Претраживање
Приказ резултата 11-20 од 69
Influence of heat treatment on mechanical and sorptional properties of viscose-based nonwovens
(Niscair, 2005)
The influence of heat treatment on sorptional and mechanical properties of viscose: polypropylene (90:10) blend nonwoven fleeces has been studied. It is observed that the heat treatment improves mechanical properties ...
Development and characterization of thermosensitive hydrogels based on poly(N-isopropylacrylamide) and calcium alginate
(Wiley, Hoboken, 2012)
This work refers to the synthesis and characterization of thermosensitive hydrogels based on interpenetrating polymer networks (IPNs) of poly(N-isopropylacrylamide) (PNIPAAm) and calcium alginate in the form of films. The ...
Improvement of the mechanical properties of spark plasma sintered hap bioceramics by decreasing the grain size and by adding multi-walled carbon nanotubes
(International Institute for the Science of Sintering, Beograd, 2013)
Composites based on HAP and oxidized multi-walled carbon nanotubes (o-MWCNT) and monophase HAP materials were processed by spark plasma sintering. Starting from stoichiometric nano-sized HAP powder, monophase bioceramics ...
Cavitation resistance of composite polyester resin/basalt powder
(Society for Structural Integrity and Life, Institute for Material Testing, 2019)
The paper presents the results of research on cavitation resistance of the composite based on unsaturated polyester resin and basalt powder, as reinforcement. Basalt powder was obtained by grinding and micronising basaltic ...
Poly[(N-isopropylacrylamide)-co-(itaconic acid)] hydrogels with poly(ethylene glycol)
(Wiley, Hoboken, 2010)
The aim of the work reported here was to investigate temperature- and pH-sensitive hydrogels of N-isopropylacrylamide (NIPAM) and itaconic acid (IA) and their semi-interpenetrating polymer networks (semi-IPNs) with varying ...
Dynamic mechanical properties of aramid fabrics impregnated with multiwalled carbon nanotubes / Dinamičko mehanička svojstva aramidnih lamina impregnisanih sa višeslojnim ugljeničnim nanocevima
(Engineering Society for Corrosion, Belgrade, Serbia, 2013)
Carbon nanotubes (CNT) represent allotropes of carbon with a cylindrical nanostructure. In multiwalled carbon nanotubes (MWCNT), graphitic layers make up concentric tubes. The multiwalled nanotubes length in our research ...
Mechanical properties correlation to processing parameters for advanced alumina based refractories
(International Institute for the Science of Sintering, Beograd, 2012)
Alumina based refractories are usually used in metallurgical furnaces and their thermal shock resistance is of great importance. In order to improve thermal shock resistance and mechanical properties of alumina based ...
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (hsla) steel on low cycle fatigue
(Croatian Metallurgical Soc, Zagreb, 2014)
High strength low-alloy steel under low cycle fatigue at a certain level of strain controlled achieve stabilized condition. During the fatigue loading stabilized hysteresis loop is determined, which typical cycle of ...
Effect of surface modified TiO2 nanoparticles on thermal, barrier and mechanical properties of long oil alkyd resin-based coatings
(Budapest Univ Technol & Econ, Budapest, 2015)
Novel soy alkyd-based nanocomposites (NCs) were prepared using TiO2 nanoparticles (NPs) surface modified with different gallates, and for the first time with imine obtained from 3,4-dihydroxybenzaldehyde and oleylamine ...
The effect of friction stirs welding speed on microstructure, mechanical properties and IGC of EN AW-5083 plates
(Advanced Technologies and Materials, 2019)
The aim of this work was to evaluate the influence of welding speed on microstructure, mechanical properties, as well as Intergranular corrosion (IGC) susceptibility of EN AW-5083 alloy welded using FSW. FSW was performed ...