Претраживање
Приказ резултата 1-10 од 14
Oxidation and erosion behaviour of SiC-HfC multilayered composite
(Univerzitet u Novom Sadu - Tehnološki fakultet, Novi Sad, 2014)
The fabrication of SiC-HfC ceramic composite via self-propagating high-temperature synthesis and simultaneous consolidation was investigated. Dense composite consisting of alternating layers of SiC and HfC was obtained by ...
Microstructural properties and cavitation behavior of hypereutectic Al-Si alloy obtained by rheocasting process / Mikrostrukturna svojstva i kavitaciono ponašanje nadeutektičke Al-Si legure dobijene reokasting postupkom
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The purpose of this study was to investigate possible application of AlSi alloy produced by rheocasting process in cavitation conditions. A rheocasting process was used to refine the as cast microstructure and improve the ...
Semi-empirical software for the aluminothermic and carbothermic reactions
(Association of Metallurgical Engineers of Serbia, 2014)
Understanding the reaction thermochemistry as well as formatting the empirical data about element distribution in gas-metal-slag phases is essential for creating a good model for aluminothermic and carbothermic reaction. ...
Micromechanical fracture analysis of laminated glass-epoxy composite material tested by bending / Mikromehanička analiza loma laminatnog staklo-epoksi kompozitnog materijala ispitivanog savijanjem
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The object and purpose of this work is the micromechanical analysis of failures caused by mechanical tests of laminate glass-epoxy composite material in bending. The structure of glass-epoxy composite material is a glass ...
Organoclay-polymer nanocomposites / Organoglina-polimerni nanokompoziti
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The properties of polymer nanocomposites exceed the properties of common composite materials due to the nanoscale size and morphology of the fillers used. Particulate fillersare commonly used in polymers forimproved ...
Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheets
(Association of Metallurgical Engineers of Serbia AMES, 2014)
In this study, fully annealed AA5083 type alloy sheets with 1 mm in thickness
were processed by accumulative roll bonding (ARB) at room temperature, up to 6 ARB
cycles. It was found that microstructure was refined and ...
Assessment of the integrity of welded pipes / Procena integriteta zavarenih cevi
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The subject of the paper is analysis of the integrity of welded pipes made of API J55 steel by high frequency contact welding (HF). Experimental research on the mechanical properties of the base material was conducted on ...
Modelling and optimization of surfactant sensor response characteristics for the use in surface water and wastewater analysis / Modelovanje i optimizovanje održivih karakteristika tenzidnog senzora za korišćenje pri analizi površinskih i otpadnih voda
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
The theoretical model of potentiometric titration curves of sodium dodecyl sulfate (anionic surfactant) was proposed and the response parameters of two surfactant sensors (commercial and self-made) were investigated. The ...
Treatment of waste sulfuric acid copper electrolyte / Tretman otpadnog sumporno-kiselog elektrolita bakra
(Institut za rudarstvo i metalurgiju, Bor, 2014)
The aim of this paper was to investigate the possibility of using the copper anodes with high nickel content for electrolytic treatment of waste sulfuric acid copper electrolyte. Nickel content in each anode was about 10 ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Engineering Society for Corrosion, Belgrade, Serbia, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...