved. Uncertainty of measurements were resolved by three routes: validation procedure, participation in proficiency testing (PT) schemes and standard method. The obtained method is a new simple and effective analyzing route for determination of undesired trace elements and their quantity comprised in leachates of fly ash, and leachates of building materials with addition of fly ash (cement binders and mortars). In order to prove its accuracy and precision, the developed method was employed on laboratory samples of cement binders and mortars. Results were compared with limit values provided in the standard. Multivariate analyses, i.e. cluster analysis and principal component analysis, were applied to establish interrelations between analyzed samples, and to certify the developed ICP-OES method.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition
EP  - 444
IS  - 4
SP  - 429
VL  - 51
DO  - 10.2298/SOS1904429M
ER  - 

@article{
author = "Mijatović, Nevenka and Terzić, Anja and Pezo, Lato and Milicić, Ljiljana and Milosavljević, Aleksandra and Živojinović, Dragana",
year = "2019",
abstract = "New global tendencies for waste materials reusing in building materials are imposing the request for improved performances of chemical analysis methods and the improvements of matrices used. A new method for optical emission spectrometry with inductively coupled plasma (ICP-OES) is developed and validated for the chemical analysis (35 elements: Al, Be, Cd, So, Cr, Cu, Fe, Mn, Mo, Ni, V, Mo, Zn, Pb , Bi, Si, Zr, W, As, Se, Sb, Sn, Ti, Ba, B, Ag, Mg, Ca, K, Na, S, P, Ga, In, Li) in leachate of fly ash. Validation performances and the uncertainty of measurement were resolved. Uncertainty of measurements were resolved by three routes: validation procedure, participation in proficiency testing (PT) schemes and standard method. The obtained method is a new simple and effective analyzing route for determination of undesired trace elements and their quantity comprised in leachates of fly ash, and leachates of building materials with addition of fly ash (cement binders and mortars). In order to prove its accuracy and precision, the developed method was employed on laboratory samples of cement binders and mortars. Results were compared with limit values provided in the standard. Multivariate analyses, i.e. cluster analysis and principal component analysis, were applied to establish interrelations between analyzed samples, and to certify the developed ICP-OES method.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition",
pages = "444-429",
number = "4",
volume = "51",
doi = "10.2298/SOS1904429M"
}

Mijatović, N., Terzić, A., Pezo, L., Milicić, L., Milosavljević, A.,& Živojinović, D.. (2019). Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 51(4), 429-444.
https://doi.org/10.2298/SOS1904429M

Mijatović N, Terzić A, Pezo L, Milicić L, Milosavljević A, Živojinović D. Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition. in Science of Sintering. 2019;51(4):429-444.
doi:10.2298/SOS1904429M .

Mijatović, Nevenka, Terzić, Anja, Pezo, Lato, Milicić, Ljiljana, Milosavljević, Aleksandra, Živojinović, Dragana, "Novel Approach for Determination of Potentially Toxic Elements via ICP-OES in Aqueous Solutions of Building Materials with Industrial Byproduct Addition" in Science of Sintering, 51, no. 4 (2019):429-444,
https://doi.org/10.2298/SOS1904429M . .

TY  - JOUR
AU  - Mijatović, Nevenka
AU  - Terzić, Anja
AU  - Pezo, Lato
AU  - Milicić, Ljiljana
AU  - Živojinović, Dragana
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/5039
AB  - Adjustment and subsequent validation of energy-dispersive X-ray fluorescence (ED-XRF) method for cement based binders with addition of mineral raw materials (fly ash, zeolite and bentonite) was conducted. Eighteen chemical elements present in the material composition were analyzed: ten major elements (Si, Al, Fe, Ca, Mg, S, Na, K, Ti, P) and eight trace elements (Cr, Zn, Cu, As, Ni, Pb, Sr, Mn). Thirty-five samples of either certified reference materials or reference materials of cement, fly ash and clay were utilized during adjustment and optimization of the investigated ED-XRF procedure. The method was consecutively validated in terms of selectivity, precision, working range, linearity, accuracy, robustness, limits of detection and quantification. Thirty-two samples in total, i.e. three certified reference materials and twenty-nine reference materials, were simultaneously analyzed by ED-XRF and inductively coupled plasma optical emission spectrometry (ICP-OES). Comparison of the outputs of monitored methods showed infinitesimally small differences, as correlation coefficients were extremely good (≈1), which highlighted ED-XRF as highly satiable alternative for ICP-OES for the chemical analysis of cement binders.
PB  - Elsevier B.V.
T2  - Spectrochimica Acta - Part B Atomic Spectroscopy
T1  - Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites
SP  - 105729
VL  - 162
DO  - 10.1016/j.sab.2019.105729
ER  - 

@article{
author = "Mijatović, Nevenka and Terzić, Anja and Pezo, Lato and Milicić, Ljiljana and Živojinović, Dragana",
year = "2019",
abstract = "Adjustment and subsequent validation of energy-dispersive X-ray fluorescence (ED-XRF) method for cement based binders with addition of mineral raw materials (fly ash, zeolite and bentonite) was conducted. Eighteen chemical elements present in the material composition were analyzed: ten major elements (Si, Al, Fe, Ca, Mg, S, Na, K, Ti, P) and eight trace elements (Cr, Zn, Cu, As, Ni, Pb, Sr, Mn). Thirty-five samples of either certified reference materials or reference materials of cement, fly ash and clay were utilized during adjustment and optimization of the investigated ED-XRF procedure. The method was consecutively validated in terms of selectivity, precision, working range, linearity, accuracy, robustness, limits of detection and quantification. Thirty-two samples in total, i.e. three certified reference materials and twenty-nine reference materials, were simultaneously analyzed by ED-XRF and inductively coupled plasma optical emission spectrometry (ICP-OES). Comparison of the outputs of monitored methods showed infinitesimally small differences, as correlation coefficients were extremely good (≈1), which highlighted ED-XRF as highly satiable alternative for ICP-OES for the chemical analysis of cement binders.",
publisher = "Elsevier B.V.",
journal = "Spectrochimica Acta - Part B Atomic Spectroscopy",
title = "Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites",
pages = "105729",
volume = "162",
doi = "10.1016/j.sab.2019.105729"
}

Mijatović, N., Terzić, A., Pezo, L., Milicić, L.,& Živojinović, D.. (2019). Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites. in Spectrochimica Acta - Part B Atomic Spectroscopy
Elsevier B.V.., 162, 105729.
https://doi.org/10.1016/j.sab.2019.105729

Mijatović N, Terzić A, Pezo L, Milicić L, Živojinović D. Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites. in Spectrochimica Acta - Part B Atomic Spectroscopy. 2019;162:105729.
doi:10.1016/j.sab.2019.105729 .

Mijatović, Nevenka, Terzić, Anja, Pezo, Lato, Milicić, Ljiljana, Živojinović, Dragana, "Validation of energy-dispersive X-ray fluorescence procedure for determination of major and trace elements present in the cement based composites" in Spectrochimica Acta - Part B Atomic Spectroscopy, 162 (2019):105729,
https://doi.org/10.1016/j.sab.2019.105729 . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Fahrenholtz, William G.
AU  - Filipović, Suzana
AU  - Corlett, Cole
AU  - Đorđević, Pavle
AU  - Rogan, Jelena
AU  - Vulić, Predrag
AU  - Buljak, Vladimir
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4136
AB  - Single phase MgAl2O4 was made from a one-to-one molar ratio of MgO and Al2O3 powders mixed using ball-milling. Mixtures of MgO and Al2O3 were subsequently treated in planetary ball mill for 30, 60, 90 and 120 minutes in air. The aim of this study was to examine phase composition, microstructure, and densification behavior of sintered specimens. After sintering in dilatometer at 1500 degrees C, the powder was converted to single phase MgAl2O4. The results show that mechanical activation improved the densification behavior of MgAl2O4 sintered specimens, and it reduced the onset temperature for sintering by approx. 100 degrees C. Based on dilatometer data, powders were subsequently densified at 1450 degrees C by hot pressing. Almost all specimens exhibited full density, while sample activated for 30 minutes showed the fastest densification rate.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Characterization of MgAl2O4 Sintered Ceramics
EP  - 376
IS  - 4
SP  - 363
VL  - 51
DO  - 10.2298/SOS1904363O
ER  - 

@article{
author = "Obradović, Nina and Fahrenholtz, William G. and Filipović, Suzana and Corlett, Cole and Đorđević, Pavle and Rogan, Jelena and Vulić, Predrag and Buljak, Vladimir and Pavlović, Vladimir B.",
year = "2019",
abstract = "Single phase MgAl2O4 was made from a one-to-one molar ratio of MgO and Al2O3 powders mixed using ball-milling. Mixtures of MgO and Al2O3 were subsequently treated in planetary ball mill for 30, 60, 90 and 120 minutes in air. The aim of this study was to examine phase composition, microstructure, and densification behavior of sintered specimens. After sintering in dilatometer at 1500 degrees C, the powder was converted to single phase MgAl2O4. The results show that mechanical activation improved the densification behavior of MgAl2O4 sintered specimens, and it reduced the onset temperature for sintering by approx. 100 degrees C. Based on dilatometer data, powders were subsequently densified at 1450 degrees C by hot pressing. Almost all specimens exhibited full density, while sample activated for 30 minutes showed the fastest densification rate.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Characterization of MgAl2O4 Sintered Ceramics",
pages = "376-363",
number = "4",
volume = "51",
doi = "10.2298/SOS1904363O"
}

Obradović, N., Fahrenholtz, W. G., Filipović, S., Corlett, C., Đorđević, P., Rogan, J., Vulić, P., Buljak, V.,& Pavlović, V. B.. (2019). Characterization of MgAl2O4 Sintered Ceramics. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 51(4), 363-376.
https://doi.org/10.2298/SOS1904363O

Obradović N, Fahrenholtz WG, Filipović S, Corlett C, Đorđević P, Rogan J, Vulić P, Buljak V, Pavlović VB. Characterization of MgAl2O4 Sintered Ceramics. in Science of Sintering. 2019;51(4):363-376.
doi:10.2298/SOS1904363O .

Obradović, Nina, Fahrenholtz, William G., Filipović, Suzana, Corlett, Cole, Đorđević, Pavle, Rogan, Jelena, Vulić, Predrag, Buljak, Vladimir, Pavlović, Vladimir B., "Characterization of MgAl2O4 Sintered Ceramics" in Science of Sintering, 51, no. 4 (2019):363-376,
https://doi.org/10.2298/SOS1904363O . .

TY  - JOUR
AU  - Pantić, Krstimir
AU  - Bajić, Zoran J.
AU  - Veličković, Zlate
AU  - Đokić, Veljko
AU  - Rusmirović, Jelena
AU  - Marinković, Aleksandar
AU  - Perić-Grujić, Aleksandra
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4108
AB  - Synthesis of branched aminated waste polyacrylonitrile (PAN) fibers, realized in a three addition/amidation successive steps, was performed in order to obtain AS3-PAN adsorbent. Influence of various operating parameters such as pH, contact time, adsorbent mass and initial concentration of pollutants, on adsorption capacity has been studied. Design of the experimental plan of adsorption experiments, defined by response surface methodology (RSM), rationalized the number of necessary experiments. The calculated adsorption capacities for AS3-PAN, obtained by Langmuir model, were 58.94, 41.07, 34.51, 24.54 and 29.61 mg g(-1) for Pb2+, Cd2+, Ni2+, Cr(VI) and As(V) ion, respectively. The results of pseudo-second-order reaction rate and Weber-Morris kinetic model indicated significant resistance due to intra-particle (pore) diffusion. The experimental results were compared with the theoretically calculated ones, obtained by RSM prediction model, and validation of applied methodology was performed by testing the quality of the regression analysis with analysis of variance test.
PB  - Desalination Publ, Hopkinton
T2  - Desalination and Water Treatment
T1  - Adsorption performances of branched aminated waste polyacrylonitrile fibers: experimental versus modelling study
EP  - 249
SP  - 223
VL  - 171
DO  - 10.5004/dwt.2019.24758
ER  - 

@article{
author = "Pantić, Krstimir and Bajić, Zoran J. and Veličković, Zlate and Đokić, Veljko and Rusmirović, Jelena and Marinković, Aleksandar and Perić-Grujić, Aleksandra",
year = "2019",
abstract = "Synthesis of branched aminated waste polyacrylonitrile (PAN) fibers, realized in a three addition/amidation successive steps, was performed in order to obtain AS3-PAN adsorbent. Influence of various operating parameters such as pH, contact time, adsorbent mass and initial concentration of pollutants, on adsorption capacity has been studied. Design of the experimental plan of adsorption experiments, defined by response surface methodology (RSM), rationalized the number of necessary experiments. The calculated adsorption capacities for AS3-PAN, obtained by Langmuir model, were 58.94, 41.07, 34.51, 24.54 and 29.61 mg g(-1) for Pb2+, Cd2+, Ni2+, Cr(VI) and As(V) ion, respectively. The results of pseudo-second-order reaction rate and Weber-Morris kinetic model indicated significant resistance due to intra-particle (pore) diffusion. The experimental results were compared with the theoretically calculated ones, obtained by RSM prediction model, and validation of applied methodology was performed by testing the quality of the regression analysis with analysis of variance test.",
publisher = "Desalination Publ, Hopkinton",
journal = "Desalination and Water Treatment",
title = "Adsorption performances of branched aminated waste polyacrylonitrile fibers: experimental versus modelling study",
pages = "249-223",
volume = "171",
doi = "10.5004/dwt.2019.24758"
}

Pantić, K., Bajić, Z. J., Veličković, Z., Đokić, V., Rusmirović, J., Marinković, A.,& Perić-Grujić, A.. (2019). Adsorption performances of branched aminated waste polyacrylonitrile fibers: experimental versus modelling study. in Desalination and Water Treatment
Desalination Publ, Hopkinton., 171, 223-249.
https://doi.org/10.5004/dwt.2019.24758

Pantić K, Bajić ZJ, Veličković Z, Đokić V, Rusmirović J, Marinković A, Perić-Grujić A. Adsorption performances of branched aminated waste polyacrylonitrile fibers: experimental versus modelling study. in Desalination and Water Treatment. 2019;171:223-249.
doi:10.5004/dwt.2019.24758 .

Pantić, Krstimir, Bajić, Zoran J., Veličković, Zlate, Đokić, Veljko, Rusmirović, Jelena, Marinković, Aleksandar, Perić-Grujić, Aleksandra, "Adsorption performances of branched aminated waste polyacrylonitrile fibers: experimental versus modelling study" in Desalination and Water Treatment, 171 (2019):223-249,
https://doi.org/10.5004/dwt.2019.24758 . .

TY  - JOUR
AU  - Vujančević, Jelena
AU  - Andričević, Pavao
AU  - Bjelajac, Anđelika
AU  - Đokić, Veljko
AU  - Popović, Maja
AU  - Rakočević, Zlatko Lj.
AU  - Horvath, Endre
AU  - Kollar, Marton
AU  - Nafradi, Balint
AU  - Schiller, Andreas
AU  - Domanski, Konrad
AU  - Forro, Laszlo
AU  - Pavlović, Vera P.
AU  - Janaćković, Đorđe
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4251
AB  - Highly ordered, anodically grown TiO2 nanotubes on titanium supports were annealed in ammonia atmosphere in order to incorporate nitrogen doping ( lt = 2 at.%) in the titanium oxide lattice. FESEM micrographs revealed nanotubes with an average outer diameter of 101.5 +/- 1.5 nm and an average wall thickness of about 13 nm. Anatase crystals were formed inside the tubes after annealing in ammonia atmosphere for 30 min. With further annealing, rutile peaks appeared due to the thermal oxidation of the foil and rise as the duration of heat treatment was increased. The concentration and chemical nature of nitrogen in the nanotube arrays can be correlated to the optical response of dry-pressed heterojunctions of doped TiO2/CH3NH3PbI3 single crystals. The N-TiO2/perovskite heterojunction with the highest amount of interstitial nitrogen exhibited an improved photocurrent, indicating the importance of the semiconductor doping-based heterojunction optimization strategies to deliver competitive levels of halide perovskite-based optoelectronic devices to be envisioned for urban infrastructures.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping
EP  - 10020
IS  - 8
SP  - 10013
VL  - 45
DO  - 10.1016/j.ceramint.2019.02.045
ER  - 

@article{
author = "Vujančević, Jelena and Andričević, Pavao and Bjelajac, Anđelika and Đokić, Veljko and Popović, Maja and Rakočević, Zlatko Lj. and Horvath, Endre and Kollar, Marton and Nafradi, Balint and Schiller, Andreas and Domanski, Konrad and Forro, Laszlo and Pavlović, Vera P. and Janaćković, Đorđe",
year = "2019",
abstract = "Highly ordered, anodically grown TiO2 nanotubes on titanium supports were annealed in ammonia atmosphere in order to incorporate nitrogen doping ( lt = 2 at.%) in the titanium oxide lattice. FESEM micrographs revealed nanotubes with an average outer diameter of 101.5 +/- 1.5 nm and an average wall thickness of about 13 nm. Anatase crystals were formed inside the tubes after annealing in ammonia atmosphere for 30 min. With further annealing, rutile peaks appeared due to the thermal oxidation of the foil and rise as the duration of heat treatment was increased. The concentration and chemical nature of nitrogen in the nanotube arrays can be correlated to the optical response of dry-pressed heterojunctions of doped TiO2/CH3NH3PbI3 single crystals. The N-TiO2/perovskite heterojunction with the highest amount of interstitial nitrogen exhibited an improved photocurrent, indicating the importance of the semiconductor doping-based heterojunction optimization strategies to deliver competitive levels of halide perovskite-based optoelectronic devices to be envisioned for urban infrastructures.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping",
pages = "10020-10013",
number = "8",
volume = "45",
doi = "10.1016/j.ceramint.2019.02.045"
}

Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z. Lj., Horvath, E., Kollar, M., Nafradi, B., Schiller, A., Domanski, K., Forro, L., Pavlović, V. P.,& Janaćković, Đ.. (2019). Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. in Ceramics International
Elsevier Sci Ltd, Oxford., 45(8), 10013-10020.
https://doi.org/10.1016/j.ceramint.2019.02.045

Vujančević J, Andričević P, Bjelajac A, Đokić V, Popović M, Rakočević ZL, Horvath E, Kollar M, Nafradi B, Schiller A, Domanski K, Forro L, Pavlović VP, Janaćković Đ. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. in Ceramics International. 2019;45(8):10013-10020.
doi:10.1016/j.ceramint.2019.02.045 .

Vujančević, Jelena, Andričević, Pavao, Bjelajac, Anđelika, Đokić, Veljko, Popović, Maja, Rakočević, Zlatko Lj., Horvath, Endre, Kollar, Marton, Nafradi, Balint, Schiller, Andreas, Domanski, Konrad, Forro, Laszlo, Pavlović, Vera P., Janaćković, Đorđe, "Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping" in Ceramics International, 45, no. 8 (2019):10013-10020,
https://doi.org/10.1016/j.ceramint.2019.02.045 . .

TY  - DATA
AU  - Vujančević, Jelena
AU  - Andričević, Pavao
AU  - Bjelajac, Anđelika
AU  - Đokić, Veljko
AU  - Popović, Maja
AU  - Rakočević, Zlatko Lj.
AU  - Horváth, Endre
AU  - Kollar, Marton
AU  - Náfrádi, Bálint
AU  - Schiller, Andreas
AU  - Domanski, Konrad
AU  - Forró, Laszlo
AU  - Pavlović, Vera P.
AU  - Janaćković, Đorđe
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4163
AB  - Table S1. Reported methods for nitrogen doping of anodized TiO2 nanotube arrays; Figure S1. SEM images and statistical distributions of outer diameters obtained by analyzing SEM micrographs of 100 nanotubes; Table S2. Average morphology parameters for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Table S3. Average crystals size for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Figure S2. Deconvoluted XPS spectra of N 1s core level of Ti foil (black line-experimental, grey line-background, magenta line-envelope); Table S4. Peak positions and atomic percentages of N1s core levels for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Table S5. Positions and atomic percentages of Ti 2p3/2 and O1s core peaks for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Figure S3. The time evolution of the current during the preconditioning of the TiO2/perovskite sample at a bias voltage of 100 V for 75 sec. Dashed line is the logarithmic fit of the base line of the current time evolution; Figure S4. Ideality factor for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples
T2  - Ceramics International
T1  - Supporting information for the article: Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z., Horváth, E., Kollár, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V., Janaćković, Đ., 2019. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. Ceramics International 45, 10013–10020. https://doi.org/10.1016/j.ceramint.2019.02.045
UR  - https://hdl.handle.net/21.15107/rcub_dais_5969
ER  - 

@misc{
author = "Vujančević, Jelena and Andričević, Pavao and Bjelajac, Anđelika and Đokić, Veljko and Popović, Maja and Rakočević, Zlatko Lj. and Horváth, Endre and Kollar, Marton and Náfrádi, Bálint and Schiller, Andreas and Domanski, Konrad and Forró, Laszlo and Pavlović, Vera P. and Janaćković, Đorđe",
year = "2019",
abstract = "Table S1. Reported methods for nitrogen doping of anodized TiO2 nanotube arrays; Figure S1. SEM images and statistical distributions of outer diameters obtained by analyzing SEM micrographs of 100 nanotubes; Table S2. Average morphology parameters for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Table S3. Average crystals size for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Figure S2. Deconvoluted XPS spectra of N 1s core level of Ti foil (black line-experimental, grey line-background, magenta line-envelope); Table S4. Peak positions and atomic percentages of N1s core levels for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Table S5. Positions and atomic percentages of Ti 2p3/2 and O1s core peaks for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples; Figure S3. The time evolution of the current during the preconditioning of the TiO2/perovskite sample at a bias voltage of 100 V for 75 sec. Dashed line is the logarithmic fit of the base line of the current time evolution; Figure S4. Ideality factor for TiO2-undoped, TiO2-N30, TiO2-N60 and TiO2-N90 samples",
journal = "Ceramics International",
title = "Supporting information for the article: Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z., Horváth, E., Kollár, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V., Janaćković, Đ., 2019. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. Ceramics International 45, 10013–10020. https://doi.org/10.1016/j.ceramint.2019.02.045",
url = "https://hdl.handle.net/21.15107/rcub_dais_5969"
}

Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z. Lj., Horváth, E., Kollar, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V. P.,& Janaćković, Đ.. (2019). Supporting information for the article: Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z., Horváth, E., Kollár, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V., Janaćković, Đ., 2019. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. Ceramics International 45, 10013–10020. https://doi.org/10.1016/j.ceramint.2019.02.045. in Ceramics International.
https://hdl.handle.net/21.15107/rcub_dais_5969

Vujančević J, Andričević P, Bjelajac A, Đokić V, Popović M, Rakočević ZL, Horváth E, Kollar M, Náfrádi B, Schiller A, Domanski K, Forró L, Pavlović VP, Janaćković Đ. Supporting information for the article: Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z., Horváth, E., Kollár, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V., Janaćković, Đ., 2019. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. Ceramics International 45, 10013–10020. https://doi.org/10.1016/j.ceramint.2019.02.045. in Ceramics International. 2019;.
https://hdl.handle.net/21.15107/rcub_dais_5969 .

Vujančević, Jelena, Andričević, Pavao, Bjelajac, Anđelika, Đokić, Veljko, Popović, Maja, Rakočević, Zlatko Lj., Horváth, Endre, Kollar, Marton, Náfrádi, Bálint, Schiller, Andreas, Domanski, Konrad, Forró, Laszlo, Pavlović, Vera P., Janaćković, Đorđe, "Supporting information for the article: Vujančević, J., Andričević, P., Bjelajac, A., Đokić, V., Popović, M., Rakočević, Z., Horváth, E., Kollár, M., Náfrádi, B., Schiller, A., Domanski, K., Forró, L., Pavlović, V., Janaćković, Đ., 2019. Dry-pressed anodized titania nanotube/CH3NH3PbI3 single crystal heterojunctions: The beneficial role of N doping. Ceramics International 45, 10013–10020. https://doi.org/10.1016/j.ceramint.2019.02.045" in Ceramics International (2019),
https://hdl.handle.net/21.15107/rcub_dais_5969 .

TY  - JOUR
AU  - Taleb, Khaled
AU  - Markovski, Jasmina
AU  - Veličković, Zlate
AU  - Rusmirović, Jelena
AU  - Rančić, Milica
AU  - Pavlović, Vladimir B.
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4140
AB  - Comparative adsorption study related to benefits of parent media size, i.e. microfibrillated cellulose (MC) versus nanocellulose (NC) support, for the preparation of magnetite (MG) based high performance adsorbent for arsenic removal was conducted. Precipitation of MG on amino terminal branched organic structure, L, either linked by maleic acid residue on NC surface (NC-MA/L) or linked by oxalyl bridge on MC surface (MC-O/L) produced NC-MA/L-MG and MC-O/L-MG adsorbents, respectively. Precipitation of nanosized MG on amino functionalized NC-MA/L and MC-O/L, performed according to optimized procedure, contributed to improved textural properties and adsorptive/kinetic performances of novel adsorbents. Adsorption capacity of arsenate, As(V), was in favor of NC-MA/L-MG (85.3 versus 18.5 mg g(-1)) while MC-O/L-MG exhibited faster kinetics (0.541 versus 0.189 g mg(-1) min(-1)). Lower capacity of arsenite, As(III), removal, 68.3 mg g(-1) for NC-MA/L-MG and 17.8 mg g(-1) for MC-O/L-MG, were obtained. Calculated activation energies, 13.28 and 10.87 kJ mol(-1) for NC-MA/L-MG and MC-O/L-MG with respect to As(V), respectively, suggest, in accordance with results of Weber-Morris fitting, that internal mass transfer controls adsorption process. Model free adsorption kinetics confirmed beneficial uses of MC-O/L-MG due to low activation energy dependence on the extent of adsorption.
PB  - Elsevier, Amsterdam
T2  - Arabian Journal of Chemistry
T1  - Arsenic removal by magnetite-loaded amino modified nano/microcellulose adsorbents: Effect of functionalization and media size
EP  - 4693
IS  - 8
SP  - 4675
VL  - 12
DO  - 10.1016/j.arabjc.2016.08.006
ER  - 

@article{
author = "Taleb, Khaled and Markovski, Jasmina and Veličković, Zlate and Rusmirović, Jelena and Rančić, Milica and Pavlović, Vladimir B. and Marinković, Aleksandar",
year = "2019",
abstract = "Comparative adsorption study related to benefits of parent media size, i.e. microfibrillated cellulose (MC) versus nanocellulose (NC) support, for the preparation of magnetite (MG) based high performance adsorbent for arsenic removal was conducted. Precipitation of MG on amino terminal branched organic structure, L, either linked by maleic acid residue on NC surface (NC-MA/L) or linked by oxalyl bridge on MC surface (MC-O/L) produced NC-MA/L-MG and MC-O/L-MG adsorbents, respectively. Precipitation of nanosized MG on amino functionalized NC-MA/L and MC-O/L, performed according to optimized procedure, contributed to improved textural properties and adsorptive/kinetic performances of novel adsorbents. Adsorption capacity of arsenate, As(V), was in favor of NC-MA/L-MG (85.3 versus 18.5 mg g(-1)) while MC-O/L-MG exhibited faster kinetics (0.541 versus 0.189 g mg(-1) min(-1)). Lower capacity of arsenite, As(III), removal, 68.3 mg g(-1) for NC-MA/L-MG and 17.8 mg g(-1) for MC-O/L-MG, were obtained. Calculated activation energies, 13.28 and 10.87 kJ mol(-1) for NC-MA/L-MG and MC-O/L-MG with respect to As(V), respectively, suggest, in accordance with results of Weber-Morris fitting, that internal mass transfer controls adsorption process. Model free adsorption kinetics confirmed beneficial uses of MC-O/L-MG due to low activation energy dependence on the extent of adsorption.",
publisher = "Elsevier, Amsterdam",
journal = "Arabian Journal of Chemistry",
title = "Arsenic removal by magnetite-loaded amino modified nano/microcellulose adsorbents: Effect of functionalization and media size",
pages = "4693-4675",
number = "8",
volume = "12",
doi = "10.1016/j.arabjc.2016.08.006"
}

Taleb, K., Markovski, J., Veličković, Z., Rusmirović, J., Rančić, M., Pavlović, V. B.,& Marinković, A.. (2019). Arsenic removal by magnetite-loaded amino modified nano/microcellulose adsorbents: Effect of functionalization and media size. in Arabian Journal of Chemistry
Elsevier, Amsterdam., 12(8), 4675-4693.
https://doi.org/10.1016/j.arabjc.2016.08.006

Taleb K, Markovski J, Veličković Z, Rusmirović J, Rančić M, Pavlović VB, Marinković A. Arsenic removal by magnetite-loaded amino modified nano/microcellulose adsorbents: Effect of functionalization and media size. in Arabian Journal of Chemistry. 2019;12(8):4675-4693.
doi:10.1016/j.arabjc.2016.08.006 .

Taleb, Khaled, Markovski, Jasmina, Veličković, Zlate, Rusmirović, Jelena, Rančić, Milica, Pavlović, Vladimir B., Marinković, Aleksandar, "Arsenic removal by magnetite-loaded amino modified nano/microcellulose adsorbents: Effect of functionalization and media size" in Arabian Journal of Chemistry, 12, no. 8 (2019):4675-4693,
https://doi.org/10.1016/j.arabjc.2016.08.006 . .

TY  - JOUR
AU  - Drah, Abdusalam
AU  - Kovačević, Tihomir
AU  - Rusmirović, Jelena
AU  - Tomić, Nataša
AU  - Brzić, Saša
AU  - Bogosavljavić, Marica
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4168
AB  - Two types of alumina particles, commercial (c-Al2O3) and iron doped (Fe-Al2O3), were functionalized with 3-(aminopropyl)trimethoxysilane (one-step) and two-step consecutive process, i.e. firstly using 3-(aminopropyl)trimethoxysilane followed by methyl ester of linseed oil (biodiesel) to produce Al(2)O(3)ATPMS-BD reinforcement, respectively. The effect of modifier type and variable amount of alumina particles on the dynamical and mechanical properties of unsaturated polyester resin-based composites was studied. The highest improvement of the tensile strength and micro Vickers hardness, 78.1 and 163%, respectively, was obtained at 1.0 wt% of Fe-Al(2)O(3)APTMS-BD addition. The obtained multifunctional composites can be potentially applied in construction and mining industries.
PB  - Sage Publications Ltd, London
T2  - Journal of Composite Materials
T1  - Effect of surface activation of alumina particles on the performances of thermosetting-based composite materials
EP  - 2742
IS  - 19
SP  - 2727
VL  - 53
DO  - 10.1177/0021998319839133
ER  - 

@article{
author = "Drah, Abdusalam and Kovačević, Tihomir and Rusmirović, Jelena and Tomić, Nataša and Brzić, Saša and Bogosavljavić, Marica and Marinković, Aleksandar",
year = "2019",
abstract = "Two types of alumina particles, commercial (c-Al2O3) and iron doped (Fe-Al2O3), were functionalized with 3-(aminopropyl)trimethoxysilane (one-step) and two-step consecutive process, i.e. firstly using 3-(aminopropyl)trimethoxysilane followed by methyl ester of linseed oil (biodiesel) to produce Al(2)O(3)ATPMS-BD reinforcement, respectively. The effect of modifier type and variable amount of alumina particles on the dynamical and mechanical properties of unsaturated polyester resin-based composites was studied. The highest improvement of the tensile strength and micro Vickers hardness, 78.1 and 163%, respectively, was obtained at 1.0 wt% of Fe-Al(2)O(3)APTMS-BD addition. The obtained multifunctional composites can be potentially applied in construction and mining industries.",
publisher = "Sage Publications Ltd, London",
journal = "Journal of Composite Materials",
title = "Effect of surface activation of alumina particles on the performances of thermosetting-based composite materials",
pages = "2742-2727",
number = "19",
volume = "53",
doi = "10.1177/0021998319839133"
}

Drah, A., Kovačević, T., Rusmirović, J., Tomić, N., Brzić, S., Bogosavljavić, M.,& Marinković, A.. (2019). Effect of surface activation of alumina particles on the performances of thermosetting-based composite materials. in Journal of Composite Materials
Sage Publications Ltd, London., 53(19), 2727-2742.
https://doi.org/10.1177/0021998319839133

Drah A, Kovačević T, Rusmirović J, Tomić N, Brzić S, Bogosavljavić M, Marinković A. Effect of surface activation of alumina particles on the performances of thermosetting-based composite materials. in Journal of Composite Materials. 2019;53(19):2727-2742.
doi:10.1177/0021998319839133 .

Drah, Abdusalam, Kovačević, Tihomir, Rusmirović, Jelena, Tomić, Nataša, Brzić, Saša, Bogosavljavić, Marica, Marinković, Aleksandar, "Effect of surface activation of alumina particles on the performances of thermosetting-based composite materials" in Journal of Composite Materials, 53, no. 19 (2019):2727-2742,
https://doi.org/10.1177/0021998319839133 . .

TY  - JOUR
AU  - Milošević, Milena D.
AU  - Daničić, Dunja
AU  - Kovačina, Jovanka N.
AU  - Bugarčić, Mladen
AU  - Rusmirović, Jelena
AU  - Kovačević, Tihomir
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4271
AB  - The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and their use in alkyd based coatings to improve anticorrosive properties is presented in this work. Two methods of tannin modification were applied: direct method using ammonium hydroxide, ammonium hydroxide/ammonium chloride buffer or diethylenetriamine (DETA); and a two-step method including tannin modification with epichlorohydrin (ECH) in first step to produce epoxy modified tannin, ET, and further modification with heteroaromatic amines or linseed oil fatty acids (LFA) in second step. The obtained anticorrosive additives were characterized using ATR-FTIR, 1H and 13C NMR spectroscopies and elemental analysis. Epoxy, amino, hydroxyl, acid and iodine values of the synthesized inhibitors were determined according to standard methods. The prepared alkyd coating with tannin inhibitors was tested according to standard SRPS EN ISO 4628 method. Anticorrosive coating containing modified tannin based additive showed increased anticorrosive properties, good adhesion and coverage comparing to the coating with zinc phosphate additive. The alkyd coating films based on ET-LFA and ET modified with 2-amino-5-mercapto-1,3,4-thiadiazole showed best anticorrosive results.
AB  - U ovom radu prikazana je sinteza antikorozionih aditiva na bazi hemijski modifikovanog tanina i njihova primena u alkidnim premazima u cilju poboljšanja antikorozionih svojstava. Prikazane su dve metode modifikacije tanina: direktna modifikacija tanina primenom amonijum-hidroksida, amonijum-hidroksid/amonijum-hlorid pufera ili dietilentriamina (DETA); i dvostepena modifikacija tanina koja u prvom stupnju uključuje modifikaciju epihlorhidrinom sa ciljem da se dobije tannin sa epoksi terminiranim funkcionalnim grupama, ET, i modifikaciju ET tanina sa heteroaromatičnim aminima ili masnim kiselinama izolovanim iz lanenog ulja (LFA) u drugom stupnju. Sintetisani antikorozioni aditivi su okarakterisani primenom ATR-FTIR, 1H i 13C NMR spektroskopija, i elementalnom analizom. Sadržaj epoksi, amino, hidroksilnih i karboksilnih grupa i vrednost jodnog broja sintetisanih aditiva određen je prema standardnim metodama. Alkidni premazi koji sadrže antikorozione aditive na bazi modifikovanog tanina ispitani su prema standardnoj SRPS EN ISO 4628 metodi. Antikorozivni alkidni premazi na bazi modfikovanih tanina pokazali su poboljšane antikorozione karakteristike i adheziju u poređenju sa alkidnim premazom na bazi cink-fosfata. Alkidni premazi koji sadrže dvostepeno modifikovani tanin sa LFA i 2-amino-5-merkapto-1,3,4-tiadiazolom pokazali su najbolje antikorozione karakteristike.
PB  - Engineering Society for Corrosion, Belgrade, Serbia
T2  - Zaštita materijala
T1  - Modified tannins for alkyd based anticorrosive coatings
T1  - Primena modifikovanih tanina u antikorozionim alkidnim premazima
EP  - 95
IS  - 1
SP  - 81
VL  - 60
DO  - 10.5937/zasmat1901081M
ER  - 

@article{
author = "Milošević, Milena D. and Daničić, Dunja and Kovačina, Jovanka N. and Bugarčić, Mladen and Rusmirović, Jelena and Kovačević, Tihomir and Marinković, Aleksandar",
year = "2019",
abstract = "The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and their use in alkyd based coatings to improve anticorrosive properties is presented in this work. Two methods of tannin modification were applied: direct method using ammonium hydroxide, ammonium hydroxide/ammonium chloride buffer or diethylenetriamine (DETA); and a two-step method including tannin modification with epichlorohydrin (ECH) in first step to produce epoxy modified tannin, ET, and further modification with heteroaromatic amines or linseed oil fatty acids (LFA) in second step. The obtained anticorrosive additives were characterized using ATR-FTIR, 1H and 13C NMR spectroscopies and elemental analysis. Epoxy, amino, hydroxyl, acid and iodine values of the synthesized inhibitors were determined according to standard methods. The prepared alkyd coating with tannin inhibitors was tested according to standard SRPS EN ISO 4628 method. Anticorrosive coating containing modified tannin based additive showed increased anticorrosive properties, good adhesion and coverage comparing to the coating with zinc phosphate additive. The alkyd coating films based on ET-LFA and ET modified with 2-amino-5-mercapto-1,3,4-thiadiazole showed best anticorrosive results., U ovom radu prikazana je sinteza antikorozionih aditiva na bazi hemijski modifikovanog tanina i njihova primena u alkidnim premazima u cilju poboljšanja antikorozionih svojstava. Prikazane su dve metode modifikacije tanina: direktna modifikacija tanina primenom amonijum-hidroksida, amonijum-hidroksid/amonijum-hlorid pufera ili dietilentriamina (DETA); i dvostepena modifikacija tanina koja u prvom stupnju uključuje modifikaciju epihlorhidrinom sa ciljem da se dobije tannin sa epoksi terminiranim funkcionalnim grupama, ET, i modifikaciju ET tanina sa heteroaromatičnim aminima ili masnim kiselinama izolovanim iz lanenog ulja (LFA) u drugom stupnju. Sintetisani antikorozioni aditivi su okarakterisani primenom ATR-FTIR, 1H i 13C NMR spektroskopija, i elementalnom analizom. Sadržaj epoksi, amino, hidroksilnih i karboksilnih grupa i vrednost jodnog broja sintetisanih aditiva određen je prema standardnim metodama. Alkidni premazi koji sadrže antikorozione aditive na bazi modifikovanog tanina ispitani su prema standardnoj SRPS EN ISO 4628 metodi. Antikorozivni alkidni premazi na bazi modfikovanih tanina pokazali su poboljšane antikorozione karakteristike i adheziju u poređenju sa alkidnim premazom na bazi cink-fosfata. Alkidni premazi koji sadrže dvostepeno modifikovani tanin sa LFA i 2-amino-5-merkapto-1,3,4-tiadiazolom pokazali su najbolje antikorozione karakteristike.",
publisher = "Engineering Society for Corrosion, Belgrade, Serbia",
journal = "Zaštita materijala",
title = "Modified tannins for alkyd based anticorrosive coatings, Primena modifikovanih tanina u antikorozionim alkidnim premazima",
pages = "95-81",
number = "1",
volume = "60",
doi = "10.5937/zasmat1901081M"
}

Milošević, M. D., Daničić, D., Kovačina, J. N., Bugarčić, M., Rusmirović, J., Kovačević, T.,& Marinković, A.. (2019). Modified tannins for alkyd based anticorrosive coatings. in Zaštita materijala
Engineering Society for Corrosion, Belgrade, Serbia., 60(1), 81-95.
https://doi.org/10.5937/zasmat1901081M

Milošević MD, Daničić D, Kovačina JN, Bugarčić M, Rusmirović J, Kovačević T, Marinković A. Modified tannins for alkyd based anticorrosive coatings. in Zaštita materijala. 2019;60(1):81-95.
doi:10.5937/zasmat1901081M .

Milošević, Milena D., Daničić, Dunja, Kovačina, Jovanka N., Bugarčić, Mladen, Rusmirović, Jelena, Kovačević, Tihomir, Marinković, Aleksandar, "Modified tannins for alkyd based anticorrosive coatings" in Zaštita materijala, 60, no. 1 (2019):81-95,
https://doi.org/10.5937/zasmat1901081M . .

TY  - JOUR
AU  - Kovačević, Tihomir
AU  - Rusmirović, Jelena
AU  - Tomić, Nataša
AU  - Mladenović, Goran
AU  - Milosević, Miloš
AU  - Mitrović, Nenad
AU  - Marinković, Aleksandar
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4310
AB  - The investigation of the influence of acid/base treatment and addition level of non-metallic fractions (NMFs), obtained by processing of printed circuit boards, on the mechanical properties and shrinkage of unsaturated polyester resin (UPR)-based composites was main topic presented in this paper. NMF particles were treated using four different oxidative/etching agents: H2SO4/KMnO4 (NMF1), H2SO4/HNO3 (NMF2), HNO3 (NMF3), and NaOH (NMF4). Treated NMF(1-4) particles were characterized using fourier transform infrared, Boehm titration, optical microscopy and SEM analysis. Tensile strength and micro Vickers hardness of UPR/NMF(1-4) composites were the most improved with addition of 0.5wt% of filler, for 5.9-24.7%, in comparison to composite filled with non-treated NMF particles. Cross-linking density (nu), storage, and loss modulus (G' and G''), damping factor (tan delta) and glass transition temperature (T-g) of the composites were determined from the dynamic-mechanical analysis (DMA) testing. Shrinkage measurements, performed using Aramis 6.2.0, showed significant improvement in shrinkage reducing, for 17.8-30.6%, by introduction the oxidized NMF particles. Qualitative/quantitative evaluation of NMF(1-4) surface functionalities helped in understanding their influences on mechanical, DMA and shrinkage properties change of studied composites. POLYM. COMPOS., 40:1170-1186, 2019.
PB  - Wiley, Hoboken
T2  - Polymer Composites
T1  - Effects of oxidized/treated non-metallic fillers obtained from waste printed circuit boards on mechanical properties and shrinkage of unsaturated polyester-based composites
EP  - 1186
IS  - 3
SP  - 1170
VL  - 40
DO  - 10.1002/pc.24827
ER  - 

@article{
author = "Kovačević, Tihomir and Rusmirović, Jelena and Tomić, Nataša and Mladenović, Goran and Milosević, Miloš and Mitrović, Nenad and Marinković, Aleksandar",
year = "2019",
abstract = "The investigation of the influence of acid/base treatment and addition level of non-metallic fractions (NMFs), obtained by processing of printed circuit boards, on the mechanical properties and shrinkage of unsaturated polyester resin (UPR)-based composites was main topic presented in this paper. NMF particles were treated using four different oxidative/etching agents: H2SO4/KMnO4 (NMF1), H2SO4/HNO3 (NMF2), HNO3 (NMF3), and NaOH (NMF4). Treated NMF(1-4) particles were characterized using fourier transform infrared, Boehm titration, optical microscopy and SEM analysis. Tensile strength and micro Vickers hardness of UPR/NMF(1-4) composites were the most improved with addition of 0.5wt% of filler, for 5.9-24.7%, in comparison to composite filled with non-treated NMF particles. Cross-linking density (nu), storage, and loss modulus (G' and G''), damping factor (tan delta) and glass transition temperature (T-g) of the composites were determined from the dynamic-mechanical analysis (DMA) testing. Shrinkage measurements, performed using Aramis 6.2.0, showed significant improvement in shrinkage reducing, for 17.8-30.6%, by introduction the oxidized NMF particles. Qualitative/quantitative evaluation of NMF(1-4) surface functionalities helped in understanding their influences on mechanical, DMA and shrinkage properties change of studied composites. POLYM. COMPOS., 40:1170-1186, 2019.",
publisher = "Wiley, Hoboken",
journal = "Polymer Composites",
title = "Effects of oxidized/treated non-metallic fillers obtained from waste printed circuit boards on mechanical properties and shrinkage of unsaturated polyester-based composites",
pages = "1186-1170",
number = "3",
volume = "40",
doi = "10.1002/pc.24827"
}

Kovačević, T., Rusmirović, J., Tomić, N., Mladenović, G., Milosević, M., Mitrović, N.,& Marinković, A.. (2019). Effects of oxidized/treated non-metallic fillers obtained from waste printed circuit boards on mechanical properties and shrinkage of unsaturated polyester-based composites. in Polymer Composites
Wiley, Hoboken., 40(3), 1170-1186.
https://doi.org/10.1002/pc.24827

Kovačević T, Rusmirović J, Tomić N, Mladenović G, Milosević M, Mitrović N, Marinković A. Effects of oxidized/treated non-metallic fillers obtained from waste printed circuit boards on mechanical properties and shrinkage of unsaturated polyester-based composites. in Polymer Composites. 2019;40(3):1170-1186.
doi:10.1002/pc.24827 .

Kovačević, Tihomir, Rusmirović, Jelena, Tomić, Nataša, Mladenović, Goran, Milosević, Miloš, Mitrović, Nenad, Marinković, Aleksandar, "Effects of oxidized/treated non-metallic fillers obtained from waste printed circuit boards on mechanical properties and shrinkage of unsaturated polyester-based composites" in Polymer Composites, 40, no. 3 (2019):1170-1186,
https://doi.org/10.1002/pc.24827 . .

TY  - JOUR
AU  - Rusmirović, Jelena
AU  - Obradović, Nina
AU  - Perendija, Jovana
AU  - Umićević, Ana
AU  - Kapidžić, Ana
AU  - Vlahović, Branislav
AU  - Pavlović, Vera P.
AU  - Marinković, Aleksandar
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/4223
AB  - Iron oxide, in the form of magnetite (MG)-functionalized porous wollastonite (WL), was used as an adsorbent for heavy metal ions (cadmium and nickel) and oxyanions (chromate and phosphate) removal from water. The porous WL was synthesized from calcium carbonate and siloxane by controlled sintering process using low molecular weight submicrosized poly(methyl methacrylate) as a pore-forming agent. The precipitation of MG nanoparticles was carried out directly by a polyol-medium solvothermal method or via branched amino/carboxylic acid cross-linker by solvent/nonsolvent method producing WL/MG and WL--APS/MG adsorbents, respectively. The structure/properties of MG functionalized WL was confirmed by applying FTIR, Raman, XRD, Mossbauer, and SEM analysis. Higher adsorption capacities of 73.126, 66.144, 64.168, and 63.456mgg(-1) for WL--APS/MG in relation to WL/MG of 55.450, 52.019, 48.132, and 47.382mgg(-1) for Cd2+, Ni2+, phosphate, and chromate, respectively, were obtained using nonlinear Langmuir model fitting. Adsorption phenomena were analyzed using monolayer statistical physics model for single adsorption with one energy. Kinetic study showed exceptionally higher pseudo-second-order rate constants for WL--APS/MG, e.g., 1.17-13.4 times, with respect to WL/MG indicating importance of both WL surface modification and controllable precipitation of MG on WL--APS.
PB  - Springer Heidelberg, Heidelberg
T2  - Environmental Science and Pollution Research
T1  - Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal
EP  - 12398
IS  - 12
SP  - 12379
VL  - 26
DO  - 10.1007/s11356-019-04625-0
ER  - 

@article{
author = "Rusmirović, Jelena and Obradović, Nina and Perendija, Jovana and Umićević, Ana and Kapidžić, Ana and Vlahović, Branislav and Pavlović, Vera P. and Marinković, Aleksandar and Pavlović, Vladimir B.",
year = "2019",
abstract = "Iron oxide, in the form of magnetite (MG)-functionalized porous wollastonite (WL), was used as an adsorbent for heavy metal ions (cadmium and nickel) and oxyanions (chromate and phosphate) removal from water. The porous WL was synthesized from calcium carbonate and siloxane by controlled sintering process using low molecular weight submicrosized poly(methyl methacrylate) as a pore-forming agent. The precipitation of MG nanoparticles was carried out directly by a polyol-medium solvothermal method or via branched amino/carboxylic acid cross-linker by solvent/nonsolvent method producing WL/MG and WL--APS/MG adsorbents, respectively. The structure/properties of MG functionalized WL was confirmed by applying FTIR, Raman, XRD, Mossbauer, and SEM analysis. Higher adsorption capacities of 73.126, 66.144, 64.168, and 63.456mgg(-1) for WL--APS/MG in relation to WL/MG of 55.450, 52.019, 48.132, and 47.382mgg(-1) for Cd2+, Ni2+, phosphate, and chromate, respectively, were obtained using nonlinear Langmuir model fitting. Adsorption phenomena were analyzed using monolayer statistical physics model for single adsorption with one energy. Kinetic study showed exceptionally higher pseudo-second-order rate constants for WL--APS/MG, e.g., 1.17-13.4 times, with respect to WL/MG indicating importance of both WL surface modification and controllable precipitation of MG on WL--APS.",
publisher = "Springer Heidelberg, Heidelberg",
journal = "Environmental Science and Pollution Research",
title = "Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal",
pages = "12398-12379",
number = "12",
volume = "26",
doi = "10.1007/s11356-019-04625-0"
}

Rusmirović, J., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V. P., Marinković, A.,& Pavlović, V. B.. (2019). Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. in Environmental Science and Pollution Research
Springer Heidelberg, Heidelberg., 26(12), 12379-12398.
https://doi.org/10.1007/s11356-019-04625-0

Rusmirović J, Obradović N, Perendija J, Umićević A, Kapidžić A, Vlahović B, Pavlović VP, Marinković A, Pavlović VB. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. in Environmental Science and Pollution Research. 2019;26(12):12379-12398.
doi:10.1007/s11356-019-04625-0 .

Rusmirović, Jelena, Obradović, Nina, Perendija, Jovana, Umićević, Ana, Kapidžić, Ana, Vlahović, Branislav, Pavlović, Vera P., Marinković, Aleksandar, Pavlović, Vladimir B., "Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal" in Environmental Science and Pollution Research, 26, no. 12 (2019):12379-12398,
https://doi.org/10.1007/s11356-019-04625-0 . .

TY  - JOUR
AU  - Filipović, Suzana
AU  - Obradović, Nina
AU  - Marković, Smilja
AU  - Đorđević, Antonije
AU  - Balać, Igor
AU  - Dapčević, Aleksandra
AU  - Rogan, Jelena
AU  - Pavlović, Vladimir B.
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3909
AB  - Corundum (alpha-alumina) is a suiTab. material for usage in various industry fields owing to its chemical stability, electrical and mechanical features. It is known that properties of ceramics could be modified by addition of different oxides, as well as by changing the consolidation parameters. In this respect, alumina was doped with 1 wt.% of Cr2O3, Mn2O3 and NiO, followed by 1 hour of mechanical activation in a high-energy planetary ball mill. A sensitive dilatometer was used for sintering of powder mixtures up to 1400 degrees C and recording the obtained dilatation. The final density varied between cca. 1.9 and 3.3 g/cm(3). Microstructural changes were detected by SEM measurements. Changes in electrical permittivity and loss tangent were associated with the preparation conditions (types of additives, duration of mechanical activation). For a given mixture, the sintering increases the relative permittivity and decreases losses, exhibiting the optimal values of 8.32 and 0.027, respectively, for the sample activated 60 minutes and sintered, with the addition of MnO2. Mechanical measurements indicate significant differences in strength with the addition of different transition metal oxides. Samples with Mn and Ni, activated and sintered, with strength of 121 and 86 MPa, respectively, have a significantly higher tensile strength than the other tested samples, due to their more compact microstructures.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Physical Properties of Sintered Alumina Doped with Different Oxides
EP  - 419
IS  - 4
SP  - 409
VL  - 50
DO  - 10.2298/SOS1804409F
ER  - 

@article{
author = "Filipović, Suzana and Obradović, Nina and Marković, Smilja and Đorđević, Antonije and Balać, Igor and Dapčević, Aleksandra and Rogan, Jelena and Pavlović, Vladimir B.",
year = "2018",
abstract = "Corundum (alpha-alumina) is a suiTab. material for usage in various industry fields owing to its chemical stability, electrical and mechanical features. It is known that properties of ceramics could be modified by addition of different oxides, as well as by changing the consolidation parameters. In this respect, alumina was doped with 1 wt.% of Cr2O3, Mn2O3 and NiO, followed by 1 hour of mechanical activation in a high-energy planetary ball mill. A sensitive dilatometer was used for sintering of powder mixtures up to 1400 degrees C and recording the obtained dilatation. The final density varied between cca. 1.9 and 3.3 g/cm(3). Microstructural changes were detected by SEM measurements. Changes in electrical permittivity and loss tangent were associated with the preparation conditions (types of additives, duration of mechanical activation). For a given mixture, the sintering increases the relative permittivity and decreases losses, exhibiting the optimal values of 8.32 and 0.027, respectively, for the sample activated 60 minutes and sintered, with the addition of MnO2. Mechanical measurements indicate significant differences in strength with the addition of different transition metal oxides. Samples with Mn and Ni, activated and sintered, with strength of 121 and 86 MPa, respectively, have a significantly higher tensile strength than the other tested samples, due to their more compact microstructures.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Physical Properties of Sintered Alumina Doped with Different Oxides",
pages = "419-409",
number = "4",
volume = "50",
doi = "10.2298/SOS1804409F"
}

Filipović, S., Obradović, N., Marković, S., Đorđević, A., Balać, I., Dapčević, A., Rogan, J.,& Pavlović, V. B.. (2018). Physical Properties of Sintered Alumina Doped with Different Oxides. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 50(4), 409-419.
https://doi.org/10.2298/SOS1804409F

Filipović S, Obradović N, Marković S, Đorđević A, Balać I, Dapčević A, Rogan J, Pavlović VB. Physical Properties of Sintered Alumina Doped with Different Oxides. in Science of Sintering. 2018;50(4):409-419.
doi:10.2298/SOS1804409F .

Filipović, Suzana, Obradović, Nina, Marković, Smilja, Đorđević, Antonije, Balać, Igor, Dapčević, Aleksandra, Rogan, Jelena, Pavlović, Vladimir B., "Physical Properties of Sintered Alumina Doped with Different Oxides" in Science of Sintering, 50, no. 4 (2018):409-419,
https://doi.org/10.2298/SOS1804409F . .

TY  - JOUR
AU  - Tomić, Miloš
AU  - Dunjić, Branko
AU  - Nikolić, Marija
AU  - Maletaškić, Jelena
AU  - Pavlović, Vladimir B.
AU  - Bajat, Jelena
AU  - Đonlagić, Jasna
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3985
AB  - The major aims of this paper are the investigation of the effects of the mixing procedure and the montmorillonite (Mt) surface modification on the structure (optical microscopy, XRD, TEM, SEM), rheological, mechanical properties (DMA, tensile test) and corrosion stability (electrochemical impedance spectroscopy) of clay mineral/epoxy nanocomposite (CPN). Two series of CPN samples were prepared based on diglycidyl ether of bisphenol A (DGEBA) and polyamidoamine curing agent with three organophilic Mt and sodium-montmorillonite (1 wt%). Mt were mixed with DGEBA solution in the powder (direct mixing) and in the form of dispersions, preswollen in a commercial coating thinner (solution intercalation). The commercial Mt (Cloisite 30B) modified by quaternary alkylammonium ions bearing hydroxyl groups and especially Mt functionalized by primary (HDA(+)-Mt) alkylammonium ions, at loadings close to cation exchange capacity (CRC), were significantly swollen by thinner and further uniformly dispersed into CPN. Meanwhile, low gel volumes in thinner were found for more hydrophobic Mt (Cloisite 15A). The compatibility of Mt with solvents was well described by solubility and Flory-Huggins interaction parameters. In contrast to the direct incorporation of Mt powders in CPN, swelling enhanced intercalation of epoxy matrix into Mt, and for HDA(+)-Mt based CPN interlayer spacing reached 4.4 nm. The usage of HDA(+)-Mt organoclay and solution intercalation procedure provided the highest enhancement in rheological parameters (G', G", of Mt/epoxy dispersions and glassy storage modulus, Young's modulus and barrier properties of cured CPN.
PB  - Elsevier Science Bv, Amsterdam
T2  - Applied Clay Science
T1  - Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods
EP  - 63
SP  - 52
VL  - 154
DO  - 10.1016/j.clay.2017.12.047
ER  - 

@article{
author = "Tomić, Miloš and Dunjić, Branko and Nikolić, Marija and Maletaškić, Jelena and Pavlović, Vladimir B. and Bajat, Jelena and Đonlagić, Jasna",
year = "2018",
abstract = "The major aims of this paper are the investigation of the effects of the mixing procedure and the montmorillonite (Mt) surface modification on the structure (optical microscopy, XRD, TEM, SEM), rheological, mechanical properties (DMA, tensile test) and corrosion stability (electrochemical impedance spectroscopy) of clay mineral/epoxy nanocomposite (CPN). Two series of CPN samples were prepared based on diglycidyl ether of bisphenol A (DGEBA) and polyamidoamine curing agent with three organophilic Mt and sodium-montmorillonite (1 wt%). Mt were mixed with DGEBA solution in the powder (direct mixing) and in the form of dispersions, preswollen in a commercial coating thinner (solution intercalation). The commercial Mt (Cloisite 30B) modified by quaternary alkylammonium ions bearing hydroxyl groups and especially Mt functionalized by primary (HDA(+)-Mt) alkylammonium ions, at loadings close to cation exchange capacity (CRC), were significantly swollen by thinner and further uniformly dispersed into CPN. Meanwhile, low gel volumes in thinner were found for more hydrophobic Mt (Cloisite 15A). The compatibility of Mt with solvents was well described by solubility and Flory-Huggins interaction parameters. In contrast to the direct incorporation of Mt powders in CPN, swelling enhanced intercalation of epoxy matrix into Mt, and for HDA(+)-Mt based CPN interlayer spacing reached 4.4 nm. The usage of HDA(+)-Mt organoclay and solution intercalation procedure provided the highest enhancement in rheological parameters (G', G", of Mt/epoxy dispersions and glassy storage modulus, Young's modulus and barrier properties of cured CPN.",
publisher = "Elsevier Science Bv, Amsterdam",
journal = "Applied Clay Science",
title = "Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods",
pages = "63-52",
volume = "154",
doi = "10.1016/j.clay.2017.12.047"
}

Tomić, M., Dunjić, B., Nikolić, M., Maletaškić, J., Pavlović, V. B., Bajat, J.,& Đonlagić, J.. (2018). Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods. in Applied Clay Science
Elsevier Science Bv, Amsterdam., 154, 52-63.
https://doi.org/10.1016/j.clay.2017.12.047

Tomić M, Dunjić B, Nikolić M, Maletaškić J, Pavlović VB, Bajat J, Đonlagić J. Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods. in Applied Clay Science. 2018;154:52-63.
doi:10.1016/j.clay.2017.12.047 .

Tomić, Miloš, Dunjić, Branko, Nikolić, Marija, Maletaškić, Jelena, Pavlović, Vladimir B., Bajat, Jelena, Đonlagić, Jasna, "Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods" in Applied Clay Science, 154 (2018):52-63,
https://doi.org/10.1016/j.clay.2017.12.047 . .

TY  - JOUR
AU  - Rusmirović, Jelena
AU  - Rančić, Milica
AU  - Pavlović, Vladimir B.
AU  - Rakić, Vesna M.
AU  - Stevanović, Sanja
AU  - Đonlagić, Jasna
AU  - Marinković, Aleksandar
PY  - 2018
UR  - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3879
AB  - Unsaturated fatty acid (FA)-modified nanocellulose (m-NC) shows potential application in improving mechanical properties of unsaturated polyester/m-NC nanocomposites (UPe/m-NC). A polyester matrix is obtained by polycondensation of maleic anhydride and products of poly(ethylene terephthalate) depolymerization with propylene glycol. Two methods of NC modification are performed: direct esterification with oleic acid, linseed, or sunflower oil FAs, and esterification/amidation with maleic acid/ethylene diamine (MA/EDA) bridging group followed by amidation with methyl ester of FAs. Increases of stress at break in the ranges from 148.8% to 181.4% and from 155.8% to193.0% for UPe/m-NC composites loaded with 1 wt% of NC modified directly or via MA/EDA cross-linker, respectively, are obtained. Results of the modeling of tensile modulus, by using the Cox-Krenchel model, show good agreement with experimentally obtained data. The effect of FAs' cross-linking capabilities on the dynamic-mechanical and thermal properties of the UPe/m-NC is studied. Cross-linking density, modulus, and T-g of the nanocomposite show appropriate relation with the unsaturation extent/structure of NC modification.
PB  - Wiley-VCH Verlag Gmbh, Weinheim
T2  - Macromolecular Materials and Engineering
T1  - Cross-Linkable Modified Nanocellulose/Polyester Resin-Based Composites: Effect of Unsaturated Fatty Acid Nanocellulose Modification on Material Performances
IS  - 8
VL  - 303
DO  - 10.1002/mame.201700648
ER  - 

@article{
author = "Rusmirović, Jelena and Rančić, Milica and Pavlović, Vladimir B. and Rakić, Vesna M. and Stevanović, Sanja and Đonlagić, Jasna and Marinković, Aleksandar",
year = "2018",
abstract = "Unsaturated fatty acid (FA)-modified nanocellulose (m-NC) shows potential application in improving mechanical properties of unsaturated polyester/m-NC nanocomposites (UPe/m-NC). A polyester matrix is obtained by polycondensation of maleic anhydride and products of poly(ethylene terephthalate) depolymerization with propylene glycol. Two methods of NC modification are performed: direct esterification with oleic acid, linseed, or sunflower oil FAs, and esterification/amidation with maleic acid/ethylene diamine (MA/EDA) bridging group followed by amidation with methyl ester of FAs. Increases of stress at break in the ranges from 148.8% to 181.4% and from 155.8% to193.0% for UPe/m-NC composites loaded with 1 wt% of NC modified directly or via MA/EDA cross-linker, respectively, are obtained. Results of the modeling of tensile modulus, by using the Cox-Krenchel model, show good agreement with experimentally obtained data. The effect of FAs' cross-linking capabilities on the dynamic-mechanical and thermal properties of the UPe/m-NC is studied. Cross-linking density, modulus, and T-g of the nanocomposite show appropriate relation with the unsaturation extent/structure of NC modification.",
publisher = "Wiley-VCH Verlag Gmbh, Weinheim",
journal = "Macromolecular Materials and Engineering",
title = "Cross-Linkable Modified Nanocellulose/Polyester Resin-Based Composites: Effect of Unsaturated Fatty Acid Nanocellulose Modification on Material Performances",
number = "8",
volume = "303",
doi = "10.1002/mame.201700648"
}

Rusmirović, J., Rančić, M., Pavlović, V. B., Rakić, V. M., Stevanović, S., Đonlagić, J.,& Marinković, A.. (2018). Cross-Linkable Modified Nanocellulose/Polyester Resin-Based Composites: Effect of Unsaturated Fatty Acid Nanocellulose Modification on Material Performances. in Macromolecular Materials and Engineering
Wiley-VCH Verlag Gmbh, Weinheim., 303(8).
https://doi.org/10.1002/mame.201700648

Rusmirović J, Rančić M, Pavlović VB, Rakić VM, Stevanović S, Đonlagić J, Marinković A. Cross-Linkable Modified Nanocellulose/Polyester Resin-Based Composites: Effect of Unsaturated Fatty Acid Nanocellulose Modification on Material Performances. in Macromolecular Materials and Engineering. 2018;303(8).
doi:10.1002/mame.201700648 .

Rusmirović, Jelena, Rančić, Milica, Pavlović, Vladimir B., Rakić, Vesna M., Stevanović, Sanja, Đonlagić, Jasna, Marinković, Aleksandar, "Cross-Linkable Modified Nanocellulose/Polyester Resin-Based Composites: Effect of Unsaturated Fatty Acid Nanocellulose Modification on Material Performances" in Macromolecular Materials and Engineering, 303, no. 8 (2018),
https://doi.org/10.1002/mame.201700648 . .