Search
Now showing items 11-20 of 73
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Overview of the materials: Metals selection process / Strategija izbora metalnih materijala
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Overview of the metal material selection process will be subject of this paper. Interrelationship among design, materials and processing will be presented. Materials selection for a new design as well as materials substitution ...
Problems and prospect of Al-Mg alloys application in marine constructions
(Savez inženjera metalurgije Srbije, Beograd, 2006)
The position of steel as the most widely used material in the shipbuilding industry originates from the superior mechanical properties and low manufacturing costs The increasing demands for lowering the weight of different ...
The influence of the solidification rate on the interface shape and distribution of solute
(Savez inženjera metalurgije Srbije, Beograd, 2002)
In this paper investigation of the influence of the solidification conditions on the interface shape and distribution of solute during the solidification of AI-Cu alloy by vertical Bridgman method were investigated. The ...
Approximation of material behaviour of PLLA polymer in HAp/PLLA biocomposite material using nanoindentation and finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2007)
In this work, a combination of nanoindentation experiment and finite element modeling is proposed in order to obtain approximate material behavior of PLLA polymer in hydroxyapatite (HAp)/poly-L-lactide (PLLA) composite. ...
Rotating disk alumina precursor fiber formation process stability determination using image analysis
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Precursor fibers are made from the aluminium-hydroxide chloride based sols. The process stability can be influenced both by the fiber formation conditions and the rheology of the sol. The distance from the disk canter is ...
Studies of a wear resistant cast iron / Izučavanje belih gvožđa otpornih na habanje
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The objective of this investigation was to set down (on the base of the results obtained by the examination of white cast iron alloys with different content of the alloying elements) a correlation between chemical composition ...
Influence of vanadium content and colling rate on the stereological parameters of phases in the structure of Fe-C-Cr-V alloys / Uticaj sadržaja vanadijuma i brzine hlađenja na stereološke parametre faza u strukturi Fe-C-Cr-V legura
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper, the influence of vanadium content and cooling rate on the stereological parameters of phases present in the structure of Fe-C-Cr-V alloys. Experimental results indicate that both vanadium content and cooling ...
An improved method for thermal stability behavior characterization of silicon carbide/cordierite composite material
(Savez inženjera metalurgije Srbije, Beograd, 2007)
In the present work Mg-exchanged zeolit and silicon carbide were used as starting materials for obtaining cordierite/SiC composite ceramics with weight ratio 50:50. Samples were exposed to the water quench test from 950°C, ...