Претраживање
Приказ резултата 11-19 од 19
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
(ETRAN, 2022)
Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Investigation of Possibility for Stabilization and Valorization of Electric Arc Furnace Dust and Glass From Electronic Waste
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
This paper presents investigation of possibility for electric arc furnace dust (EAFD) and electronic waste (e-waste) valorization trough stabilization process, in order to achieve concurrent management of these two serious ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART I: Effect of Synthesis Parameters on Chemical Composition, Microstructure and Morphology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
Kinetic and operational electrolysis parameters determine the polarization characteristics, electrodeposition current efficiency, morphology, chemical composition and microstructure of nickel/iron/tungsten alloy deposits. ...
Effect of milling and annealing on microstructural, electrical and magnetic properties of electrodeposited Ni-11.3 Fe-1.4w alloy
(International Institute for the Science of Sintering, Beograd, 2012)
A nanostructured Ni-11.3Fe-1.4W alloy deposit was obtained from an ammonium citrate bath at a current density of 600 mAcm-2. XRD analysis shows that the deposit contains an amorphous matrix having embedded nanocrystals of ...
Effect of Electrodeposition Current Density on the Microstructure and Magnetic Properties of Nickel-cobalt-molybdenum Alloy Powders
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Nanostructured nickel-cobalt-molybdenum alloy powders were electrodeposited from an ammonium sulfate bath. The powders mostly consist of an amorphous phase and a very small amount of nanocrystals with an mean size of less ...
Structural, Morphological and Electrical Properties of Alumina/YAG Composites as Solid Electrolyte for IT - SOFC
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
Alumina/YAG composites (AYX_t) with high relative density (99.2 %TD) were successfully obtained by mixing commercial alumina powder with different volume fractions of yttrium aluminium garnet (Y3Al5O12-YAG; 7, 14, 21 and ...