Претраживање
Приказ резултата 21-30 од 99
Biodegradable Cellulose/Polycaprolactone/Keratin/Calcium Carbonate Mulch Films Prepared in Imidazolium-Based Ionic Liquid
(MDPI, 2023)
Ionic liquid 1-butyl-3-methylimidazolium chloride [BMIM][Cl] was used to prepare cellulose (CELL), cellulose/polycaprolactone (CELL/PCL), cellulose/polycaprolactone/keratin (CELL/PCL/KER), and cellulose/polycaprolactone/ ...
The Design of a System for the Induction Hardening of Steels Using Simulation Parameters
(MDPI, 2023)
This paper presents the development of a piece of induction hardening equipment based on the foundations of the design, starting from zero. It was intended for steels in general, and was tested on unalloyed low- and ...
CELLULOSE-BASED WASTE STRUCTURE AND CHEMICAL COMPOSITION IMPACT ON THE ADSORPTION OF PHARMACEUTICALS / UTICAJ STRUKTURE I HEMIJSKOG SASTAVA CELULOZNOG OTPADA NA ADSORPCIJU FARMACEUTIKA
(Savez inženjera i tehničara tekstilaca Srbije, 2023)
In an attempt to reuse fibrous textile waste, and at the same time to reduce its quantity, waste hemp and
flax fibers, and cotton yarn were used as cheap and sustainable adsorbents for the removal of pharmaceuticals
from ...
Hydrothermally synthesized CeO2/ZnO nanocomposite photocatalysts for the enhanced degradation of Reactive Orange 16 dye
(Elsevier Ltd., 2023)
In this work, in order to improve the photocatalytic efficiency of ZnO, the optimal CeO2 content in ZnO powders was determined by varying the quantity of CeO2 from 0 to 10 mol%. The structural, microstructural, optical, ...
Plasma Treatment as a Sustainable Method for Enhancing the Wettability of Jute Fabrics
(MDPI, 2023)
In this paper, raw jute fabric was subjected to atmospheric pressure dielectric barrier discharge (at 150 or 300 Hz) to enhance its wettability, i.e., capillarity and wetting time. Attenuated Total Reflectance-Fourier ...
Magneto-Mechanical and Thermal Properties of Nd-Fe-B-Epoxy-Bonded Composite Materials
(MDPI, 2023)
Polymer-bonded magnets are a class of composite material that combines the magnetic properties of metal particles and the molding possibility of a polymeric matrix. This class of materials has shown huge potential for ...
Dispersive liquid–liquid microextraction and Monte Carlo simulation of margin of safety for octocrylene, EHMC, 2ES, and homosalate in sunscreens
(John Wiley and Sons Ltd., 2023)
Dispersive liquid–liquid microextraction (DLLME) using a floating organic drop has been optimized and used for the sample preparation of four commonly used ultraviolet filter (UVF) substances in sunscreens. Plackett–Burman ...
INTEGRITY AND RISK ASSESSMENT OF RECONSTRUCTED STEAM LINE / PROCENA INTEGRITETA I RIZIKA REKONSTRUISANOG PAROVODA
(Society for Structural Integrity and Life (DIVK), 2023)
The integrity assessment of high pressure steam pipeline
primarily requires stress state determination, including not
only effects of working pressure and temperature, but also
all acting loads. Toward this aim, the ...
WASTE MATERIALS AS ADSORBENTS FOR HEAVY METALS REMOVAL FROM WATER: COMPARATIVE ANALYSIS OF MODIFICATION TECHNIQUES
(SAVEZ INŽENJERA I TEHNIČARA TEKSTILACA SRBIJE, 2023)
This study aims to investigate the effect of alkalization and chemical coupling methods on the surface
and adsorption properties of waste cotton and cotton/polyester yarns. The simple and cheap alkali treatment was
performed ...
Assessment of the burden of disease due to PM2.5 air pollution for the Belgrade district
(VINČA Institute of Nuclear Sciences, 2023)
The health effects attributed to exposure to ambient PM2.5 concentrations
above 10 μg/m3
by using the AirQ+ modeling software were assessed. The
hourly concentrations of PM2.5 were collected from 13 air pollution
monitoring ...