Претраживање
Приказ резултата 1-10 од 166
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...
Nanostructured intrinsically conducting polymers formed by electrochemical synthesis / Nanostruktuirani elektroprovodni polimeri dobijeni elektrohemijskom sintezom
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Due to unique properties of intrinsically conducting polymers (ICP) such as: electrical conductivity, reversible electrochemistry, optical activity, biocompatibility, environmental and corrosion stability, they still ...
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
Chemical durability of sintered glass-composite prepared from glass cullet and waste foundry sand
(Metallurgical & Materials Engineering, 2021)
In this study, the glass-composite was prepared using glass cullet and waste foundry sand as raw materials. The powder technology route was employed. The mixtures containing 10-50 wt% of the sand were sintered at T = 750 ...
Effect of heating rate on precipitation of peak-aged Al-Li (8091) alloy: A quantitative approach
(Savez inženjera metalurgije Srbije, Beograd, 2010)
Samples of Al-Li (8091) alloy were solution treated at 540ºC for 30 min, water-quenched and continuously heated in oil at 0.05 and 0.1ºC/min rates, from room temperature to 190ºC when the peak hardness was achieved. Having ...
Innovative and generic pharmaceuticals industry and drugs market / Inovativna i generička farmaceutska industrija i tržište lekova
(Economics institute, Belgrade, 2010)
The pharmaceutical industry consists of two sectors: the innovative sector and generic sector. The innovative pharmaceutical industry is totally dependent on patents and these companies are focused on protecting against ...
Influence of Cr, Mn and Mo on structure and properties of V microalloyed medium carbon forging steels
(Savez inženjera metalurgije Srbije, Beograd, 2010)
The influence of Cr, Mo and Mn on microstructure and mechanical properties of V-microalloyed medium-carbon steels has been studied by means of metallography and mechanical testing. Cr, Mn and Mo addition promotes the ...
Influence of the synthesis procedures on pt catalyst activity for ethanol electrooxidation reaction / Uticaj postupka sinteze na aktivnost platinskih katalizatora za reakciju elektrooksidacije etanola
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Carbon supported platinum catalysts for ethanol electrooxidation were synthesized by modified polyol synthesis method, assisted by microwave or reflux heating. Synthesized catalysts were characterized by XRD, STM and TGA ...