Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion
Само за регистроване кориснике
2018
Чланак у часопису (Објављена верзија)
Метаподаци
Приказ свих података о документуАпстракт
effect of initial microstructure on the mechanical properties and fracture mode of the Ti-6Al-4V ELI alloy subjected to the high-pressure torsion (HPT) processing at room temperature and 500 degrees C was investigated. In this purpose, the four different microstructures (fully lamellar, martensitic, equiaxed and globular microstructures) were developed by the proper heat treatments. The results showed that the application of the HPT processing provided substantial microstructural refinement, independent on the alloy initial microstructure. As a consequence, the alloy hardness, tensile strength and ductility significantly increased. At the same time, the elastic modulus of the HPT-processed alloy is almost 2 times lower as compared to that of the alloy in the initial heat treated state. The obtained improvements strongly depend on the alloy initial microstructure and HPT processing temperature. It was found that the initial martensitic microstructure is beneficial to improve the hardnes...s, tensile and fracture properties. The HPT processing at 500 degrees C enhanced them more effectively. After the warm HPT processing, alloy with the initial martensitic microstructure exhibited exceptional hardness (455 MPa), high ultimate tensile strength (1546 MPa), high elongation to failure (18.8%) and low elastic modulus (78.6 GPa). Although the alloy with initial fully lamellar microstructure displayed the lowest elastic modulus (68 GPa), the ultrafine and homogeneous (alpha + beta) two-phase microstructure produced by the HPT processing of the alloy with initial martensitic microstructure offered the best combination of the strength-ductility balance and strength-to-elastic modulus ratio (19.8 x 10(-3)). The complex fracture process, involving transgranular quasi-cleavage and ductile dimple fracture mode, corresponded to the changes in ductility.
Кључне речи:
Ti-based alloy / High-pressure torsion / Microstructure / Mechanical properties / FractureИзвор:
Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 2018, 736, 175-192Издавач:
- Elsevier Science Sa, Lausanne
Финансирање / пројекти:
- Микромеханички критеријуми оштећења и лома (RS-174004)
- Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Leoben, Austria
- Laboratory for Advanced Nuclear Energy, Institute of Innovative Research, Tokyo Institute of Technology, Tokyo, Japan
DOI: 10.1016/j.msea.2018.08.094
ISSN: 0921-5093
WoS: 000447573400019
Scopus: 2-s2.0-85052870387
Институција/група
Tehnološko-metalurški fakultetTY - JOUR AU - Cvijović-Alagić, Ivana AU - Cvijović, Zorica AU - Maletaškić, Jelena AU - Rakin, Marko PY - 2018 UR - http://TechnoRep.tmf.bg.ac.rs/handle/123456789/3929 AB - effect of initial microstructure on the mechanical properties and fracture mode of the Ti-6Al-4V ELI alloy subjected to the high-pressure torsion (HPT) processing at room temperature and 500 degrees C was investigated. In this purpose, the four different microstructures (fully lamellar, martensitic, equiaxed and globular microstructures) were developed by the proper heat treatments. The results showed that the application of the HPT processing provided substantial microstructural refinement, independent on the alloy initial microstructure. As a consequence, the alloy hardness, tensile strength and ductility significantly increased. At the same time, the elastic modulus of the HPT-processed alloy is almost 2 times lower as compared to that of the alloy in the initial heat treated state. The obtained improvements strongly depend on the alloy initial microstructure and HPT processing temperature. It was found that the initial martensitic microstructure is beneficial to improve the hardness, tensile and fracture properties. The HPT processing at 500 degrees C enhanced them more effectively. After the warm HPT processing, alloy with the initial martensitic microstructure exhibited exceptional hardness (455 MPa), high ultimate tensile strength (1546 MPa), high elongation to failure (18.8%) and low elastic modulus (78.6 GPa). Although the alloy with initial fully lamellar microstructure displayed the lowest elastic modulus (68 GPa), the ultrafine and homogeneous (alpha + beta) two-phase microstructure produced by the HPT processing of the alloy with initial martensitic microstructure offered the best combination of the strength-ductility balance and strength-to-elastic modulus ratio (19.8 x 10(-3)). The complex fracture process, involving transgranular quasi-cleavage and ductile dimple fracture mode, corresponded to the changes in ductility. PB - Elsevier Science Sa, Lausanne T2 - Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing T1 - Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion EP - 192 SP - 175 VL - 736 DO - 10.1016/j.msea.2018.08.094 ER -
@article{ author = "Cvijović-Alagić, Ivana and Cvijović, Zorica and Maletaškić, Jelena and Rakin, Marko", year = "2018", abstract = "effect of initial microstructure on the mechanical properties and fracture mode of the Ti-6Al-4V ELI alloy subjected to the high-pressure torsion (HPT) processing at room temperature and 500 degrees C was investigated. In this purpose, the four different microstructures (fully lamellar, martensitic, equiaxed and globular microstructures) were developed by the proper heat treatments. The results showed that the application of the HPT processing provided substantial microstructural refinement, independent on the alloy initial microstructure. As a consequence, the alloy hardness, tensile strength and ductility significantly increased. At the same time, the elastic modulus of the HPT-processed alloy is almost 2 times lower as compared to that of the alloy in the initial heat treated state. The obtained improvements strongly depend on the alloy initial microstructure and HPT processing temperature. It was found that the initial martensitic microstructure is beneficial to improve the hardness, tensile and fracture properties. The HPT processing at 500 degrees C enhanced them more effectively. After the warm HPT processing, alloy with the initial martensitic microstructure exhibited exceptional hardness (455 MPa), high ultimate tensile strength (1546 MPa), high elongation to failure (18.8%) and low elastic modulus (78.6 GPa). Although the alloy with initial fully lamellar microstructure displayed the lowest elastic modulus (68 GPa), the ultrafine and homogeneous (alpha + beta) two-phase microstructure produced by the HPT processing of the alloy with initial martensitic microstructure offered the best combination of the strength-ductility balance and strength-to-elastic modulus ratio (19.8 x 10(-3)). The complex fracture process, involving transgranular quasi-cleavage and ductile dimple fracture mode, corresponded to the changes in ductility.", publisher = "Elsevier Science Sa, Lausanne", journal = "Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing", title = "Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion", pages = "192-175", volume = "736", doi = "10.1016/j.msea.2018.08.094" }
Cvijović-Alagić, I., Cvijović, Z., Maletaškić, J.,& Rakin, M.. (2018). Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion. in Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing Elsevier Science Sa, Lausanne., 736, 175-192. https://doi.org/10.1016/j.msea.2018.08.094
Cvijović-Alagić I, Cvijović Z, Maletaškić J, Rakin M. Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion. in Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing. 2018;736:175-192. doi:10.1016/j.msea.2018.08.094 .
Cvijović-Alagić, Ivana, Cvijović, Zorica, Maletaškić, Jelena, Rakin, Marko, "Initial microstructure effect on the mechanical properties of Ti-6Al-4V ELI alloy processed by high-pressure torsion" in Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 736 (2018):175-192, https://doi.org/10.1016/j.msea.2018.08.094 . .