Претраживање
Приказ резултата 11-20 од 178
Strength design calculation of a horizontal pressure vessel / Kontrolni proračun čvrstoće horizontalne posude pod pritiskom
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
Standards SRPS M.E2.250-262 for calculation of pres-sure vessels have been replaced by SRPS EN 13445-3. This means that calculations of new equipment and check calculations of equipment in service are subjected to ordinance ...
Microstructure evolution and mechanical properties degradation of HPNB alloy after an eleven-year service / Mikrostrukturni razvoj i degradacija mehaničkih svojstava legure HPNB posle jedanaest godina eksploatacije
(Society for Structural Integrity and Life (DIVK), 2022)
In this work, the heat-resistant cast steel HP40Nb alloy, produced in the form of a centrifugally cast tube, which failed after 11.4 years service is investigated. The microstructure is examined using a scanning electron ...
New types of protective coatings and development of test methods / Nove vrste zaštitnih premaza i razvoj metoda ispitivanja
(Society for Structural Integrity and Life (DIVK), 2023)
The paper presents the results of synthesis and characterisation of refractory coatings based on various fillers
intended for the protection of metallic structures. Refractory
fillers applied are based on mullite, ...
Effect of the pH of artificial saliva on ion release from commercially pure titanium / Uticaj pH vrednosti veštačke pljuvačke na otpuštanje jona iz komercijalno čistog titana
(Faculty of Technology, Novi Sad, 2013)
Due to their excellent characteristics, such as chemical inertness, mechanical resistance, low Young's modulus, high corrosion resistance, and outstanding biocompatibility, titanium and its alloys are the most used metallic ...
Integrity assessment of regulation system pipeline elements in hydroelectric generating set a6 of hydro power plant 'Djerdap 1'
(Society for Structural Integrity and Life, Institute for Material Testing, 2016)
Vertical Kaplan turbines with nominal power of 176 MW manufactured in Russia are installed in 6 hydroelectric generating sets at hydro power plant 'Djerdap 1' (Kladovo, Serbia). Most of the components are made of materials ...
Influence of working conditions on strength calculation of pressure vessel of austenitic steel according to SRPS EN 13445 / Uticaj radnih uslova na proračun čvrstoće posude pod pritiskom od austenitnog čelika prema SRPS EN 13445
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
Upon the adoption of regulations for pressure equipment the series of standards SRPS EN 13445 began to apply. The paper illustrates strength calculation of a vertical cylindrical pressure vessel of austenitic steels according ...
Complex sulphide-barite ore leaching in ferric chloride solution
(Association of Metallurgical Engineers of Serbia, 2016)
The results of research on the leaching process of complex sulphide-barite ore were presented in this paper. The leaching process was carried out in a laboratory autoclave by ferric chloride solution. Considering that those ...
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
Influence of Cr, Mn and Mo on structure and properties of V microalloyed medium carbon forging steels
(Savez inženjera metalurgije Srbije, Beograd, 2010)
The influence of Cr, Mo and Mn on microstructure and mechanical properties of V-microalloyed medium-carbon steels has been studied by means of metallography and mechanical testing. Cr, Mn and Mo addition promotes the ...