Pretraživanje
Prikaz rezultata 1-10 od 58
The effect of heat treatment on toughness and wear resistance of Fe-Cr-C-Nb alloys / Uticaj termičke obrade na žilavost i otpornost na habanje Fe-Cr-C-Nb legura
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Alloying with niobium improves the mechanical properties of the high chromium irons. The alloy containing appriximately 3 %Nb gives the best compromise between wear resistance and toughness. These properties were improved ...
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheet
(Savez inženjera metalurgije Srbije, Beograd, 2005)
Deformation behavior of the AlMg4.5Cu0.5 type alloy sheets was examined after cold rolling and annealing in the range of temperature from 220°C to 520°C, water quenching and natural aging. The low temperature annealed ...
The influence of thermomechanical treatment and chemical composition on recrystallization of Al-Mg alloys
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behaviour of AlMg3, AlMg4.5Mn and AlMg6Mn alloy plates subjected to different thermomechanical treatments (TMTs), has been studied by means of optical microscopy and hardness measurements. Applied two-stage ...
Application of instrumental methods in the investigation of properties and microstructure of construction concretes / Primena instrumentalnih metoda za ispitivanje svojstava i mikrostrukture konstukcionih betona
(Savez inženjera metalurgije Srbije, Beograd, 2008)
Methods for the investigation of microstructure of construction concretes are presented in this paper. Concrete is a composite material, thus its microstructure consists of bonding agent (cement) and aggregate with predefined ...
Experimental design approach regarding kinetics of high pressure leaching processes / Dizajniranje eksperimenata u pogledu na kinetiku luženja pri visokim pritiscima
(Savez inženjera metalurgije Srbije, Beograd, 2003)
Kinetics of high pressure leaching of nickel latente ore "Rudjinci", Serbia was studied in this work. The following parameters: temperature, acid to ore ratio, stirring speed, and time were optimized in order to obtain the ...
Studies of a wear resistant cast iron / Izučavanje belih gvožđa otpornih na habanje
(Savez inženjera metalurgije Srbije, Beograd, 2003)
The objective of this investigation was to set down (on the base of the results obtained by the examination of white cast iron alloys with different content of the alloying elements) a correlation between chemical composition ...
Influence of vanadium content and colling rate on the stereological parameters of phases in the structure of Fe-C-Cr-V alloys / Uticaj sadržaja vanadijuma i brzine hlađenja na stereološke parametre faza u strukturi Fe-C-Cr-V legura
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper, the influence of vanadium content and cooling rate on the stereological parameters of phases present in the structure of Fe-C-Cr-V alloys. Experimental results indicate that both vanadium content and cooling ...
Approximation of material behaviour of PLLA polymer in HAp/PLLA biocomposite material using nanoindentation and finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2007)
In this work, a combination of nanoindentation experiment and finite element modeling is proposed in order to obtain approximate material behavior of PLLA polymer in hydroxyapatite (HAp)/poly-L-lactide (PLLA) composite. ...
Rotating disk alumina precursor fiber formation process stability determination using image analysis
(Savez inženjera metalurgije Srbije, Beograd, 2002)
Precursor fibers are made from the aluminium-hydroxide chloride based sols. The process stability can be influenced both by the fiber formation conditions and the rheology of the sol. The distance from the disk canter is ...
The influence of the cellular structure of the seed on the structure single crystal superalloy based on Ni / Uticaj ćelijske strukture klice na strukturu monokristala superlegure na bazi Ni
(Savez inženjera metalurgije Srbije, Beograd, 2003)
This paper elaborates the investigations about influence of the cellular structure of the seed to the distance between primary dendrites, λ1. Investigations were performed on superalloy single crystals based Ni which were ...