Претраживање
Приказ резултата 1-10 од 30
Chemical durability of sintered glass-composite prepared from glass cullet and waste foundry sand
(Metallurgical & Materials Engineering, 2021)
In this study, the glass-composite was prepared using glass cullet and waste foundry sand as raw materials. The powder technology route was employed. The mixtures containing 10-50 wt% of the sand were sintered at T = 750 ...
Solvent extraction and entrainment problem
(Association of Metallurgical Engineers of Serbia, 2020)
Applications of solvent extraction operations and processes play one of the most important roles in Hydrometallurgy. Therefore, in this brief review, some general concepts for selected representative applications are ...
Effect of process parameters on the phase transformation kinetics in copper-based alloys and composites
(Metallurgical & Materials Engineering, 2020)
Copper-based alloys and composites, owing to their convenient properties, are being considered essential materials in various industries. Since copper possesses an ability to develop high corrosion resistance, putting it ...
Application of raw volcanic rock found in etna valley as an adsorbent of chromates, arsenates and selenates
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This paper aims to determine the potential of volcanic rock found in Etna valley as an adsorbent of heavy metals in anionic form (chromates, arsenates, and selenates). Characterization of the volcanic rock was done with ...
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
Synthesis of nife2o4 nanofibers by joint sol-gel and electrospinning technique
(Savez inženjera metalurgije Srbije, Beograd, 2018)
In this study, electrospinning combined with sol-gel technique is applied in order to produce magnetic nickel ferrite (Ni-ferrite) nanofibers. The prepared Ni-ferrite gel was mixed with poly(vinylpyrrolidone) (PVP) solution ...
Defect formation during synthesis and welding of silver nanowires for solar cell applications
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Structural defects such as stacking faults and twins, observed in many face-centered cubic (FCC) structured metals and alloys with low stacking fault energies, in general, play an important role in microstructure evolution, ...
Investigation of copper(i) sulphide leaching in oxidative hydrochloric acid solution
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Present work is focused on the copper (I) sulphide leaching with sodium chloride in hydrochloric acid solution and with introduction of gaseous oxygen. Chemical reactions of leaching and their thermodynamic probabilities ...
Optimizing the thermal gradient and the pulling speed in a thermoplastic pultrusion process of pet/e glass fibers using finite element method
(Savez inženjera metalurgije Srbije, Beograd, 2018)
A thermoplastic pultrusion process was examined using commercial fiber roving of PET/E glass, to determine the optimum pulling speed and optimal zonal temperatures. Finite element analysis predicted heat transfer through ...