Search
Now showing items 1-10 of 178
Impact of roughness of Zn-Mn coatings on corrosive stability / Uticaj hrapavosti Zn-Mn prevlaka na korozionu postojanost
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
This paper involves electrochemical deposition of Zn-Mn coatings from four solutions. We measured their roughness and corrosion stability. We used cathodes made of steel of unknown composition that were licensed under the ...
Chemical durability of sintered glass-composite prepared from glass cullet and waste foundry sand
(Metallurgical & Materials Engineering, 2021)
In this study, the glass-composite was prepared using glass cullet and waste foundry sand as raw materials. The powder technology route was employed. The mixtures containing 10-50 wt% of the sand were sintered at T = 750 ...
Influence of Cu and Mn content on the properties of Al-Mg4.5-(Mn,Cu) type alloy sheets
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Influence of Cu and Mn content on the grain structure, precipitation effects and mechanical properties of two Al-Mg4.5-(Mn,Cu) type sheets was considered. It was found that a variety of grain size can be obtained in alloy ...
Hydrometallurgical process for extraction of metals from electronic waste, part II: Development of the processes for the recovery of copper from printed circuit boards (PCB)
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Rapid technological development induces increase of generation of used electric and electronic equipment waste, causing a serious threat to the environment. Waste printed circuit boards (WPCBs), as the main component of ...
Hydrometallurgical process for extraction of metals from electronic waste, Part I: Material characterization and process option selection
(Savez inženjera metalurgije Srbije, Beograd, 2009)
Used electronic equipment became one of the fastest growing waste streams in the world. In the past two decades recycling of printed circuit boards (PCBs) has been based on pyrometallurgy, highly polluting recycling ...
Quality assurance of storage tanks after in-service crack repairs / Osiguranje kvaliteta rezervoara u eksploataciji posle popravke prslina
(Society for Structural Integrity and Life, Institute for Material Testing, 2013)
According to the Pressure Equipment Directive (PED 97/23/EC) a new produced storage tank can be accepted on the market only if the required quality is proved. In this way the structural integrity might be at the requested ...
The analysis of the tribological properties of multiple strengthened nanocomposite of the Cu-Al2o3 system
(Savez inženjera metalurgije Srbije, Beograd, 2011)
This paper presents the results of examined tribological properties of the multiple strengthened nanocomposite Cu-Al2O3 system. Cu-Al2O3 composite powder was obtained by combination of the thermo-chemical procedure and ...
Modern steels: Transformation induced plasticity / Savremeni čelici - transformacijom izazvana plastičnost
(DUZS - Društvo za unapređivanje zavarivanja u Srbiji, Beograd, 2011)
TRIP čelici danas zauzimaju značajno mesto u komercijaloj upotrebi u vozilima i konstrukcijama kod kojih je jedan od glavnih zahteva redukcija sopstvene težine. Optimalna kombinacija udela stabilisanog austenita i stepen ...
Vrednovanje intelektualne svojine
(Economics institute, Belgrade, 2011)
Intellectual Property Rights (IPRs) and Intangible Assets (IAs) can be highly valuable playing a key role in many fields of business, touching nearly all aspects of a company: products development, human capital, marketing ...
Structural properties of Co, Ni and Mo powders obtained by electrochemical deposition
(Savez inženjera metalurgije Srbije, Beograd, 2011)
Magnetic thin films based on iron group elements (Fe, Co, Ni) are currently used in computer's hard disk drives and in MEMS, whereas electrodeposition is a suitable method to obtain these materials. The powders of metals ...