Претраживање
Приказ резултата 1-10 од 16
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
Finite element analysis of fracture resistance parameters for stationary semi-elliptical surface cracks in high strength steel / Analiza parametara otpornosti na lom metodom konačnih elemenata, kod stacionarnih polueliptičnih prslina u čeliku povišene čvrstoće
(Society for Structural Integrity and Life, Institute for Material Testing, 2015)
This study deals with numerical simulations based on elastic-plastic finite element method for nonlinear stress analyses on pre-cracked tensile specimens with high strength properties. The influence of crack geometry on ...
Application of exergy analysis in recycling streams / Primena eksergijske analize u reciklažnim tokovima
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
Materials for recycling always contain a certain degree of contamination. The presence of impurities i.e. contamination in the recycling streams causes a change in the composition of the original materials to recycle. As ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...
Micromechanical crack analysis of glass-epoxy laminated composites subjected to tension load / Mikromehanička analiza loma laminatnog staklo-epoksi kompozitnog materijala ispitivanog na zatezanje
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The main objective of this study is to determine tensile properties of the glass-epoxy polymer composite material. The material is glass fiber 280 g/m², 'twill woven' with 100 cm width, type - Interglas 92125, and epoxy ...
Immobilization of peroxidase from fresh horseradish extract for anthraquinone dye decolorization / Imobilizacija peroksidaze iz svežeg ekstrakta rena i primena u dekolorizaciji antrahinonskih boja
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
Synthetic dyes are used in all sectors of industry and represent a serious ecological problem. By the presence, anthraquinone dyes are right after the azo dyes. Unlike azo, anthraquinone dyes are considerably harder to ...
Indentation behaviour of 'soft film on hard substrate' composite system type / Ponašanje kompozitnih sistema tipa 'mek film na tvrdom supstratu' na testu utiskivanja
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This investigation has been carried out in order to analyse and compare the hardness response of different composite systems of the same type, named 'soft film on hard substrate' composite system. Composite systems of mono- ...
Synthesis of high-performance alkyd anticorrosion coatings based on waste poly(ethylene terephthalate) / Sinteza visokoefikasnih alkidnih antikorozionih premaza na bazi poli(etilen tereftalata)
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
Synthesis of high-performance anticorrosive coatings obtained from alkyd resins (ARs) based on waste poly(ethylene terephthalate) (PET) glycolyzates is presented. PET glycolyzates, synthesized by catalytic depolymerization ...
Investigation of copper(i) sulphide leaching in oxidative hydrochloric acid solution
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Present work is focused on the copper (I) sulphide leaching with sodium chloride in hydrochloric acid solution and with introduction of gaseous oxygen. Chemical reactions of leaching and their thermodynamic probabilities ...