Претраживање
Приказ резултата 51-60 од 75
Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent
(International Institute for the Science of Sintering (IISS), 2022)
In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were ...
Evaluation of Adsorption Performance and Quantum Chemical Modeling of Pesticides Removal using Cell-MG Hybrid Adsorbent
(Science of Sintering, 2021)
Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, ...
The Influence of Powder Particle Size on Properties of Cu-Al2O3 Composites
(International Institute for the Science of Sintering (IISS), 2009)
Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size approximate to 30 mu m) and a mixture consisting of copper (average particle sizes approximate to 15 mu m and 30 mu m) and 4 wt.% of ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
Morphological and Structural Characterization of MgAl2O4 Spinel
(International Institute for the Science of Sintering (IISS), 2023)
Magnesium aluminate has the spinel structure along with good mechanical, chemical, and thermal properties. Magnesium aluminate has a wide range of applications including refractory ceramics, optically transparent ceramic ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
The Mechanisms of Cavitation Erosion of Raw and Sintered Basalt
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
The paper analyzes the morphology of cavitation damage of raw and sintered basalt samples. The experiment was conducted using the ultrasonic vibratory cavitation test method according to the ASTM G-32 standard. During the ...
Modeling of coating optical fibers with polymer-magnetic powder composite coating
(International Institute for the Science of Sintering, Beograd, 2002)
A mathematical model of forming a composite coating on optical fiber was established. The model is based on existing mathematical models for coating optical fibers with polymer coating and experimentally defined rheological ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass
(Science of Sintering, 2022)
The nucleation process of lithium germanium-phosphate glass was studied to determine the temperature range of nucleation and the temperature of the maximum nucleation rate. The differential thermal analysis (DTA), and ...