Претраживање
Приказ резултата 1-10 од 736
Using the numerical simulations and comparative diagnostic methods to optimize the product
(The Bulletin of the National R&D Institute for Welding and Material Testing - ISIM Timişoara, Romania, 2012)
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Optimizing the content of nickel in flux-cored wire intended for welding micro-alloyed steels / Optimizacija sadržaja nikla u punjenoj žici namenjenoj za zavarivanje mikrolegiranih čelika
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2014)
This paper presents the results related to organizing production of flux-cored wire alloyed with Ni and Mo according to standard AWS A5.29 intended for the MAG welding process. On the experimental line for steel strip ...
Comparative analysis of functionality of spray dried whey protein hydrolysates obtained by enzymatic and microbial hydrolysis
(Savez hemijskih inženjera, Beograd, 2018)
The aim of this study was to examine the bioactive potential of hydrolysate powders produced by enzymatic and microbial hydrolysis of whey proteins followed by spray drying, in order to reveal which one of these processes ...
Immobilization of dextransucrase on functionalized TiO2 supports
(Elsevier Science Bv, Amsterdam, 2018)
The TiO2 based hybrid supports with different functional groups (amino, glutaraldehyde or epoxy) were prepared and their influence on immobilization of dextransucrase (DS) was studied. Novel synthetic route for surface ...
Farmaceutski preparati i opojne droge kao kontaminirajuće supstance površinskih i otpadnih voda / PHARMACEUTICAL PREPARATIONS AND ILLICIT DRUGS AS CONTAMINATING SUBSTANCES OF SURFACE AND WASTEWATER
(Zastita Materijala, 2018)
Prisustvo farmaceutskih preparata i opojnih droga u otpadnim, površinskim i podzemnim vodama
predstavlja ozbiljan problem po zdravlje ljudi. Razlog za to je činjenica da ova jedinjenja poseduju
biološku aktivnost, lako ...
Mechanical properties and microstructure of molybdenum coating layers deposited vacuum plasma spray process / Mehanička svojstva i mikrostruktura slojeva prevlake molibdena deponovane vakuum plazma sprej procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2019)
Molybdenum coatings due to their excellent wear resistant properties and sliding characteristics under dry friction conditions are often used in applications to resist friction and dry sliding. Since molybdenum metal is ...
Advantage of use of activated flux-cored wire instead of solid wire with the mag welding process from the mechanical properties aspect
(Croatian Metallurgical Soc, Zagreb, 2013)
The objective of this paper is the analysis and evaluation of the quality of the new flux-cored wire designed for the MAG welding process that was developed and produced using special laboratory equipment. Experimental ...
Influence of Chitosan Coating on Mechanical Stability of Biopolymer Carriers with Probiotic Starter Culture in Fermented Whey Beverages
(Hindawi Ltd, London, 2015)
The aim of this study was to improve the mechanical stability of biopolymer carriers and cell viability with addition of chitosan coating during fermentation process and product storage. Dairy starter culture (1% (w/v)) ...
Impact of carrier material on fermentative activity of encapsulated yoghurt culture in whey based substrate
(Savez hemijskih inženjera, Beograd, 2017)
The main objectives of this paper were to study the influence of the carrier material used for encapsulation and of bead size to fermentative activity and viability of the dairy starter culture Lactoferm ABY 6. Encapsulation ...