Претраживање
Приказ резултата 21-30 од 72
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Dependence of the solid-liquid interface structure on the solidification process parameters / Zavisnost strukture granice faza tečno-čvrsto od parametara procesa očvršćavanja
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Influence of the solidification rate, temperature gradient and initial concentration of the solute on the interface shape was investigated during solidification from the melt. The dependence of the microstructure on the ...
Image analysis of protective layer of zinc on steel obtained using the hot process / Analiza slike za karakterisanje zaštitnog sloja cinka na čeliku dobijenog toplim cinkovanjem
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The procedure for measuring the thickness of anticorrosion protective layer of zinc on steel is given. The metallographic images are used for this measurement. Results are statistically handled and results are used to ...
The influence of titanium and cerium on microstructure and properties of Fe-C-Cr-Nb alloys / Uticaj titana i cerijuma na mikrostrukturu i svojstva Fe-C-Cr-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2005)
In this paper, the influence of titanium and cerium on the microstructure and properties of Fe-C-Cr-Nb alloys are examined, in both as-cast and heat treated state. These elements affect the crystallisation process of ...
Thermomechanical processing of micro alloyed steels in Sartid A.D.: Part III - comparison of of Tnr temperatures determined on laboratory and industrial scale / Termomehanička prerada mikrolegiranih čelika koncerna Sartid: III deo - poređenje Tnr temperatura određenih u laboratorijskim i industrijskim uslovima
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The aim of this work was to compare the Tnr temperatures of microalloyed steels estimated on laboratory (Tnr**l) and industrial scale (Tnr**l). Laboratory and industrial scale are related to testing on high temperature ...
Possibilities of recycling of magnesium and magnesium alloys
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper are presented results of experimental investigation of processing of non oil-contaminated metal scrap based on magnesium and its alloys. These are the firs investigations of magnesium scrap recycling in Serbia ...
Characterization of wastewater streams from Bor site
(Savez inženjera metalurgije Srbije, Beograd, 2007)
This paper presents full characterization of wastewater streams within Bor copper mine. Seven different wastewater streams were identified and fully characterized (origin, flow rate, chemical and physical properties) on ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1. Investigations were performed on superalloy single crystals based Ni which were ...
Depozition of thin films by CVD techniques / Nanošenje tankih filmova CVD postupcima
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Chemical vapor deposition - (CVD) has rapidly grown in the last twenty years and applications of this fabrication process are now key elements in many industrial products, such as semiconductors, optoelectonics, optics, ...
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...