Претраживање
Приказ резултата 31-40 од 62
Basalt-Polyester Hybrid Composite Materials for Demanding Wear Applications
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2020)
Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer ...
Thermal, Ceramic and Technological Properties of Clays used in Production of Roofing Tiles – Principal Component Analysis
(International Institute for the Science of Sintering, 2018)
This research describes a study of 11 selected samples of brick clays applied in roofing tile production, by using simultaneous thermal analysis. Additionally, the laboratory-sized samples were prepared and fired (850-950 ...
Prospect of Polysaccharide-Based Materials as Advanced Food Packaging
(MDPI, Basel, 2020)
The use of polysaccharide-based materials presents an eco-friendly technological solution, by reducing dependence on fossil resources while reducing a product's carbon footprint, when compared to conventional plastic ...
The advantages of using activated flux-cored wire compared to solid wire in the mag welding process from the aspect of metallurgical characteristics
(Croatian Metallurgical Soc, Zagreb, 2014)
This paper analyzes, from the metallurgical aspect, the quality of the new flux-cored wire intended for the MAG welding process in function of changes in shielding gas composition and changes in welding parameters. The ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
Use of chènevotte, a valuable co-product of industrial hemp fiber, as adsorbent for pollutant removal. Part i: Chemical, microscopic, spectroscopic and thermogravimetric characterization of raw and modified samples
(MDPI AG, 2021)
FINEAU (2021–2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose ...
Heat generation during plunge stage in friction stir welding
(Vinca Institute of Nuclear Sciences, 2013)
This paper deals with the heat generation in the Al alloy Al2024-T3 plate under different rotating speeds and plunge speeds during the plunge stage of friction stir welding. A 3-D finite element model is developed in the ...
Assessing the Bioactivity of Gentamicin-Preloaded Hydroxyapatite/Chitosan Composite Coating on Titanium Substrate
(Amer Chemical Soc, Washington, 2020)
The electrophoretic deposition process (EPD) was utilized to produce bioactive hydroxyapatite/chitosan (HAP/CS) and hydroxyapatite/chitosan/gentamicin (HAP/CS/Gent) coatings on titanium. The bioactivity of newly synthesized ...
Novel β-galactosidase nanobiocatalyst systems for application in the synthesis of bioactive galactosides
(Royal Society of Chemistry, 2016)
In this study, unmodified, amino modified and cyanuric chloride functionalized amino modified nonporous fumed nano-silica particles (FNS, AFNS and CCAFNS, respectively) were used for the development of efficient nanobiocatalysts ...
Influence of friction stir welding parameters on properties of 2024 t3 aluminium alloy joints
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2014)
The aim of this work is to analyse the process of friction stir welding (FSW) of 3 mm thick aluminium plates made of high strength aluminium alloy - 2024 T3, as well as to assess the mechanical properties of the produced ...