Претраживање
Приказ резултата 11-20 од 30
Some aspects of physical metallurgy of microalloyed steels
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Some aspects of deformation, precipitation, and recrystallization behavior in medium carbon V-microalloyed and low carbon Nb/Ti-microalloyed steels are presented in the paper. Changes in microstructure are explained together ...
Kinetics of barite reduction from refractory barite-sulphide ore
(Savez inženjera metalurgije Srbije, Beograd, 2016)
Refractory sulphide-barite ore was reduced with carbon in order to release lead, zinc, and copper sulphide from barite-pyrite base. Mineralogical investigations showed that due to the complex structural-textural relationships ...
Influence of the fabrication process of copper matrix composites on cavitation erosion resistance
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
Defect formation during synthesis and welding of silver nanowires for solar cell applications
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Structural defects such as stacking faults and twins, observed in many face-centered cubic (FCC) structured metals and alloys with low stacking fault energies, in general, play an important role in microstructure evolution, ...
The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys
(Savez inženjera metalurgije Srbije, Beograd, 2019)
The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical ...
Synthesis of novel wo3/zrsio4 catalysts for dehalogenation of halogenated hydrocarbons
(Savez inženjera metalurgije Srbije, Beograd, 2019)
This research aimed to develop a novel catalyst based on WO3/ZrSiO4 system for halogenated hydrocarbons processing. The production method of this catalyst involved extrusion and as such was simplified compared to thermo-chemical ...
Synthesis of nife2o4 nanofibers by joint sol-gel and electrospinning technique
(Savez inženjera metalurgije Srbije, Beograd, 2018)
In this study, electrospinning combined with sol-gel technique is applied in order to produce magnetic nickel ferrite (Ni-ferrite) nanofibers. The prepared Ni-ferrite gel was mixed with poly(vinylpyrrolidone) (PVP) solution ...