Претраживање
Приказ резултата 131-140 од 155
Analysis of the tool plunge in friction stir welding comparison of aluminum alloys 2024 t3 and 2024 t351
(Univerzitet u Beogradu - Institut za nuklearne nauke Vinča, Beograd, 2016)
Temperature, plastic strain and heat generation during the plunge stage of the friction stir welding of high-strength aluminum alloys 2024 T3 and 2024 T351 are considered in this work. The plunging of the tool into the ...
Mechanical properties of composites based on unsaturated polyester resins obtained by chemical recycling of poly(ethylene terephthalate) / Mehanička svojstva kompozita na bazi nezasićenih poliestarskih smola dobijenih hemijskom reciklažom poli(etilen-tereftalata)
(Association of Chemical Engineers of Serbia, 2013)
Composites based on unsaturated polyester (UPe) resins and fumed silica AEROSIL® RY 50, NY 50, RX 50 and NAX 50, as well as graphite, TiO2 or organically modified clay CLOISITE 30B were prepared in order to investigate the ...
Analysis of mechanical and structural properties of micro alloyed steel welded joints depending on quality of cored wire
(University of Osijek, Tech Fac, Slavonski Brod, 2013)
The aim of this study was to master new quality cored wires made of steel strips and the cores filled with metal powders and low molecular hydrophobic compounds. For experimental research, the specimens were made of micro ...
Waste reduction algorithm used as the case study of simulated bitumen production process
(Association of the Chemical Engineers of Serbia, 2011)
Algoritam za redukciju otpada (eng. waste reduction algorithm – WAR) jeste metodologija
koja se može koristiti za procenu potencijalnog uticaja tehnoloških procesa na životnu
sredinu. Analizom pojedinačnih stupnjeva ...
The influence of powder feed rate on mechanical properties of atmospheric plasma spray (APS) Al-12Si coating
(Walter de Gruyter Gmbh, Berlin, 2019)
In this paper, structural and mechanical properties of APS - atmospheric plasma spray coating Al-12Si are presented. The aim of the research was the optimisation of the flow of powder to produce layers with optimal mechanical ...
A coupled thermo-mechanical model of friction stir welding
(Vinca Institute of Nuclear Sciences, 2012)
A coupled thermo-mechanical model was developed to study the temperature fields, the plunge force and the plastic deformations of Al alloy 2024-T351 under different rotating speed: 350, 400, and 450 rpm, during the friction ...
Friction-stir welding of high-strength aluminium alloys and a numerical simulation of the plunge stage
(Institute of Metals and Technology, 2012)
This paper defines a set of welding parameters for the Friction-Stir Welding (FSW) of two forged panels of the alloy EN AW 7049A in a T652 temper and discusses the plunge stage of FSW using numerical modeling. This ...
Electrophoretically deposited hydroxyapatite-based composite coatings loaded with silver and gentamicin as antibacterial agents
(Srpsko hemijsko društvo, Beograd, 2019)
Increasing need for improved, compatible bone tissue implants led to the intensive research of novel biomaterials, especially hydroxyapatite (HAP)-based composite materials on titanium and titanium alloy surfaces. Owing ...
Salt template zirconia reinforcing particles as possible reinforcement for PMMA matrix composite
(Sage Publications Ltd, London, 2019)
To obtain flakes like zirconia particles at relatively low temperature, the synthesis method for producing zirconia particles on the surface of salt particles that serve as a template is examined. The produced particles ...
The impact of puffball autolysis on selected chemical and biological properties: puffball extracts as potential ingredients of skin-care products
(Srpsko biološko društvo, Beograd, i dr., 2019)
Puffballs are fungi that produce globose fruiting bodies that undergo autolysis, transforming their insides into a spore bearing, powdery mass. Mature fruiting bodies are traditionally used to treat open skin wounds. In ...