Претраживање
Приказ резултата 1-10 од 57
Structural characteristics of some ternary Ag-In-Sn alloys
(Savez inženjera metalurgije Srbije, Beograd, 2008)
The Ag-In-Sn system, as one of potential lead-free solder materials, was studied in this paper. The investigated alloys were chosen from two sections, with molar ratio of In:Sn equal to 1:4; 1:2. DTA, XRD, SEM and micro ...
The effect of heat treatment on toughness and wear resistance of Fe-Cr-C-Nb alloys / Uticaj termičke obrade na žilavost i otpornost na habanje Fe-Cr-C-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Alloying with niobium improves the mechanical properties of the high chromium irons. The alloy containing appriximately 3 %Nb gives the best compromise between wear resistance and toughness. These properties were improved ...
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheet
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheets was examined after cold rolling and annealing in the range of temperature from 220°C to 520°C, water quenching and natural aging. The low temperature annealed ...
Image analysis of protective layer of zinc on steel obtained using the hot process / Analiza slike za karakterisanje zaštitnog sloja cinka na čeliku dobijenog toplim cinkovanjem
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The procedure for measuring the thickness of anticorrosion protective layer of zinc on steel is given. The metallographic images are used for this measurement. Results are statistically handled and results are used to ...
The influence of the solidification rate on the interface shape and distribution of solute
(Savez inženjera metalurgije Srbije, Beograd, 2002)
In this paper investigation of the influence of the solidification conditions on the interface shape and distribution of solute during the solidification of AI-Cu alloy by vertical Bridgman method were investigated. The ...
On the Al-Mg alloy sheets for automotive application: Problems and solutions
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Aluminium alloys suitable for automotive application were reviewed briefly as well as the reasons for the future wider application of Al-Mg type alloys. Basic problems related to the limited consumption of Al-Mg type alloy ...
The influence of the interface shape on the plane-to-cellular-to-dendritic transition in superalloy based of nickel
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper investigation of the influence of the crystallization conditions on the interface shape during the solidification of Ni-based Superalloy by Vertical Bridgman method were investigated. The samples were undertaken ...
Application of instrumental methods in the investigation of properties and microstructure of construction concretes / Primena instrumentalnih metoda za ispitivanje svojstava i mikrostrukture konstukcionih betona
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Methods for the investigation of microstructure of construction concretes are presented in this paper. Concrete is a composite material, thus its microstructure consists of bonding agent (cement) and aggregate with predefined ...
Influence of heat transfer conditions on determination of thermal shock resistance of refractories / Uticaj prenosa toplote na određivanje termostabilnosti vatrostalnog materijala
(Savez inženjera metalurgije Srbije, Beograd, 2002)
The goal of this thesis was to determine the thermal shock resistance of alumina based refractories in the case of a heat transfer conditions different from the standard conditions given by quenching test JUS. B. D.8 319. ...
Kinetics of crystallization silicon-(IV)-nitride / Kinetika kristalizacije silicijum-(IV)-nitrida
(Savez inženjera metalurgije Srbije, Beograd, 2003)
Amorphous covalent Si-C-N ceramics have been synthesized by pyrolysis polysilazanes. This part of experiment was done in Institute für Nichtmetallische Anorganische Materialien, Universitaet Stuttgart, Germany. Ceramics ...