Pretraživanje
Prikaz rezultata 1-10 od 13
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART I: Effect of Synthesis Parameters on Chemical Composition, Microstructure and Morphology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
Kinetic and operational electrolysis parameters determine the polarization characteristics, electrodeposition current efficiency, morphology, chemical composition and microstructure of nickel/iron/tungsten alloy deposits. ...
Effect of Electrodeposition Current Density on the Microstructure and Magnetic Properties of Nickel-cobalt-molybdenum Alloy Powders
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Nanostructured nickel-cobalt-molybdenum alloy powders were electrodeposited from an ammonium sulfate bath. The powders mostly consist of an amorphous phase and a very small amount of nanocrystals with an mean size of less ...
Investigation of Possibility for Stabilization and Valorization of Electric Arc Furnace Dust and Glass From Electronic Waste
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
This paper presents investigation of possibility for electric arc furnace dust (EAFD) and electronic waste (e-waste) valorization trough stabilization process, in order to achieve concurrent management of these two serious ...
An Experimental Study of Mechanical Properties and Heat Transfer of Acrylic Composites with Structural and Surface Modified Al2O3 Particles
(International Institute for the Science of Sintering (IISS), 2020)
Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat ...
Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles – Principal Component Analysis
(International Institute for the Science of Sintering, 2018)
This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 ...
Impact of Alumina Particles on the Morphology and Mechanics of Hybrid Wood Plastic Composite Materials
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2019)
Hybrid composite panels of Wood-Plastic Composites (WPC) consisting of wood and poly (methyl methacrylate) (PMMA) were reinforced with alumina particles and made by "hot pressing" method. Alumina-based particles were made ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART II: Effect of Microstructure on Hardness, Electrical and Magnetic Properties
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
Nanostructured nickel-iron-tungsten alloys were produced by electrodeposition from an ammoniacal citrate bath. The tungsten content of the alloy ranged from 0.8 wt.% to 11 wt.%, and the crystal grain size of the FCC phase ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Processing of gelatine coated composite scaffolds based on magnesium and strontium doped hydroxyapatite and yttria-stabilized zirconium oxide
(International Institute for the Science of Sintering, 2023)
Limited bone bank capacity and risk of infection are some of the main drawbacks of autologous and allogenic grafts, giving rise to synthetic materials for bone tissue implants. The aim of this study was to process and ...