Претраживање
Приказ резултата 61-70 од 312
Possibilities of utilization of co-products from corn grain ethanol and starch production / Mogućnosti iskorišćenja sporednih proizvoda prerade kukuruznog zrna iz proizvodnje etanola i skroba
(Association of Chemical Engineers of Serbia, 2013)
In recent decades, the expansion of alternative fuels production from crops traditionally used for food and animal feed has led to significant changes in the field of energy production, agriculture and food industry. Starch ...
Optimization of (-galactosidase production from lactic acid bacteria / Optimizacija proizvodnje (-galaktozidaze pomoću bakterija mlečne kiseline
(Association of Chemical Engineers of Serbia, 2015)
(-galactosidase, commonly known as lactase, represents commercially important enzyme that is prevalently used for lactose hydrolysis in milk and whey. To the date, it has been isolated from various sources. In this study ...
Alkyl polyglucoside-stabilized emulsion as a prospective vehicle for usnea barbata CO2-supercritical extract: Assessing stability, safety and efficiency of a topical formulation / Emulzija stabilizovana alkil poliglukozidnim emulgatorom kao potencijalni nosač za CO2-natkritični ekstrakt vrste Usnea barbata - procena stabilnosti, bezbednosti i efikasnosti topikalne formulacije
(Association of Chemical Engineers of Serbia, 2015)
Antimicrobial activity of Usnea barbata especially against bacteria involved in pathogenesis of various skin conditions has been well documented in literature. Nevertheless, there are no papers dealing with formulation of ...
Guidelines for general adsorption kinetics modeling
(Savez hemijskih inženjera, Beograd, 2020)
Adsorption processes are widely used in different technological areas and industry sectors, thus continuously attracting attention in the scientific research and publications. Design and scale-up of these processes are ...
Optimization of spray drying conditions for production of Achillea millefolium extract powder
(Hemijska industrija, 2021)
In this study, a spray drying process of yarrow (Achillea millefolium L.) liquid extracts was optimized by using the response surface methodology. The study aimed to determine the influence of temperature (120-195 degrees ...
Effects of structural and textural grain characteristics on leaching of sulphide minerals from a polymetallic concentrate by sodium nitrate and sulphuric acid solution
(Savez hemijskih inženjera, Beograd, 2017)
In this paper, the influence of structural and textural characteristics of sulfide minerals on their leaching from a polymetallic concentrate by sulfuric acid and sodium nitrate solution is presented. The starting material ...
Polyaniline stabilization of magnetic particles and immobilization of alpha-amylase
(Savez hemijskih inženjera, Beograd, 2018)
Magnetic particles (MAG), obtained by standard procedure of coprecipitation of Fe2+ and Fe3+ in an excess of ammonia, and polyaniline modified magnetic particles MAG-PANI were used as carriers for immobilization of a-amylase ...
Microfiltration with periodic gas backwashing as an alternative technique for increasing permeate flux
(Savez hemijskih inženjera, Beograd, 2018)
In this paper, the influence of operating parameters (transmembrane pressure, temperature, the flow rate of retentate) on the cross - flow microfiltration of synthetic fruit juice and periodic backwashing with air was ...
Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures
(Savez hemijskih inženjera, Beograd, 2017)
The present study estimated the cracking phenomenon in as-plasma-sprayed hydroxylapatite coatings (HACs) after they were being subjected to the severe cutting conditions in the direction perpendicular to the coating/substrate ...
Analysis of the treatment of plastic from electrical and electronic waste in the republic of Serbia and the testing of the recycling potential of non-metallic fractions of printed circuit boards
(Savez hemijskih inženjera, Beograd, 2017)
This paper presents the analysis of the quantity of plastic and waste printed circuit boards obtained after the mechanical treatment of electrical and electronic waste (E-waste) in the Republic of Serbia, as well as the ...