Претраживање
Приказ резултата 1-10 од 11
Thermal cycling behaviour of plasma sprayed nicr-al-co-y2o3 bond coat in thermal barrier coating system
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2019)
The aim of this study was to investigate the thermal cycling behaviour of NiCr-Al-Co-Y2O3 bond coating in thermal barrier coating (TBC) system with ZrO2-MgO as a top coating. The coatings were deposited by atmospheric ...
Temperature fields in linear stage of friction stir welding effect of different material properties
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2019)
Friction stir welding is one of the procedures for joining the parts in solid state. Thermo-mechanical simulation of the friction stir welding of high-strength aluminium alloys 2024 T3 and 2024 T351 is considered in this ...
Influence of material velocity on heat generation during linear welding stage of friction stir welding
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2016)
The heat generated during friction stir welding process depends on plastic deformation of the material and friction between the tool and the material. In this work, heat generation is analysed with respect to the material ...
Assessment of the burden of disease due to PM2.5 air pollution for the Belgrade district
(VINČA Institute of Nuclear Sciences, 2023)
The health effects attributed to exposure to ambient PM2.5 concentrations
above 10 μg/m3
by using the AirQ+ modeling software were assessed. The
hourly concentrations of PM2.5 were collected from 13 air pollution
monitoring ...
AERMOD air dispersion modeling and health risks of gas and oil fueled heating plant emissions
(VINČA Institute of Nuclear Sciences, 2023)
A significant part of the population in Serbia relies on central heating systems during
the winter months, with around fifty heating plants in operation across the country.
Common fuels used in these plants primarily ...
Influence of friction stir welding parameters on properties of 2024 t3 aluminium alloy joints
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The aim of this work is to analyse the process of friction stir welding (FSW) of 3 mm thick aluminium plates made of high strength aluminium alloy - 2024 T3, as well as to assess the mechanical properties of the produced ...
Analysis of the tool plunge in friction stir welding comparison of aluminum alloys 2024 t3 and 2024 t351
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2016)
Temperature, plastic strain and heat generation during the plunge stage of the friction stir welding of high-strength aluminum alloys 2024 T3 and 2024 T351 are considered in this work. The plunging of the tool into the ...
Heat generation during plunge stage in friction stir welding
(Vinca Institute of Nuclear Sciences, 2013)
This paper deals with the heat generation in the Al alloy Al2024-T3 plate under different rotating speeds and plunge speeds during the plunge stage of friction stir welding. A 3-D finite element model is developed in the ...
Experimental and numerical thermo - mechanical analysis of friction stir welding of high - strength alluminium alloy
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
This paper presents experimental and numerical analysis of the change of temperature and force in the vertical direction during the friction stir welding of high-strength aluminium alloy 2024 T3. This procedure confirmed ...
Thermo-mechanical analysis of linear welding stage in friction stir welding Influence of Welding Parameters
(VINČA Institute of Nuclear Sciences, 2022)
The influence of friction stir welding parameters on thermo-mechanical behavior of the material during welding is analyzed. An aluminum alloy is considered (Al 2024 T351), and different rotating and welding speeds are ...