Претраживање
Приказ резултата 11-20 од 73
Experimental and numerical evaluation of a steamline behaviour using local approach
(Croatian Metallurgical Society, 2007)
Results of the experimental and numerical comparative analysis of steamline pipes have been presented. New pipes and the pipes used for more than 117,000 hours at 540 degrees C under pressure of 42 bars have been simultaneously ...
A model for predicting fracture toughness in overaged 7000 alloy forgings
(Savez inženjera metalurgije Srbije, Beograd, 2007)
An attempt to develop a multiple micromechanism-based model for predicting plane-strain fracture toughness, KIc, of overaged 7000 alloy forgings has been made. The proposed model reveals the quantitative relations between ...
Synthesis and sintering of Cu-Al2O3 nanocomposite powders produced by a thermochemical route
(Savez inženjera metalurgije Srbije, Beograd, 2007)
By hydrometallurgy and powder metallurgy along with prognosis of physical-chemical properties, a synthesis of new improved materials can be successfully performed with in advance pre-set properties which is conditioned by ...
Investigation of mechanism and kinetics of chalcopyrite concentrate oxidation process
(Croatian Metallurgical Society, 2008)
The oxidation process of chalcopyrite concentrate "Rudnik" (Serbia) was investigated by DTA-TG measurements under air conditions in the temperature range of 298 - 1173 K, as well as by XRD analysis of the oxidation products ...
Development of contemporary procedures for lead obtaining / Razvoj savremenih postupaka dobijanja olova
(Savez inženjera metalurgije Srbije, Beograd, 2004)
Contemporary procedures of lead concentrates treatment were in different expansion during last thirty years. All procedures have in common the following: smelting reaction proceeds in solid-gas suspension, melting products ...
Tensile properties of fiber-resin composites that consist of polyarmid fiber (Kevlar 129) and poly(vinilbutyral) / Zatezna svojstva polimernog kompozitnog materijala poliaramidna vlakna (Kevlar 129) - poli(vinilbutiral)(PVB)
(Savez inženjera metalurgije Srbije, Beograd, 2006)
Thanks to fact that composite material have usefully characteristic two or more materials, they are becoming more and more substitute standard materials in every field of technique they start to. In this study static ...
Hydrometallurgical recovery of tin and lead from waste printed circuit boards (wpcbs): limitations and opportunities
(Croatian Metallurgical Soc, Zagreb, 2016)
In this paper, possibility for selective Pb and Sn recovery, using three different solutions of NaOH, HCl and HNO3, from WPCBs containing low concentrations of Pb and Sn is presented. According to obtained results, over ...
A two-stage metal valorisation process from electric arc furnace dust (eafd)
(Croatian Metallurgical Soc, Zagreb, 2016)
This paper demonstrates possibility of separate zinc and lead recovery from coal composite pellets, composed of EAFD with other synergetic iron-bearing wastes and by-products (mill scale, pyrite-cinder, magnetite concentrate), ...
The influence of thermomechanical treatment on recrystallization of AlMg4.5Cu0.5 alloy
(Savez inženjera metalurgije Srbije, Beograd, 2007)
Recrystallization behavior of an Al-Mg-Cu alloy (4.5 wt. %Mg and 0.45 wt %Cu) subjected to different thermomechanical treatments (TMTs) have been studied by means of light optical microscopy and hardness measurements. In ...
The recycling of high magnesium aluminum alloys estimation of the most reliable procedure
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Aluminum is one of the most recyclable materials. Namely, the properties of aluminum are not affected by the recycling and reuse, thus enable that high value of the metal is maintained after reprocessing. The re-smelting ...