Претраживање
Приказ резултата 31-40 од 57
Zn-Co-CeO2 vs. Zn-Co Coatings: Effect of CeO2 Sol in the Enhancement of the Corrosion Performance of Electrodeposited Composite Coatings
(Metals, 2021)
Electrodeposition and characterization of novel ceria-doped Zn-Co composite coatings was the main goal of this research. Electrodeposited composite coatings were compared to pure Zn-Co coatings obtained under the same ...
Enhanced Interface Adhesion by Novel Eco-Epoxy Adhesives Based on the Modified Tannic Acid on Al and CFRP Adherends
(MDPI, Basel, 2020)
This paper presents a new process for obtaining eco-epoxide adhesives synthesized from bio-renewable raw material (tannic acid-TA) and used for bonding lightweight materials (aluminum (Al) and carbon fiber reinforced polymer ...
Ecological Risk Assessment of Heavy Metals in the Soil at a Former Painting Industry Facility
(Frontiers Media Sa, Lausanne, 2020)
Soil samples from the site of the former largest paint and varnish factory in ex-Yugoslavia were analyzed for arsenic and eight heavy metals (Pb, Cd, Zn, Cr, Ni, Cu, Fe, and Hg). Several additional soil properties (pH, ...
Dextran-Based Edible Coatings to Prolong the Shelf Life of Blueberries
(Polymers, 2021)
The development of edible films and coatings in the food packaging industry presents one of the modern strategies for protecting food products and ensuring their freshness and quality during their shelf lives. The application ...
Tailored Adhesion Properties of Acrylate Adhesives on Al Alloys by the Addition of Mn-Al-LDH
(Polymers, 2021)
The goal of this study was to investigate the effect of the structure of Mn-Al layered double hydroxide (LDH) on the adhesion behavior of composite adhesives on two Al alloys (L3005 and L8079). The composite adhesives were ...
Influence of Electrolyte Impurities from E-Waste Electrorefining on Copper Extraction Recovery
(Metals, 2021)
In order to reflect possible issues in future sole e-waste processing, an electrolyte of complex chemical composition reflecting system of sole e-waste processing was obtained by following a specially designed pyro-elect ...
Non-woven sorbent based on recycled jute fibers for efficient oil spill clean-up: From production to biodegradation
(Elsevier B.V., 2023)
Loose assemblies of cellulose fibers could be employed in the clean-up of oil spills, but the difficulty to separate them from the spill after use makes them impractical. In an effort to tackle this issue, a non-woven ...
Application of the Flotation Tailings as an Alternative Material for an Acid Mine Drainage Remediation: A Case Study of the Extremely Acidic Lake Robule (Serbia)
(MDPI, Basel, 2020)
Flotation tailings rich in carbonate minerals from the tailings deposit of the copper mine Majdanpek (Serbia) were applied for neutralization of the water taken from the extremely acidic Lake Robule (Bor, Serbia). Tests ...
Electrophoretic Deposition of Biocompatible and Bioactive Hydroxyapatite-Based Coatings on Titanium
(Materials, 2021)
Current trends in biomaterials science address the issue of integrating artificial materials as orthopedic or dental implants with biological materials, e.g., patients' bone tissue. Problems arise due to the simple fact ...
The effect of modified tannic acid (TA) eco-epoxy adhesives on mode I fracture toughness of bonded joints
(Polymer Testing, 2021)
Two synthesized eco-epoxy components based on TA: (A) glycidyl ether and (B) glycidyl phosphate ester, are used, as a replacement for the Bisphenol A (BPA) based epoxy component, for bonding aluminum (Al) and carbon fiber ...