Претраживање
Приказ резултата 1-10 од 58
Structural characteristics of some ternary Ag-In-Sn alloys
(Savez inženjera metalurgije Srbije, Beograd, 2008)
The Ag-In-Sn system, as one of potential lead-free solder materials, was studied in this paper. The investigated alloys were chosen from two sections, with molar ratio of In:Sn equal to 1:4; 1:2. DTA, XRD, SEM and micro ...
The effect of heat treatment on toughness and wear resistance of Fe-Cr-C-Nb alloys / Uticaj termičke obrade na žilavost i otpornost na habanje Fe-Cr-C-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Alloying with niobium improves the mechanical properties of the high chromium irons. The alloy containing appriximately 3 %Nb gives the best compromise between wear resistance and toughness. These properties were improved ...
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheet
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheets was examined after cold rolling and annealing in the range of temperature from 220°C to 520°C, water quenching and natural aging. The low temperature annealed ...
Development of contemporary procedures for lead obtaining / Razvoj savremenih postupaka dobijanja olova
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Contemporary procedures of lead concentrates treatment were in different expansion during last thirty years. All procedures have in common the following: smelting reaction proceeds in solid-gas suspension, melting products ...
The influence of thermomechanical treatment on recrystallization of AlMg4.5Cu0.5 alloy
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behavior of an Al-Mg-Cu alloy (4.5 wt. %Mg and 0.45 wt %Cu) subjected to different thermomechanical treatments (TMTs) have been studied by means of light optical microscopy and hardness measurements. In ...
Dynamic recrystallization in M2 tool steel during friction welding
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Friction welding of M2 tool steel and 1730 quenched and tempered steel was performed with the aim to reveal the origin of extremely fine martensitic grain in M2 steel after welding. Taking into account thermomechanical ...
Fuel consumption analysis in cooper melting and refining plants / Analiza potrošnje energenata u pogonima za topljenje i rafinaciju bakra
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Cathode cooper production and refining include significant consumption of almost all-conventional fuel types. The given consumption is high in specific and in nominal way. Especially high fuel value content is on Cathode ...
Tensile properties of fiber-resin composites that consist of polyarmid fiber (Kevlar 129) and poly(vinilbutyral) / Zatezna svojstva polimernog kompozitnog materijala poliaramidna vlakna (Kevlar 129) - poli(vinilbutiral)(PVB)
(Savez inženjera metalurgije Srbije, Beograd, 2006)
Thanks to fact that composite material have usefully characteristic two or more materials, they are becoming more and more substitute standard materials in every field of technique they start to. In this study static ...
Synthesis and sintering of Cu-Al2O3 nanocomposite powders produced by a thermochemical route
(Savez inženjera metalurgije Srbije, Beograd, 2007)
By hydrometallurgy and powder metallurgy along with prognosis of physical-chemical properties, a synthesis of new improved materials can be successfully performed with in advance pre-set properties which is conditioned by ...
Properties of Cu-Al2O3 Powder and Compact Composites of Various Starting Particle Size Obtained by High-Energy Milling
(Savez inženjera metalurgije Srbije, 2009)
Copper-based composites were obtained using high energy milling. The inert gas-atomized prealloyed copper powder (average particle size - 30 μm) containing 2 wt.% Al, and the mixture of electrolytic copper powder (average ...