Претраживање
Приказ резултата 1-10 од 168
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...
Preservation of vitamin C, lycopene and carbohydrate content in tomato dried in a tunnel type dryer / Očuvanje vitamina C, likopena i ugljenih hidrata u plodovima paradajza sušenim u tunelskom tipu sušara
(Institute for Food Technology, Novi Sad, 2017)
The aim of this study was to find an optimal way of tomato drying in a tunnel type dryer, in order to achieve the lowest possible losses in nutritive value of dried tomato products. Domestic variety of tomato (SP-109) was ...
Micromechanical crack analysis of glass-epoxy laminated composites subjected to tension load / Mikromehanička analiza loma laminatnog staklo-epoksi kompozitnog materijala ispitivanog na zatezanje
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The main objective of this study is to determine tensile properties of the glass-epoxy polymer composite material. The material is glass fiber 280 g/m², 'twill woven' with 100 cm width, type - Interglas 92125, and epoxy ...
The influence of light on corrosion of polyaniline coated mild steel / Uticaj osvetljenosti na koroziju mekog čelika sa prevlakom polianilina
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
The influence of light of the mild steel corrosion in 3% NaCl solution with polyaniline coating based on the possibilities that polyaniline can generate photoelectrons, even in the laboratory conditions has been investigated.
Synthesis of nife2o4 nanofibers by joint sol-gel and electrospinning technique
(Savez inženjera metalurgije Srbije, Beograd, 2018)
In this study, electrospinning combined with sol-gel technique is applied in order to produce magnetic nickel ferrite (Ni-ferrite) nanofibers. The prepared Ni-ferrite gel was mixed with poly(vinylpyrrolidone) (PVP) solution ...
Techno-economic analysis of unsaturated polyester production from waste PET / Tehno-ekonomska analiza proizvodnje nezasićenih poliestara iz otpadnog PET-a
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Unsaturated polyester resins (UPe) were synthesized from maleic anhydride and products of glycolysis, obtained by polyethylene terephthalate (PET) depolymerization with dipropylene glycol (DPG) in the presence of tetrabutyl ...
Leakage of an austenitic steel CO2 storage tank / Curenje posude za skladištenje CO2 od austenitnog čelika
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
After the occurrence of water droplets on the manhole outer wall of a storage tank for carbon dioxide, by detailed inspection, a net of cracks is detected in the manhole flange, close to the welded joint between the flange ...
Assessment of the behaviour of fatigue loaded HSLA steel welded joint by applying fracture mechanics parameters / Procena ponašanja zavarenog spoja HSLA čelika opterećenog na zamor primenom parametara mehanike loma
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
From a fracture mechanics point of view on welded joints, it is assumed that the welded joint is pre-cracked such as that the fatigue life of the pre-cracked structure is then determined by the period of crack growth under ...
Estimation of phosphorus distribution ratio at the end of blowing in bof
(Metallurgical & Materials Engineering, 2021)
In integrated steel plants, the removal of phosphorous normally takes place during the primary basic oxygen furnace (BOF) steelmaking process. Phosphorous is usually introduced to the integrated steelmaking process through ...
The effect of friction stirs welding speed on microstructure, mechanical properties and IGC of EN AW-5083 plates
(Advanced Technologies and Materials, 2019)
The aim of this work was to evaluate the influence of welding speed on microstructure, mechanical properties, as well as Intergranular corrosion (IGC) susceptibility of EN AW-5083 alloy welded using FSW. FSW was performed ...