Претраживање
Приказ резултата 31-40 од 72
A case study of global steel properties database development: Key to steel / Primer razvoja globalne baze podataka osobina čelika - key to steel
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Key to Steel is the world’s most comprehensive database of steel materials developed to provide technical information to professional users worldwide. This paper describes development process that resulted in the biggest ...
FEM modeling of dynamic recrystallization in 304 stainless steel
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Series of isothermal uniaxial compression tests in the temperature range (600-1100°C) with two strain rates of 0.1 and 1.0 s"1 were performed with the aim to obtain input data for the finite elements modeling (FEM) of ...
Characterization of wastewater streams from Bor site
(Savez inženjera metalurgije Srbije, Beograd, 2007)
This paper presents full characterization of wastewater streams within Bor copper mine. Seven different wastewater streams were identified and fully characterized (origin, flow rate, chemical and physical properties) on ...
Application of instrumental methods in the investigation of properties and microstructure of construction concretes / Primena instrumentalnih metoda za ispitivanje svojstava i mikrostrukture konstukcionih betona
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Methods for the investigation of microstructure of construction concretes are presented in this paper. Concrete is a composite material, thus its microstructure consists of bonding agent (cement) and aggregate with predefined ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Effect of heating rate on precipitation of peak-aged Al-Li (8091) alloy: A quantitative approach
(Savez inženjera metalurgije Srbije, Beograd, 2010)
Samples of Al-Li (8091) alloy were solution treated at 540ºC for 30 min, water-quenched and continuously heated in oil at 0.05 and 0.1ºC/min rates, from room temperature to 190ºC when the peak hardness was achieved. Having ...
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Specific energy absorption capacity of glass-polyester composite tubes under static compressive loading
(Croatian Metallurgical Society, 2011)
The experimental determination of energy of glass-polyester composite tubes static fracture is done. The tubes are of defined structure and known processes of fabrication. The aim was to determine the possibility of their ...
Structural properties of Co, Ni and Mo powders obtained by electrochemical deposition
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Magnetic thin films based on iron group elements (Fe, Co, Ni) are currently used in computer's hard disk drives and in MEMS, whereas electrodeposition is a suitable method to obtain these materials. The powders of metals ...
Influence of vanadium content and colling rate on the stereological parameters of phases in the structure of Fe-C-Cr-V alloys / Uticaj sadržaja vanadijuma i brzine hlađenja na stereološke parametre faza u strukturi Fe-C-Cr-V legura
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper, the influence of vanadium content and cooling rate on the stereological parameters of phases present in the structure of Fe-C-Cr-V alloys. Experimental results indicate that both vanadium content and cooling ...