Претраживање
Приказ резултата 1-10 од 25
Cavitation resistance of the material PA 3200 GF produced by selective laser sintering
(International Institute for the Science of Sintering (IISS), 2023)
The present study focuses on the results of cavitation resistance research of samples obtained by the Selective Laser Sintering technology. The samples were made from polyamide powder reinforced with glass beads – PA 3200 ...
The Thermophysical Properties of Primary Phase in Lithium Germanium Phosphate Glass
(Science of Sintering, 2021)
The selected lithium germanium-phosphate glass was prepared by a conventional melt-quenching technique. The XRD method was employed to confirm the glass was obtained and to reveal crystalline phases during heat treatment. ...
Evolution of Structural and Functional Properties of the Fe/BaTiO3 System Guided by Mechanochemical and Thermal Treatment
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
Multiferroic systems are attractive to the researches worldwide due to diversity of existing applications, as well as possible novel ones. In order to contribute to understanding of the processes that take place within the ...
Adsorption of Anthraquinone Dye AB111 from Aqueous Solution using Synthesized Alumina-Iron Oxide Doped Particles
(Science of Sintering, 2021)
Adsorption of anthraquinone dye Acid Blue 111 by alumina-iron oxide doped particles prepared by sol-gel method from aqueous solutions was studied. The adsorbent morphology was revealed by FESEM and the crystallographic ...
The Effect of the Concentration of Alkaline Activator and Aging Time on the Structure of Metakaolin Based Geopolymer
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
This paper outlines the production of an inorganic polymer/geopolymer using a metakaolin by an environmental friendly, energy saving, clean technology to conserve natural environment and resources. The influence of alkali ...
Basalt-Polyester Hybrid Composite Materials for Demanding Wear Applications
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer ...
Cavitation Properties of Rendering Mortars with Micro Silica Addition
(Science of Sintering, 2021)
Micro-silica is a highly efficient mineral additive whose role is reflected in improvements of microstructure packing, strength and durability of non-shaped composite building materials such as concrete and mortar. A ...
Evaluation of Adsorption Performance and Quantum Chemical Modeling of Pesticides Removal using Cell-MG Hybrid Adsorbent
(Science of Sintering, 2021)
Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, ...
Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent
(International Institute for the Science of Sintering (IISS), 2022)
In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were ...
The crystal growth of NASICON phase from the lithium germanium phosphate glass
(International Institute for the Science of Sintering, 2023)
The crystal growth rate of LiGe2(PO4)3 phase from lithium germanium-phosphate glass was studied. The glass have been homogenized using the previously established temperature-time conditions, which make it possible to remove ...