Pretraživanje
Prikaz rezultata 31-40 od 146
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Comparative analysis of the chemical composition and antimicrobal activities of some of Lamiaceae family species and eucaliptus (Eucaliptus globules M) / Komparativna analiza hemijskog sastava i antimikrobne aktivnosti nekih etarskih ulja familije Lamiaceae i etarskog ulja eukaliptusa (Eucaliptus globules M)
(Faculty of Technology, Novi Sad, 2014)
The aim of this study was to evaluate and compare the antimicrobial activity of four essential oils that belong to Lamiaceae family (sage, oregano, thyme) and eucalyptus oil. Gas chromatography coupled with mass spectrometry ...
Time: Temperature superposition principle: Application of WLF equation in polymer analysis and composites / Princip superponiranja vremena i temperature - primena WLF jednačine za ispitivanje polimera i kompozita
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Polymers are the most studied viscoelastic material. The shorter times (high frequencies) corresponding to lower temperatures and long times (low frequencies) to high temperatures. This represents the quantitatively applied ...
Influence of acidic solutions on the strain distribution in glasspolyester composite pipes subjected to internal pressure / Uticaj rastvora kiselina na raspodelu deformacija kod staklo-poliestar kompozitnih cevi istaloženih dejstvu unutrašnjeg pritiska
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
The basic subject of this paper was the determination of the strain distribution in glass-polyester composite pipes subjected to internal pressure. Firstly, the test was performed on virgin pipe segments (without the ...
Magnetic behaviour of hybrid magnetic composite materials / Magnetno ponašanje hibridnih magnetnih kompozitnih materijala
(Inženjersko društvo za koroziju, Beograd, 2014)
Polymer bonded magnets are contemporary materials with a very large range of applications. The objective of this study is to assess how different content of Nd-Fe-B and/or barium ferrite particles affect on magnetic and ...
Basic principles and applications of photoelectrochemical reactions / Osnovni principi i primena fotoelektrohemijskih reakcija
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
The paper discusses the basic principles of photoelectrochemistry and photo electrochemical reactions. Considered the application photoelectrochemicl cells in the conversion of the sun iradiation energy into electricity. ...
The effect of cooling rate of slag from primary copper production in the valorization of copper in the flotation process
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Technological procedure of slow cooling slag from primary copper production is applied in the purpose of copper recovery in the level of 98.5% to blister. This technological procedure is divided into two phases, first slow ...
Alkyd nanocomposite coatings based on waste pet glicolyzates and modified silica nanoparticles / Alkid nanokompozitni premazi bazirani na otpadnim pet glikolizatima modifikovani nanočesticama silike
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Synthesis of high-performance alkyd resins (ARs) based on waste poly(ethylene terephthalate) (PET) glycolyzates is presented. PET glycolyzates were synthesized by catalytic depolymerization with trimethylolpropane (TMP) ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...