Претраживање
Приказ резултата 61-70 од 75
Deterioration Characterization during Thermal Shock Testing
(International Institute for the Science of Sintering (IISS), 2023)
Thermal shock stability plays a great role in the selection of optimal refractory material. Different methods of characterization were developed for this purpose, including the implementation of nondestructive testing. ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
Morphological and Structural Characterization of MgAl2O4 Spinel
(International Institute for the Science of Sintering (IISS), 2023)
Magnesium aluminate has the spinel structure along with good mechanical, chemical, and thermal properties. Magnesium aluminate has a wide range of applications including refractory ceramics, optically transparent ceramic ...
The Effect of Acrylate on the Properties and Machinability of Alumina Ceramics
(International Institute for the Science of Sintering (IISS), 2023)
Effect of methyl methacrylate (MMA) as a binder and heating treatment were investigated to improve green alumina compacts machinability. Properties of green compacts and their corresponding sintered samples prepared with ...
Novel Magnetic Polymer/bentonite Composite: Characterization and Application for Re(VII) and W(VI) Adsorption
(Science of Sintering, 2021)
A novel magnetic polymer/bentonite composite was prepared by suspension copolymerization of glycidyl methacrylate and ethylene glycol dimethacrylate in the presence of magnetic bentonite (MB-PGME) and functionalized with ...
Synthesis of Anatase Nanopowders by Sol-gel Method and Influence of Temperatures of Calcination to Their Photocatalitic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The titanium dioxide (TiO2) nanopowders were produced by sol-gel technique from tetrabutyl titanate as a precursor, varying the temperature of calcination (from 500 to 550 degrees C with the step of 10 degrees C). XRPD ...
Investigation on the Adsorption of the Carbamate Pesticide Methomyl from Aqueous Solution using Modified Co-Beta Zeolite Particles
(International Institute for the Science of Sintering (IISS), 2023)
Adsorption of carbamate pesticide Methomyl by Co-Beta Zeolite particles prepared by wet ion-exchange method from aqueous solutions was studied. The effect of zeolite and pesticide concentrations, pH value, and sintering ...
Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2017)
Mechanical shock of zircon based ceramic induced by cavitation erosion testing was investigated in this study. Several parameters were followed in order to determine level of material degradation during the cavitation ...
Influence of Raster Angle on Tensile Properties of FDM Additively Manufactured Plates made from Carbon Reinforced PET-G Material
(Belgrade : Association for ETRAN Society, 2023)
Tensile properties of thin plate specimens made from short carbon fiberreinforced PET-G material are experimentally evaluated for various raster angles(printing directions). In additive manufacturing (AM), raster angle is ...