Претраживање
Приказ резултата 31-40 од 40
Preparation and Characterization of Novel Glycidyl Methacrylate/Clay Nanocomposites
(Science of SinteringScience of Sintering, 2022)
The impact of the type and amounts of nanofiller on the features of the glycidyl methacrylate-co-ethylene glycol dimethacrylate (GMA-co-EGDMA)/organomodified montmorillonite (OMt) nanocomposites that were prepared by in ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
The Influence of Powder Particle Size on Properties of Cu-Al2O3 Composites
(International Institute for the Science of Sintering (IISS), 2009)
Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size approximate to 30 mu m) and a mixture consisting of copper (average particle sizes approximate to 15 mu m and 30 mu m) and 4 wt.% of ...
The Mechanisms of Cavitation Erosion of Raw and Sintered Basalt
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
The paper analyzes the morphology of cavitation damage of raw and sintered basalt samples. The experiment was conducted using the ultrasonic vibratory cavitation test method according to the ASTM G-32 standard. During the ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass
(Science of Sintering, 2022)
The nucleation process of lithium germanium-phosphate glass was studied to determine the temperature range of nucleation and the temperature of the maximum nucleation rate. The differential thermal analysis (DTA), and ...
Novel Magnetic Polymer/bentonite Composite: Characterization and Application for Re(VII) and W(VI) Adsorption
(Science of Sintering, 2021)
A novel magnetic polymer/bentonite composite was prepared by suspension copolymerization of glycidyl methacrylate and ethylene glycol dimethacrylate in the presence of magnetic bentonite (MB-PGME) and functionalized with ...
Synthesis of Anatase Nanopowders by Sol-gel Method and Influence of Temperatures of Calcination to Their Photocatalitic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The titanium dioxide (TiO2) nanopowders were produced by sol-gel technique from tetrabutyl titanate as a precursor, varying the temperature of calcination (from 500 to 550 degrees C with the step of 10 degrees C). XRPD ...
Fast Oxide-Ion Conductors in Bi2O3-V2O5 System: Bi108-xVxO162+x(x=4-9) with 3 x 3 x 3 Superstructure
(Science of Sintering, 2021)
In this study, the possibility to stabilize O-2 ion conductors in Bi2O3-V2O5 system was investigated. Six pseudo-binary Bi2O3-V2O5 mixtures [3.50 lt x(V2O5) lt 8.50 mol%] were thermally treated at 1000 degrees C for 1 ...