Претраживање
Приказ резултата 1-10 од 21
New functional polymers obtained by amination of PVC
(Proceedings of the fourth Yugoslav Materials Research Society Conference (YUCOMAT IV), 2002)
A new procedure for introduction of aromatic diamines into polymer, in particular into poly(vinyl chloride) (PVC) molecule, was developed. Produced materials have attractive properties such as combination of good film-forming, ...
Semi-interpenetrating networks based on POLY(N-isopropyl acrilamide) and POLY(N-vinylpyrrolidone) / Semi-interpenetrirajuće polimerne mreže na bazi POLI(N-izopropilakrilamida) i POLI(N-vinilpirolidona)
(Association of Chemical Engineers of Serbia, 2007)
Three series of semi-interpenetrating polymer networks based on cross-linked poly(N-isopropylacrylamide), PNIPA, and 1, 2 and 3 wt% of linear poly(N-vinylpyrrolidone), PVP, were synthesized in order to improve the mechanical ...
Investigation of thermodynamic properties and phase equilibria in Ag-In-Sn system / Ispitivanje termodinamičkih veličina i faznih ravnoteža u sistemu Ag-In-Sn
(Savez inženjera i tehničara Srbije, Beograd, 2006)
Lead - free soldering became very popular in the whole world, because of high ecological demands in industry. Most of alternative alloys have high content of tin, and some of them are already used in electronic industry. ...
Re-refining of waste mineral insulating oil by extraction with N-methyl-2-pyrrolidone
(Elsevier Science Bv, Amsterdam, 2006)
Extraction with N-methyl-2-pyrrolidone (NMP) via the three-stage mixer-settler operation was studied as possible process for re-refining of waste mineral insulating oil. The following extraction process parameters were ...
A new technological solution for the manufacture of a borer for iron notch opening at the blast furnace plant / Primena aluminotermijskog postupka izrade i zavarivanja vrha burgija koje se koriste za otvoranje visoke peći tokom ispusta gvožđa
(Institut za istrazivanja i projektovanja u privredi, 2004)
A new technology for the manufacture of a borer by alumino-thermal method, system design for performing alumino-thermal reaction, as well as required quality of termite steel, is disclosed in this paper. In addition to ...
Possibilities of recycling of magnesium and magnesium alloys
(Savez inženjera metalurgije Srbije, Beograd, 2004)
In this paper are presented results of experimental investigation of processing of non oil-contaminated metal scrap based on magnesium and its alloys. These are the firs investigations of magnesium scrap recycling in Serbia ...
Preliminary studies on controlled release of acetylsalycilic acid from membrane module
(Association of Chemical Engineers of Serbia, 2004)
Selective removal of heavy metals from metal-bearing wastewater in a cascade line reactor
(Ecomed Publishers, Landsberg, 2007)
Goal, Scope and Background. This paper is a part of the research work on 'Integrated treatment of industrial wastes towards prevention of regional water resources contamination INTREAT' the project. It addresses the ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
The effect of the presence of alcohol in the dispersing phase of oxide sols on the properties of RuO2-TiO2/Ti anodes obtained by the sol-gel procedure / Uticaj prisustva alkohola u disperznoj sredini oksidnih solova ha osobine RuO2-TiO2/Ti anoda dobijenih sol-gel postupkom
(Serbian Chemical Society, Belgrade, 2000)
The effect of the addition of ethanol and 2-propanol to the dispersing phase of TiO2 and RuO2 sols mixture on the morphology and, consequently, on the electrochemical properties of the sol-gel obtained activated titanium ...