Претраживање
Приказ резултата 1-10 од 22
The tribological performance of hardfaced/thermal sprayed coatings for increasing the wear resistance of ventilation mill working parts
(Univerzitet u Kragujevcu - Fakultet inženjerskih nauka, Kragujevac, 2015)
During the coal pulverizing, the working parts of the ventilation mill are being worn by the sand particles. For this reason, the working parts are usually protected with materials resistant to wear (hardfaced/thermal ...
Influence of picosecond laser pulses on the microstructure of austenitic materials
(Springer, New York, 2011)
We investigate samples of austenitic materials - stainless steel and iron-based superalloy - which are widely used at high temperatures and pressures. The samples were exposed to Nd(3+):YAG laser pulses with a wavelength ...
Examination of the adhesion of polymer composite films based on Bis-GMA/TEGDMA on different metal substrates / Ispitivanje adhezije polimernih kompozitnih filmova na bazi Bis-GMA/TEGDMA na različitim metalnim podlogama
(Savez inženjera i tehničara Srbije, Beograd, 2018)
The subject of this study is the quantitative adhesion of a UV-curing composite film based on Bis-GMA (Bisphenol A glycidylmethacrylate) / TEGDMA (triethylene glycol dimethacrylate) as a matrix and particles doped with ...
Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties
(University of Novi Sad, Faculty of Technology, 2018)
Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were ...
Nimonic 263 microstructure and surface characterization after laser shock peening
(Croatian Metallurgical Soc, Zagreb, 2015)
The Laser Shock Peening (LSP) is applied to the surface of Nimonic 263 alloy. The changes in microstructure and surface topography are observed and analyzed by Scanning Electron Microscopy (SEM), profilometer and microhardness ...
Examination of mechanical properties of acrilyc composite materials with different AL2O3 reinforcement by brazil test / Ispitivanje mehaničkih svojstava akrilatnih kompozitnih materijala sa različitim AL2O3 ojačanjima brazilskim testom
(Savez inženjera i tehničara Srbije, Beograd, 2019)
Composite materials based on UV-curing acrylates and various alumina-based reinforcements represent material that is suitable for the use in dentistry, but also in other areas. Composites were made using four different ...
Picosecond laser shock peening of base Nimonic 263 material and laser welded Nimonic 263 alloy / Mehanička obrada pikosekundnim laserom osnovnog materijala i zavarenih spojeva legure Nimonik 263
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2015)
Laser welding is a welding process with a high energy density and numerous advantages over conventional welding methods (narrow heat affected zone, lower heat input, less distortion, and the like.) Mechanical treatment ...
Characterisation of biomedical titanium layers deposited by a vacuum plasma spray process
(Materiali in Tehnologije, 2021)
In this paper we will describe the process of the deposition of thick layers of VPS-Ti coating, which is used as a bonding layer for the upper porous Ti coatings on implant substrates. In order to deposit the powder, we ...
The advantages of using activated flux-cored wire compared to solid wire in the mag welding process from the aspect of metallurgical characteristics
(Croatian Metallurgical Soc, Zagreb, 2014)
This paper analyzes, from the metallurgical aspect, the quality of the new flux-cored wire intended for the MAG welding process in function of changes in shielding gas composition and changes in welding parameters. The ...
Development of Coated Electrodes with Solid Wire and Flux-Cored Alloyed Wire for Microalloyed Steel Welding
(MDPI, Basel, 2020)
In this paper, we will present our investigation of the quality of J55 microalloyed steel welds that were formed by a basic flux-cored wire electrodes that were of appropriate quality and alloyed with Ni and Mo. Based on ...