Претраживање
Приказ резултата 31-40 од 43
Preparation and Characterization of Novel Glycidyl Methacrylate/Clay Nanocomposites
(Science of SinteringScience of Sintering, 2022)
The impact of the type and amounts of nanofiller on the features of the glycidyl methacrylate-co-ethylene glycol dimethacrylate (GMA-co-EGDMA)/organomodified montmorillonite (OMt) nanocomposites that were prepared by in ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
The Influence of Powder Particle Size on Properties of Cu-Al2O3 Composites
(International Institute for the Science of Sintering (IISS), 2009)
Inert gas atomized prealloyed copper powder containing 2 wt.% Al (average particle size approximate to 30 mu m) and a mixture consisting of copper (average particle sizes approximate to 15 mu m and 30 mu m) and 4 wt.% of ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass
(Science of Sintering, 2022)
The nucleation process of lithium germanium-phosphate glass was studied to determine the temperature range of nucleation and the temperature of the maximum nucleation rate. The differential thermal analysis (DTA), and ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
The Mechanisms of Cavitation Erosion of Raw and Sintered Basalt
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
The paper analyzes the morphology of cavitation damage of raw and sintered basalt samples. The experiment was conducted using the ultrasonic vibratory cavitation test method according to the ASTM G-32 standard. During the ...
Analysis of the properties of a Cu-Al2-O3 sintered system based on ultra fine and nanocomposite powders
(International Institute for the Science of Sintering, Beograd, 2007)
In this paper synthesis of a composite based on Cu-Al2O3 by a thermo-chemical method is shown along with a comparative analysis of the properties of the obtained nanocomposite sintered samples, which are characterized by ...
Synthesis of Anatase Nanopowders by Sol-gel Method and Influence of Temperatures of Calcination to Their Photocatalitic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The titanium dioxide (TiO2) nanopowders were produced by sol-gel technique from tetrabutyl titanate as a precursor, varying the temperature of calcination (from 500 to 550 degrees C with the step of 10 degrees C). XRPD ...
The crystal growth of NASICON phase from the lithium germanium phosphate glass
(International Institute for the Science of Sintering, 2023)
The crystal growth rate of LiGe2(PO4)3 phase from lithium germanium-phosphate glass was studied. The glass have been homogenized using the previously established temperature-time conditions, which make it possible to remove ...