Претраживање
Приказ резултата 31-40 од 57
Influence of heat transfer conditions on determination of thermal shock resistance of refractories / Uticaj prenosa toplote na određivanje termostabilnosti vatrostalnog materijala
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The goal of this thesis was to determine the thermal shock resistance of alumina based refractories in the case of a heat transfer conditions different from the standard conditions given by quenching test JUS. B. D.8 319. ...
FEM modeling of dynamic recrystallization in 304 stainless steel
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Series of isothermal uniaxial compression tests in the temperature range (600-1100°C) with two strain rates of 0.1 and 1.0 s"1 were performed with the aim to obtain input data for the finite elements modeling (FEM) of ...
Possibilities of recycling of magnesium and magnesium alloys
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper are presented results of experimental investigation of processing of non oil-contaminated metal scrap based on magnesium and its alloys. These are the firs investigations of magnesium scrap recycling in Serbia ...
Characterization of wastewater streams from Bor site
(Savez inženjera metalurgije Srbije, Beograd, 2007)
This paper presents full characterization of wastewater streams within Bor copper mine. Seven different wastewater streams were identified and fully characterized (origin, flow rate, chemical and physical properties) on ...
Kinetics of crystallization silicon-(IV)-nitride / Kinetika kristalizacije silicijum-(IV)-nitrida
(Savez inženjera metalurgije Srbije, Beograd, 2003)
Amorphous covalent Si-C-N ceramics have been synthesized by pyrolysis polysilazanes. This part of experiment was done in Institute für Nichtmetallische Anorganische Materialien, Universitaet Stuttgart, Germany. Ceramics ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1. Investigations were performed on superalloy single crystals based Ni which were ...
Development of a collision energy absorber of a passenger train
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Development of shock absorbers is one of the necessary measures for passive protection of passenger coaches. The purpose of passive protection is to minimize the collision consequences for passengers. Present solutions are ...
The influence of the solidification rate on the interface shape and distribution of solute
(Savez inženjera metalurgije Srbije, Beograd, 2002)
In this paper investigation of the influence of the solidification conditions on the interface shape and distribution of solute during the solidification of AI-Cu alloy by vertical Bridgman method were investigated. The ...
On the Al-Mg alloy sheets for automotive application: Problems and solutions
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Aluminium alloys suitable for automotive application were reviewed briefly as well as the reasons for the future wider application of Al-Mg type alloys. Basic problems related to the limited consumption of Al-Mg type alloy ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...