Претраживање
Приказ резултата 11-20 од 166
The effect of salinity on the sorption of cadmium ions from aqueous medium on Fe(III)-sepiolite / Uticaj saliniteta vode na sorpciju jona kadmijuma na Fe(III)-sepiolitu
(Association of the Chemical Engineers of Serbia, 2015)
In this study, the sorption of cadmium ions onto sepiolite modified with hydrated iron(III) oxide, Fe(III)-sepiolite, has been investigated in natural seawater, artificial seawater, aqueous solution of NaCl of the same ...
Metallurgical processing of copper secondary raw materials / Metalurška prerada sekundarnih sirovina bakra
(Savez inženjera i tehničara Srbije, Beograd, 2015)
Procedures for copper secondary raw materials processing include two basic stages: pretreatment of the copper waste and its further metallurgical processing. For copper waste pretreatment technology, there are different ...
The influence of membrane composition on the release of polyphenols from liposomes / Uticaj sastava membrane na brzinu otpuštanja polifenola iz lipidnih mikročestica
(Association of Chemical Engineers of Serbia, 2015)
Polyphenols are compounds which are widely studied due to their antioxidative and potential therapeutic properties. Systems for the controlled release of drugs offer a number of benefits comparing with traditional forms ...
Optimization of chitosan gel preparation for supercritical impregnation of thymol / Uticaj pripreme hitozan gelova na natkritičnu impregnaciju sa timolom
(Savez inženjera i tehničara Srbije, Beograd, 2015)
The impregnation of differently prepared chitosan gels with thymol using supercritical carbon dioxide (scCO2) was studied in order to obtain new materials with added value without the use of organic solvents. The optimum ...
Calculation and optimization of the copper (II) sulphate monohydrate from copper (II) sulphate pentahydrate production process in a fluidized bed dryer / Proračun i optimizacija procesa proizvodnje bakar(II)-sulfat-monohidrata iz bakar(II)-sulfat-pentahidrata u sušnicama sa fluidizovanim slojem
(Association of Chemical Engineers of Serbia, 2015)
In this paper the process of the copper (II) sulphate monohydrate from copper (II) sulphate pentahydrate (also known as a Blue vitriol or Bluestone) production was analyzed. Copper (II) sulphate pentahydrate is one of the ...
Synthesis and performance of polymer based magnetic composite sensing element
(Inst Materials Physics, Bucharest, 2015)
The commercial multi-mode optical fiber was coated with magnetic composite material prepared using Nd-Fe-B permanent magnet powder dispersed in poly (ethylene-co-vinyl acetate)-EVA. Characterization of microstructure, ...
A method for determination of separation properties of membranes / Metod za određivanje separacionih svojstava membrana
(Bosnia and Herzegovina : University of East Sarajevo, Faculty of Technology, 2015)
In this study, design of lab scale device for determination of separation properties of membranes is presented and analyzed. Device operates with different gas pressure between chambers, whereby gas streams perpendicular ...
Formic acid electrooxidation on carbon supported platinum catalyst with preferential plane orientation / Oksidacija mravlje kiseline na platinskim katalizatorima na ugljeničnom nosaču sa preferencijalno orijentisanim ravnima
(Savez inženjera i tehničara Srbije, Beograd, 2015)
Pt-based nanocatalysts supported on Vulcan XC-72R carbon, were prepared by water-in-oil microemulsion method, with addition of various amounts of HCl in the water phase. Polyethileneglycoldodecylether (BRIJ 30) was used ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...
Influence of pin geometry on mechanical and structural properties of butt friction stir welded 2024-T351 aluminum alloy / Uticaj geometrije trna alata na mehaničke i strukturne karakteristike sučeonog spoja aluminijumske legure 2024-T351 zavarenog postupkom FSW
(Association of Chemical Engineers of Serbia, 2015)
The aim of this work was to investigate the combined effect of small difference in pin geometry, together with rotation and welding speed on the weldability, mechanical and structural properties of FSW 2024-T351 Al plates. ...