Pretraživanje
Prikaz rezultata 1-10 od 41
Electrochemical deposition and characterization of Zn-Fe alloys / Elektrohemijsko taloženje i karakterizacija Zn-Fe legura
(Serbian Chemical Society, Belgrade, 2004)
Zn–Fe alloy electrochemically deposited on steel under various deposition conditions were investigated using anodic linear sweep voltammetry (ALSV) and X-ray diffraction (XRD) analysis for phase structure determination, ...
Electrodeposition and characterization of Fe-Mo alloys as cathodes for hydrogen evolution in the process of chlorate production / Elektrohemijsko taloženje i karakterizacija Fe-Mo legura kao katoda za reakciju izdvajanja vodonika u industrijskom procesu proizvodnje hlorata
(Serbian Chemical Society, Belgrade, 2005)
Fe–Mo alloys were electrodeposited from a pyrophosphate bath using a single diode rectified AC current. Their composition and morphology were investigated by SEM, optical microscopy and EDS, in order to determine the ...
Cross-section analysis of the morphology of electrodeposited copper obtained in the hydrogen co-deposition range / Morfologija poprečnog preseka prevlaka bakra dobijenih elektrohemijskim taloženjem u oblasti ko-depozicije vodonika
(Serbian Chemical Society, 2009)
Cross-section analysis of copper deposits electrodeposited in the hydrogen co-deposition range at a constant overpotential and in a pulsating overpotential (PO) regime was performed. It was shown that a complete structural ...
Electrochemical deposition and characterization of zinc-nickel alloys deposited by direct and reverse current / Elektrohemijsko taloženje i karakterizacija legura cink-nikal dobijenih konstantnom i reversnom strujom
(Serbian Chemical Society, Belgrade, 2005)
Zn-Ni alloys electrochemically deposited on steel under various deposition conditions were investigated. The alloys were deposited on a rotating disc electrode and on a steel panel from chloride solutions by direct and ...
Hardness response and adhesion of thin copper films on alloy substrates
(Belgrade: ETRAN – Society for electronics, telecommunication, computing, automatics and nuclear engineering, 2017)
Microhardness test is the most commonly used method for assessing the mechanical properties of thin films.This testing method uses controlled contact at a single point of an indenter and chosen material which induces the ...
Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces / Epoksidne kataforetske prevlake na aluminijumu i modifikovanim površinama aluminijuma
(Association of Chemical Engineers of Serbia, 2002)
The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium) were monitored during exposure to 3% NaCl ...
Epoxy coatings electrodeposited on steel electrochemically modified by Zn-Co alloys / Epoksidne kataforetske prevlake na čeliku modifikovanom Zn-Co legurama
(Engineering Society for Corrosion, Belgrade, Serbia, 2003)
The corrosion behavior of epoxy coatings electrodeposited on steel and steel modified by Zn-Co alloys deposited from chloride and sulphate baths were investigated during exposure to 3 % NaCl. The electrochemical impedance ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Inženjersko društvo za koroziju, Beograd, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...
The study of corrosion stability of organic epoxy protective coatings on aluminium and modified aluminium surfaces
(Soc Brasileira Quimica, Sao Paulo, 2005)
Epoxy coatings were formed by cathodic electrodeposition of an epoxy resin on aluminium and modified aluminium surfaces (phosphatized, chromatized-phosphatized and anodized aluminium) using a constant voltage method (resin ...