Pretraživanje
Prikaz rezultata 11-20 od 75
The crystal growth of NASICON phase from the lithium germanium phosphate glass
(International Institute for the Science of Sintering, 2023)
The crystal growth rate of LiGe2(PO4)3 phase from lithium germanium-phosphate glass was studied. The glass have been homogenized using the previously established temperature-time conditions, which make it possible to remove ...
Fast Oxide-Ion Conductors in Bi2O3-V2O5 System: Bi108-xVxO162+x(x=4-9) with 3 x 3 x 3 Superstructure
(Science of Sintering, 2021)
In this study, the possibility to stabilize O-2 ion conductors in Bi2O3-V2O5 system was investigated. Six pseudo-binary Bi2O3-V2O5 mixtures [3.50 lt x(V2O5) lt 8.50 mol%] were thermally treated at 1000 degrees C for 1 ...
Novel Magnetic Polymer/bentonite Composite: Characterization and Application for Re(VII) and W(VI) Adsorption
(Science of Sintering, 2021)
A novel magnetic polymer/bentonite composite was prepared by suspension copolymerization of glycidyl methacrylate and ethylene glycol dimethacrylate in the presence of magnetic bentonite (MB-PGME) and functionalized with ...
Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2017)
Mechanical shock of zircon based ceramic induced by cavitation erosion testing was investigated in this study. Several parameters were followed in order to determine level of material degradation during the cavitation ...
Investigation on the Adsorption of the Carbamate Pesticide Methomyl from Aqueous Solution using Modified Co-Beta Zeolite Particles
(International Institute for the Science of Sintering (IISS), 2023)
Adsorption of carbamate pesticide Methomyl by Co-Beta Zeolite particles prepared by wet ion-exchange method from aqueous solutions was studied. The effect of zeolite and pesticide concentrations, pH value, and sintering ...
Effects of plastic deformation on the properties of W-Ni-Fe heavy alloys
(International Institute for the Science of Sintering, Beograd, 2001)
The effects of reduction in area due to rotary forging on the structure, physical and mechanical properties of 92,5W-5Ni-2,5Fe heavy alloy rods have been presented in this paper. Sintered rods (20mm) were rotary forged ...
Influence of Raster Angle on Tensile Properties of FDM Additively Manufactured Plates made from Carbon Reinforced PET-G Material
(Belgrade : Association for ETRAN Society, 2023)
Tensile properties of thin plate specimens made from short carbon fiberreinforced PET-G material are experimentally evaluated for various raster angles(printing directions). In additive manufacturing (AM), raster angle is ...
The effect of Y2O3 addition on thermal shock behavior of magnesium aluminate spinel
(International Institute for the Science of Sintering, Beograd, 2009)
The effect of yttria additive on the thermal shock behavior of magnesium aluminate spinel has been investigated. As a starting material we used spinel (MgAl2O4) obtained by the modified glycine nitrate procedure (MGNP). ...
Magnetic properties of ND Rich Melt-Spun ND-FE-B alloy
(International Institute for the Science of Sintering, Beograd, 2005)
As a part of these experimental investigations of melt-spun Nd-Fe-B alloy with Nd rich content in relation to Nd2Fe14B prepared by rapid quenching process for optimally selected cooling rate and heat treatment, the influence ...
Influence of the damage level during quenching on thermal shock behavior of low cement castable
(International Institute for the Science of Sintering, Beograd, 2010)
In the recent decades, the use of unshaped monolithic refractories has been increasing greatly because of their significant advantages over other shaped refractory bricks of the same class. A low cement high alumina castable ...