Pretraživanje
Prikaz rezultata 1-10 od 19
TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
(ETRAN, 2022)
Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal ...
Mechanical Properties of Biomass-derived Silica Nanoparticles Reinforced PMMA Composite Material
(Science of Sintering, 2022)
Rice husk was used to produce silica particles, which were then used to reinforce the polymer matrix. The synthesized SiO2 particles were characterized using X-ray diffraction, Fourier transforms infrared spectroscopy ...
Comparison of Mechanical Behavior of SiC Sintered Specimen to Analysis of Surface Defects
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Silicon carbide is the material that in sintered form is suiTab. for protection from impact as part of the multilayered structure. Its role is to accumulate energy from the projectile, to plastically deform the projectile ...
Solid state synthesis of extra phase-pure Li4Ti5O12 spinel
(Belgrade : International Institute for the Science of Sintering, 2011)
Extra phase-pure Li4Ti5O12 spinel with particle sizes less than 500 nm was synthesized by solid state reaction of mechanochemicaly activated mixture of nano anatase and Li2CO3 for a very short annealing time, 4 h at 800°C. ...
Modeling of the Mechanical Behavior of Fiber-Reinforced Ceramic Composites Using Finite Element Method (FEM)
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC) is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary ...
Processing of gelatine coated composite scaffolds based on magnesium and strontium doped hydroxyapatite and yttria-stabilized zirconium oxide
(International Institute for the Science of Sintering, 2023)
Limited bone bank capacity and risk of infection are some of the main drawbacks of autologous and allogenic grafts, giving rise to synthetic materials for bone tissue implants. The aim of this study was to process and ...
Structural, Morphological and Electrical Properties of Alumina/YAG Composites as Solid Electrolyte for IT - SOFC
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
Alumina/YAG composites (AYX_t) with high relative density (99.2 %TD) were successfully obtained by mixing commercial alumina powder with different volume fractions of yttrium aluminium garnet (Y3Al5O12-YAG; 7, 14, 21 and ...
Investigation of Possibility for Stabilization and Valorization of Electric Arc Furnace Dust and Glass From Electronic Waste
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
This paper presents investigation of possibility for electric arc furnace dust (EAFD) and electronic waste (e-waste) valorization trough stabilization process, in order to achieve concurrent management of these two serious ...
Synthesis, Structure and Properties of Nickel-Iron-Tungsten Alloy Electrodeposits PART I: Effect of Synthesis Parameters on Chemical Composition, Microstructure and Morphology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
Kinetic and operational electrolysis parameters determine the polarization characteristics, electrodeposition current efficiency, morphology, chemical composition and microstructure of nickel/iron/tungsten alloy deposits. ...
Effect of milling and annealing on microstructural, electrical and magnetic properties of electrodeposited Ni-11.3 Fe-1.4w alloy
(International Institute for the Science of Sintering, Beograd, 2012)
A nanostructured Ni-11.3Fe-1.4W alloy deposit was obtained from an ammonium citrate bath at a current density of 600 mAcm-2. XRD analysis shows that the deposit contains an amorphous matrix having embedded nanocrystals of ...