Претраживање
Приказ резултата 91-100 од 178
Production of rubber plasticizers based on waste PET: Techno-economical aspect / Sinteza plastifikatora iz otpadnog PET-a za primenu u gumenim proizvodima - tehno-ekonomska analiza
(Engineering Society for Corrosion, Belgrade, Serbia, 2017)
Production of rubber plasticizers, based on waste poly(ethylene terephthalate) (PET), and economic effectiveness of developed technologies are presented and discussed. Waste PET glycolyzates, named diisononyl terephthalate(DINTP), ...
Tailoring the corrosion resistance of Zn-Mn coating by electrodeposition from deep eutectic solvents / Poboljšanje korozione postojanosti Zn-Mn prevlake, elektrohemijskim taloženjem iz dubokih eutektičkih smeša
(Engineering Society for Corrosion, Belgrade, Serbia, 2018)
Well adhered, homogenous coatings were obtained from deep eutectic solvents (DES) based on choline chloride and urea, at current densities up to 20 mA cm-2. The coatings' morphology was analyzed by atomic force microscopy, ...
Influence of the structural changes on cavitation resistance of Al18SiCuMg alloy produced by rheocasting process / Uticaj strukturnih promena na kavitacionu otpornost Al18SiCuMg legure proizvedene reokasting procesom
(Engineering Society for Corrosion, Belgrade, Serbia, 2015)
The influence of stirring speeds of 1000 and 1500 r/min on the microstructure of Al18SiCuMg alloy was investigated. The smaller size of Si particles of rheocast sample obtained by higher cooling rate and higher stirring ...
Leakage of an austenitic steel CO2 storage tank / Curenje posude za skladištenje CO2 od austenitnog čelika
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
After the occurrence of water droplets on the manhole outer wall of a storage tank for carbon dioxide, by detailed inspection, a net of cracks is detected in the manhole flange, close to the welded joint between the flange ...
Significance and applicability of structural integrity assessment / Značaj i primenljivost ocene integriteta konstrukcija
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
To avoid unexpected and frequent serious failures of objects and equipment in service, and save their structural integrity, proper experimental and theoretical analyses are required, that are supported by modeling and ...
Solvatochromism of 5-(4-substituted arylazo)-4-phenyl-6-methyl-3-cyano-2-pyridones / Solvatohromizam 5-(4-supstituisanih arilazo)-4-fenil-6-metil-3-cijano-2-piridona
(Engineering Society for Corrosion, Belgrade, Serbia, 2018)
Eight 5-(4-substituted arylazo)-4-phenyl-6-methyl-3-cyano-2-pyridones were synthesized by reaction of benzoylacetone and arendiazonium salt, followed by condensation with cyanoacetamide. Absorption spectra of all azo ...
Integrated procedure for recycling and valorization of useful components from secondary raw materials based on hard metals
(Savez inženjera metalurgije Srbije, Beograd, 2017)
Wide application of hard metals requires increased consumption of their constituents. Their high cost and scarcity impose the need for finding new, both ecologically and economically justified ways for their production. ...
Impedance characteristics of aluminum with sol-gel ceria protective coating during the exposure to chloride corrosion agent / Impedansni odgovor aluminijuma sa zaštitnom prevlakom oksida cerijuma tokom izlaganja hloridnoj korozionoj sredini
(Engineering Society for Corrosion, Belgrade, Serbia, 2016)
Electrochemical impedance characteristics of bare Al and Al with CeO2 coating prepared sol-gel procedure from the ceria sol are investigated. The corrosion behavior is monitored during the exposure to 3 wt. % NaCl aqueous ...
Integrity assessment of reverse engineered ti-6al-4v eli total hip replacement implant
(Society for Structural Integrity and Life, Institute for Material Testing, 2019)
Total hip replacement implants are used as an artificial replacement for disfunctional hips in order to sustain joint movement. Chosen material and design of total hip replacement are the most influential factors for ...
Assessment of the behaviour of fatigue loaded HSLA steel welded joint by applying fracture mechanics parameters / Procena ponašanja zavarenog spoja HSLA čelika opterećenog na zamor primenom parametara mehanike loma
(Society for Structural Integrity and Life, Institute for Material Testing, 2012)
From a fracture mechanics point of view on welded joints, it is assumed that the welded joint is pre-cracked such as that the fatigue life of the pre-cracked structure is then determined by the period of crack growth under ...