Претраживање
Приказ резултата 61-70 од 174
The influence of light on corrosion of polyaniline coated mild steel / Uticaj osvetljenosti na koroziju mekog čelika sa prevlakom polianilina
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
The influence of light of the mild steel corrosion in 3% NaCl solution with polyaniline coating based on the possibilities that polyaniline can generate photoelectrons, even in the laboratory conditions has been investigated.
Preservation of vitamin C, lycopene and carbohydrate content in tomato dried in a tunnel type dryer / Očuvanje vitamina C, likopena i ugljenih hidrata u plodovima paradajza sušenim u tunelskom tipu sušara
(Institute for Food Technology, Novi Sad, 2017)
The aim of this study was to find an optimal way of tomato drying in a tunnel type dryer, in order to achieve the lowest possible losses in nutritive value of dried tomato products. Domestic variety of tomato (SP-109) was ...
Micromechanical crack analysis of glass-epoxy laminated composites subjected to tension load / Mikromehanička analiza loma laminatnog staklo-epoksi kompozitnog materijala ispitivanog na zatezanje
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The main objective of this study is to determine tensile properties of the glass-epoxy polymer composite material. The material is glass fiber 280 g/m², 'twill woven' with 100 cm width, type - Interglas 92125, and epoxy ...
Polymer-Based Smart Coatings for Comfort in Clothing
(University of Ljubljani, Fac Natural Sci & Engineering, Dept Textiles, Ljubljana, 2016)
This paper reviews the application of polymer-based smart coatings for obtaining active comfort regulation in clothing. Currently available systems for adaptive comfort regulation which involve application of phase change ...
Significance and applicability of structural integrity assessment / Značaj i primenljivost ocene integriteta konstrukcija
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
To avoid unexpected and frequent serious failures of objects and equipment in service, and save their structural integrity, proper experimental and theoretical analyses are required, that are supported by modeling and ...
Techno-economic analysis of unsaturated polyester production from waste PET / Tehno-ekonomska analiza proizvodnje nezasićenih poliestara iz otpadnog PET-a
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Unsaturated polyester resins (UPe) were synthesized from maleic anhydride and products of glycolysis, obtained by polyethylene terephthalate (PET) depolymerization with dipropylene glycol (DPG) in the presence of tetrabutyl ...
Defect formation during synthesis and welding of silver nanowires for solar cell applications
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Structural defects such as stacking faults and twins, observed in many face-centered cubic (FCC) structured metals and alloys with low stacking fault energies, in general, play an important role in microstructure evolution, ...
Influence of the Fe(III): Modified clinoptilolite on phosphorus leaching from different soil types / Uticaj Fe(III)- modifikovanog klinoptilolita na izluživanje fosfora iz različitih vrsta zemljišta
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Influence of the iron(III)-modified clinoptilolite (FeCLI) on phosphorus leaching from two different Norwegian soil types (sand and clay loam soil) was studied using a column system at room temperature. FeCLI was used in ...
Modelling of Dyeing of Modified Polyester at Lower Temperature by Ultrasound
(University of Ljubljani, Fac Natural Sci & Engineering, Dept Textiles, Ljubljana, 2018)
This article discusses the process of polyester dyeing through the modelling process, i.e. the ability of adsorption of dyes for chemically modified polyester fibres of knitted fabrics in aqueous environment in the presence ...
The effect of friction stirs welding speed on microstructure, mechanical properties and IGC of EN AW-5083 plates
(Advanced Technologies and Materials, 2019)
The aim of this work was to evaluate the influence of welding speed on microstructure, mechanical properties, as well as Intergranular corrosion (IGC) susceptibility of EN AW-5083 alloy welded using FSW. FSW was performed ...