Претраживање
Приказ резултата 1-10 од 166
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
Chemical durability of sintered glass-composite prepared from glass cullet and waste foundry sand
(Metallurgical & Materials Engineering, 2021)
In this study, the glass-composite was prepared using glass cullet and waste foundry sand as raw materials. The powder technology route was employed. The mixtures containing 10-50 wt% of the sand were sintered at T = 750 ...
Nanostructured intrinsically conducting polymers formed by electrochemical synthesis / Nanostruktuirani elektroprovodni polimeri dobijeni elektrohemijskom sintezom
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Due to unique properties of intrinsically conducting polymers (ICP) such as: electrical conductivity, reversible electrochemistry, optical activity, biocompatibility, environmental and corrosion stability, they still ...
The effect of mould temperature and cooling conditions on the size of secondary dendrite arm spacing in Al-7Si-3Cu alloy
(Savez inženjera metalurgije Srbije, Beograd, 2009)
The secondary dendrite arm spacing (SDAS) is one of the most important microstructure features of as-cast structure in hypoeutectic aluminum alloys. The size of SDAS depends on many factors such as liquid metal treatment, ...
Effect of heating rate on precipitation of peak-aged Al-Li (8091) alloy: A quantitative approach
(Savez inženjera metalurgije Srbije, Beograd, 2010)
Samples of Al-Li (8091) alloy were solution treated at 540ºC for 30 min, water-quenched and continuously heated in oil at 0.05 and 0.1ºC/min rates, from room temperature to 190ºC when the peak hardness was achieved. Having ...
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Vrednovanje intelektualne svojine
(Economics institute, Belgrade, 2011)
Intellectual Property Rights (IPRs) and Intangible Assets (IAs) can be highly valuable playing a key role in many fields of business, touching nearly all aspects of a company: products development, human capital, marketing ...
Modern steels: Transformation induced plasticity / Savremeni čelici - transformacijom izazvana plastičnost
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2011)
TRIP čelici danas zauzimaju značajno mesto u komercijaloj upotrebi u vozilima i konstrukcijama kod kojih je jedan od glavnih zahteva redukcija sopstvene težine. Optimalna kombinacija udela stabilisanog austenita i stepen ...
Structural properties of Co, Ni and Mo powders obtained by electrochemical deposition
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Magnetic thin films based on iron group elements (Fe, Co, Ni) are currently used in computer's hard disk drives and in MEMS, whereas electrodeposition is a suitable method to obtain these materials. The powders of metals ...