Претраживање
Приказ резултата 1-10 од 38
Some aspects of physical metallurgy of microalloyed steels
(Savez inženjera metalurgije Srbije, Beograd, 2019)
Some aspects of deformation, precipitation, and recrystallization behavior in medium carbon V-microalloyed and low carbon Nb/Ti-microalloyed steels are presented in the paper. Changes in microstructure are explained together ...
Numerical simulation of temperature field in the vertical bridgman method crystal growth
(Savez inženjera metalurgije Srbije, Beograd, 2015)
The mathematical model for heat transfer during the Bridgeman crystal growth, using the finite element method and the obtained result are presented. Some modifications to the method were introduced in order to incorporate ...
Kinetics of barite reduction from refractory barite-sulphide ore
(Savez inženjera metalurgije Srbije, Beograd, 2016)
Refractory sulphide-barite ore was reduced with carbon in order to release lead, zinc, and copper sulphide from barite-pyrite base. Mineralogical investigations showed that due to the complex structural-textural relationships ...
Investigation of copper(i) sulphide leaching in oxidative hydrochloric acid solution
(Savez inženjera metalurgije Srbije, Beograd, 2015)
Present work is focused on the copper (I) sulphide leaching with sodium chloride in hydrochloric acid solution and with introduction of gaseous oxygen. Chemical reactions of leaching and their thermodynamic probabilities ...
Application of raw volcanic rock found in etna valley as an adsorbent of chromates, arsenates and selenates
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This paper aims to determine the potential of volcanic rock found in Etna valley as an adsorbent of heavy metals in anionic form (chromates, arsenates, and selenates). Characterization of the volcanic rock was done with ...
The effect of calcinated hydroxyapatite and magnesium doped hydroxyapatite as fillers on the mechanical properties of a model bisgma/tegdma dental composite initially and after aging
(Savez inženjera metalurgije Srbije, Beograd, 2018)
This study aimed to investigate the possibility of modifying model BisGMA/TEGDMA dental composite by substituting 10 wt. % of conventional glass fillers with bioactive fillers based on calcinated nanosized hydroxyapatite ...
Bisphenol a removal from aqueous solution using fine alpha-fe2o3 particles
(Savez inženjera metalurgije Srbije, Beograd, 2018)
Iron(III) oxide particles (alpha-Fe2O3) were obtained from ferrous chloride (FeCl3 center dot 6H(2)O) precursor using ammonium hydroxide as a precipitating agent and particles were calcined at 700 degrees C for 4 h. ...
The influence of Mg and Mn content on abnormal grain growth in AA5182 type alloys
(Savez inženjera metalurgije Srbije, Beograd, 2019)
The occurrence of abnormal grain growth (AGG) in AA5182 alloy during annealing imposes severe restrictions on processing parameters and deteriorates mechanical properties. In this work, we investigated the effect of chemical ...
Ni-pd/al(2)o(3) catalyst supported on reticulated ceramic foam for dry methane reforming
(Savez inženjera metalurgije Srbije, Beograd, 2015)
In the present study, Ni-Pd/Al2O3 catalyst supported on alpha-Al2O3 based foam was prepared and evaluated in the dry methane reforming process. Corresponding metal chlorides were deposited to the foam surface by impregnation ...
Treatment of dispersed iron-bearing raw materials and modeling of the protection systems against air-pollution
(Association of Metallurgical Engineers of Serbia, 2016)
Based on the analysis of the non-standard iron-bearing raw materials treatment process and the results of real composition measurements of the flue gas, the study of hazards by identification of harmful substances that ...